---------------------------------------------------------------------------------------------------------------------------------------------------------
https://www.waveshare.net
深圳市微雪电子有限公司
LCD1602 RGB Module
深圳市微雪电子有限公司
---------------------------------------------------------------------------------------------------------------------------------------------------------
1. FUNCTIONS & FEATURES
https://www.waveshare.net
Features
一 Characters: 16×2 Lines
一 LCD Mode: STN, Yellow –Green/Blue/Grayish;
一 LCD Controller IC: AiP31068L or Equivalent
一 RGB Controller IC: PCA9633DP2 or Equivalent
一 Driving Method: 1/16 Duty; 1/5Bias
一 Viewing Angie: 6 O’clock direction
一 I2C MPU Interface
一 Backlight: RGB LED
一 Operating Temperature Range: -20 to +70℃;
一 Storage Temperature Range : -30 to +80℃;
2. MECHANICAL SPECIFICATIONS
SPECIFICATIONS
ITEM
Module Size
View Area
Number of Character
Character Size
Character Pitch
3. EXTERNAL DIMENSIONS
87.0L×32.0W×13.0(max)H
64.5×16.0
16×2 Lines
2.96×5.56
3.55×5.96
UNIT
mm
mm
—
mm
mm
2
深圳市微雪电子有限公司
---------------------------------------------------------------------------------------------------------------------------------------------------------
4. BLOCK DIAGRAM
https://www.waveshare.net
5. POWER SUPPLY
6. PIN DESCRIPTION
ITEM SYMBOL
LEVEL
1
2
3
4
SDA
SCL
GND
VCC
H/L
H/L
0V
+3.3~5.0V
FUNCTION
I2C-Bus Serial Data
I2C-Bus Serial Clock
Power Ground
Power Supply For Logic
3
深圳市微雪电子有限公司
---------------------------------------------------------------------------------------------------------------------------------------------------------
7. MAXIMUM ABSOLUTE LIMIT (Ta=25°C)
https://www.waveshare.net
Items
Supply Voltage
Input Voltage
Operating Temperature
Storage Temperature
Symbol
Vdd
Vin
Top
Tst
Min Max
0
0
-20
-30
5.2
Vdd
+70
+80
Unit
V
V
℃
℃
Condition
Vss=0V
Vss=0V
No Condensation
No Condensation
Note: Voltage greater than above may damage the module
All voltages are specified relative to VSS=0V
8. ELECTRICAL CHARACTERISTICS
8.1 DC Characteristics (VDD=+5.0V, VSS=0V, Ta=-0~+50°C)
TYP
—
Items
Operating Voltage
Test Condition
Symbol
VDD
Min
3.0V
Max
5.2
Unit
V
Supply Current
Input High Voltage 1
(Except OSC1)
Input High Voltage 2
(Except OSC1)
Output High Voltage 1
(DB0~DB7)
Output High Voltage 2
(Except DB0~DB7)
Input Leakage Current
Input Low Current
Internal clock(external Rf)
External clock
LCD Driving Voltage
IDD
VIH1
VIL1
VIH2
VIL2
VOH1
VOL1
VOH2
VOL2
IIKG
IIL
fOSC1
fOSC
duty
tR, tF
VLCD
Use internal
Oscillator/external
clock(VDD=5V,
fosc=250KHz)
—
—
—
—
IOH=-0.205mA
IOL=1.2mA
IO= -40uA
IO=40uA
VIN=0V~VDD
VIN=0V VDD=5V(pull
up)
Rf=91KΩ±2%,
VDD=5V
—
VDD-V5(1/5,1/4bias)
—
0.55
0.8
mA
2.5
-0.3
Vdd-1.0
-0.2
2.4
—
0.9Vdd
—
-1
-50
190
125
45
—
3.0
—
—
—
—
—
Vdd
0.6
Vdd
1
Vdd
0.4
—
— 0.1Vdd
—
1
-125
-250
270
270
50
—
350
410
55
0.2
11.0
V
V
V
V
V
V
V
uA
uA
KHz
KHz
%
uS
V
8.2 AC Characteristics (VDD=+5.0V, VSS=0V, Ta=-20~70°)
Characteristic
Symbol
SCL Cycle Time
SCL Pulse Width
SCL Rise/Fail Time
fSCLK
tLOW
tHIGH
Test
Condition
I2C
Min
TYP
—
1.3
0.6
—
—
—
Max
400
—
—
Unit
KHz
uS
uS
4
---------------------------------------------------------------------------------------------------------------------------------------------------------
https://www.waveshare.net
深圳市微雪电子有限公司
100
0
20
0.6
0.6
0.6
1.3
—
—
—
—
—
—
—
—
0.9
300
—
—
—
—
nS
uS
nS
uS
uS
uS
uS
tSU:DAT
tHD:DAT
tr,tf
tSU:STA
tHD:STA
tSU:STO
tBUF
Address Setup Time
Address Hold Time
SCL/SDA Rise/Pulse Time
START Steup Time
START Hold Time
STOP Steup Time
STOP、START Spacing
Interval
MPU write timing
START STOP:
ASK :
5
---------------------------------------------------------------------------------------------------------------------------------------------------------
https://www.waveshare.net
深圳市微雪电子有限公司
AiP31068L (LCD ) Slave Address : 0X7C.
PCA9633DP2 (RGB) Slave Address: 0XC0.
9. FUNCTION SPECIFICATIONS
9.1. Basic Setting
To drive the LCD module corretly and provide normally display, please use the following
setting:
一 N=1, 2-line display
一 F=0, 5×8 dots font
一 D=1, display on
Note:
一 These setting/commands should issue to the LCD module while start up.
一 See the Display Commands section for details.
9.2. Resetting The LCD Module
When turning on the VDD and VSS power supply, LCD module will execute the reset routine
automatically. It takes about 50ms. After the reset routine, the LCD module status will be as
follow:
一 N=1, 2-line display
一 Display clear
一 DL=1, 8-bit interface
6
---------------------------------------------------------------------------------------------------------------------------------------------------------
深圳市微雪电子有限公司
https://www.waveshare.net
一 F=0, 5×8 dot character font
一 D=0, Display off
一 C=0, Cursor off
一 B=0, Blinking off
一 I/D=1, Increment by 1
一 S=0, No shift
NOTE:
一 Reset routine could not generate the Basic Setting
9.3. Display Memory Map
There are two main memory-areas in the LCD module for display.
一 Character Generator RAM(CGRAM)
一 Display Data RAM(DDRAM)
9.3.1. Character Generator RAM(CGRAM)
Character Generator RAM is for storing the User-defined Characters(5×8 dots font). Totally 8
User-defined Characters(character code = 00h-07h) could be created.
The User-defined Character Codes are 00h and 07h. They could be called into DDRAM as
normal character.
7
---------------------------------------------------------------------------------------------------------------------------------------------------------
https://www.waveshare.net
深圳市微雪电子有限公司
9.3.2. Character code ROM
Please refer to AiP31068L datasheet.
8