Arcus␣II
Owner’s Guide
Trademarks
Arcus is a trademark of Agfa-Gevaert, NV.
Apple and Macintosh are registered trademarks of Apple Computer,
Incorporated.
IBM PC, AT, XT and PS/2 are trademarks of International Business
Machines Corporation.
Other product or company names are trademarks or registered
trademarks of their respective holders.
Copyright © 1994 Agfa-Gevaert N.V.
All rights reserved
ii
Contents
Arcus␣II scanner and Transparency Module
regulation compliance v
Safety regulations v
Electromagnetic Interference vi
Introduction xi
Conventions xi
Important safety instructions xi
1 Preparing the scanner 3
Unpacking the scanner 3
Unlocking the scanner and the transparency module 4
Locking the scanner and the transparency module 5
Taking a closer look 7
Testing the scanner 8
2 Installation 11
About SCSI devices 11
Changing the SCSI ID number 12
Installation for the Macintosh 13
Choosing a SCSI ID number 13
Connecting the scanner 14
Testing the connection 16
Installation for the PC 17
Which SCSI adapter card 17
Choosing a SCSI ID number 17
Connecting the scanner 18
Testing the connection 20
Installation for the IBM PS/2 21
Which SCSI adapter card 21
Connecting the scanner 22
Testing the connection 22
Contents iii
3 Using the scanner 25
Placing a reflective original 25
Placing a transparent original 25
4 Caring for your scanner 29
Cleaning the scanner and the transparency module 29
Replacing the fluorescent lamps 29
Troubleshooting 31
Technical Information 33
Arcus␣II scanner specifications 33
Memory Configuration 35
iv Contents
Arcus␣II scanner and Transparency Module
regulation compliance
Safety regulations
The Arcus␣II scanner and Transparency Module are designed to
comply with:
VDE 0805, IEC 950
GS approved
UL 1950-D3
CSA c22.2 No. 950 - M89 D3
UL Safety Statement
Instructions for power supply cord selection:
For modules set at 115V:
Use a UL listed, Type SVT or SJT cord, three conductor, rated 10 A
125 V, not to exceed 15ft in length.
❖ Warning: For the reason of safety, besides the personal maintenance
mentioned in this operation manual, don’t try to remove any mechanical
parts or any electronic devices. If you need service, our dealer and service
offices are available to help you.
FTZ: Bescheinigung des Herstellers/Importeurs
Hiermit wird bescheinigt dass der Image Scanner in Übereinstimmung
mit den Bestimmungen der vgf 1046/1984 funk-entstört ist.
Der Deutschen Bundespost wurde das inverkehrbringen dieses Gerätes
angezeigt und Berechtigung zur Überprüfung der Serie auf Einhaltung
der Bestimmungen eingeraumt.
TÜV: Wichtige Sicherheitshinweise
1. Bitte Lesen Sie sich diese Hinweise sorgfältig durch.
2. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur
Zuberhörteile verwenden, die vom Hersteller zugelassen sind.
3. Das Gerät ist vor Feuchtigkeit zu schützen.
4. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.
Ein Kippen oder Fallen könnte Verletzungen hervorrufen.
Verwenden Sie nur sichere Standorte und beachten Sie die
Aufstellhinweise des Herstellers.
v
5. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät
vor Überhitzung schütz. Sorgen Sie dafür, daß diese Öffnungen
nicht abgedeckt werden.
6. Die Netzanschulßsteckdose muß aus Gründen der elektrischen
Sicherheit einen Schutzleiterkontakt haben.
7. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder
Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw.
elektrischen Schlag auslösen.
8. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der
elektrischen Sicherheit nur von authorisiertem Servicepersonal
geöffnet werden.
9. Die Steck dose sollte nahe dem Gerät und leicht zugänglich sein.
Electromagnetic Interference
The Arcus␣II scanner is designed to comply with:
VDE 0871, class B
VDE 0875, level N
FCC 20718, part 15, subpart B, class B
Federal Communications Commission Radio Frequency Interference
Statement.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
residential installation. This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used in
accordance with the instruction manual may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
vi
■ Consult the dealer or an experienced radio TV technician for help.
Notice:
(1) The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
(2) Shielded interface cables with ferrite core installed on scanner
connector end must be used with this equipment.
Canadian department of Communications
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques (de la class
B) prescrites dans le Règlement sur le brouillage radioélectriques
édicté par le ministère des Communications du Canada.
vii
viii