第1页 / 共9页
第2页 / 共9页
第3页 / 共9页
第4页 / 共9页
第5页 / 共9页
第6页 / 共9页
第7页 / 共9页
第8页 / 共9页
brinno数码摄像机-GardenWatchCam说明书.pdf
Watch Your Garden Grow
The Brinno GardenWatchCam is a low cost, light weight,
weather resistant, battery operated time-lapse camera
that captures the entire lifecycle of any garden season
by taking photos at predetermined time settings.
7F, No.75, Zhou Zi St., Taipei City 11493, Taiwan
-0306 F +886-2-8751-0549
www.brinno.com
301-0002-10 EN-A2
Package Contents
GardenWatchCam unit
Mounting Stake
2GB USB Flash Drive
4 AA Batteries
CD with software
User Manual
Brinno Incorporated’s GardenWatchCam Users Manual
Thank you for purchasing the Brinno GardenWatchCam. The Brinno
GardenWatchCam is designed to allow you to capture the entire life cycle
of a growing garden from the first bud to the last leaf falling,
or capture anything else that happens depending on where you set your
camera up. It comes complete with everything you need to begin capturing
all the growthand life in your garden and is easy to set up and use.
Let’s get started.
Minimum Requirements to install and run the software
Windows 98 and above.
‧02
03‧
How to set up your Brinno GardenWatchCam
1. Remove the GardenWatchCam from the
package.
2. Check to make sure that all the contents are
included.
3. Open up the GardenWatchCam by placing it
Lens side down on a flat surface, or Lens side
down in the palm of your hand, and remove
the battery door by pulling open the latch.
4. With the wheel in the middle of the camera
you can choose between one of seven time
interval settings. Simply rotate the wheel with
your finger left or right to choose the desired
setting.
Macro Image
Standard Image
Lens
Power Button
The Custom Time Interval setting options are as follows:
Wheel position
Time interval between pictures
1
2
3
4
5
6
7
1 minute
5 minutes
30 minutes
1 hour
4 hours
24 hours
Custom ( Factory setting = 5 seconds )
** To modify the 7th custom setting, insert the CD included with your GardenWatchCam
into your computer, and follow the instructions.
The custom setting can range anywhere from 5 seconds to 11 hours and 59 minutes and 59 seconds.
The factory default custom setting is set to 5 seconds.
(The specific steps to install the software onto your computer as well as your USB
Flash Drive are listed below on page 8-11).
Battery Cover
Mounting
Hole
AA Battery
AA Battery
USB
Flash Drive
AA Battery
Wheel
AA Battery
‧04
05‧
5. Insert 4 AA batteries following the polarity
you hear it “click” to ensure the door is closed
Choosing your Lens setting
b- Macro Setting :This option is obtained
markings (+ -) inside the camera.
properly.)
6. Insert any standard USB Flash Drive into the
GardenWatchCam in the open slot between
the batteries.
***(Please note that the maximum size
USB Flash Drive that the GardenWatchCam
supports is a 8GB USB Flash Drive. If you
use a USB Flash Drive with a larger
memory density the camera will not
function properly.)
7. Replace the battery door on the GardenWatch-
Cam. (Make sure to push down the latch until
Mounting your GardenWatchCam
(2 options)
8. a- To set your GardenWatchCam on the
mounting stake, screw the mounting
stake clockwise into the hole on the
bottom of the camera. (See Images above)
OR
b- To set your GardenWatchCam on any
standard tripod, screw the tripod clockwise
into the hole on the bottom of the camera.
9. The GardenWatchCam has two lens positions
that determine the focal distance and the
depth of field of the camera :
a- Standard Setting :This option is
obtained by turning the lens bezel to the
“mountain” icon position. This will give a
depth of field that extends from approximately
1 meter (2.6 feet) and beyond, and is best for
getting shots of an entire garden or large area.
OR
by turning the lens bezel to the “flower” icon
position. This setting allows the camera to
focus on an object that is approximately 0.5
Meters (19 inches) away from the camera.
Because the depth of field is significantly
reduced when using Macro setting, subjects
in the background will be out of focus.
This setting is best for following the growth
of a single bloom, or any other subject that
requires close-up observation.
‧06
07‧
10.After choosing the lens setting appropriate to
the subject to be photographed, the camera
should be aimed so that the lens is pointing at
the center of the subject. Because the field of
view of the lens is quite wide, the positioning
of the GardenWatchCam does not have to be
extremely precise. But because a typical time
lapse sequence takes place over a long period
of time, it is suggested that a short test
session (with a short time interval) be used to
ensure correct positioning of the Garden-
WatchCam. Once the positioning has been
verified, then the desired time interval for the
full time lapse sequence can be set, and its
time to take pictures.
The table below shows the approximate image size (width x height) based
on the distance between the camera and the subject(s) to be captured.
Mode
Distance from Target
Target Area captured
Target Area captured
Area (Meter / Inch)
Width (cm / inch)
Height (cm / inch)
Macro view
0.5m / 19inch
36cm / 14inch
30cm / 12inch
Standard view
1m / 39inch
2m / 78inch
75cm / 29inch
56cm / 22inch
146cm / 57inch
110cm / 43inch
3m / 118inch
219cm / 86inch
168cm / 66inch
The table above shows some typical distances, but since the GardenWatchCam is capable of focusing on
objects that are far away (in standard mode), the GardenWatchCam can also be used to photograph many
other subjects.
For example, you could set up the GardenWatchCam to take a photo once every 24 hours to capture the
process of a house being built over several months. Or get a picture of the sunset every day for a year.
The possibilities are only limited by your imagination and creativeness!
** Please note that the AVI files created by the GardenWatchCam can be viewed on the program
“GardenWatchCam Player” in the CD supplied with GardenWatchCam or using Windows media player, or
most other AVI players.
GardenWatchCam Operation
On the front of the GardenWatchCam, above the lens, there are three LED lights. These LEDs allow you
to monitor the status of the camera without having to move the camera from its mounted position.
Each LED supports a different function :
Green LED light：Power ON/OFF and Status
Red LED light：Low Battery Level
Blue LED light：Low USB flash drive Level
Beep voice:
Power On: 2 times beep
Power Off: 3 times beep
Register setting change: 3 times beep
Error status: 6 times beep
( Error= No USB insert, USB memory short, Low battery)
To turn on the GardenWatchCam
Press and hold the orange power button on the
front of the camera until the green LED lights up.
After a few seconds the GardenWatchCam will
beep twice to indicate it has properly initialized
and is waiting to start a time-lapse sequence.
After a delay of approximately 5 seconds the
GardenWatchCam will take the first picture of
the time-lapse sequence.
NOTE : If the USB flash drive is full, or the
batteries are completely empty, the Garden-
WatchCam camera will not turn on.
If the batteries are too low for normal operation,
the GardenWatchCam will turn on beep twice,
the red LED will turn on, and then the Garden-
WatchCam will beep six times and then turn off.
If the USB flash drive is full, or not installed, the
GardenWatchCam will turn on beep twice, then
after a few seconds the blue LED will turn on,
then the GardenWatchCam will beep six times
and then turn off.
During GardenWatchCam operation the Green
LED will turn on for about one second every
15 seconds to indicate that the camera is
running properly and is ready to take
photos. If there is any other status to
report, the camera will do so at the same
time as the green LED flashes. If the batteries
are getting low the red LED will turn
on in unison with the green LED. If the USB flash
drive is getting close to being full, then the blue
LED will turn on in unison with the green LED.
If the camera has previously automatically shut
down due to low batteries or a full USB flash
drive, the next time the power button is pressed
the red or blue LED will turn on and will stay on
until the green LED turns on. This allows you to
determine the cause of the automatic shutdown
so that the appropriate corrective action can be
taken.
The Green LED will also turn on and flicker for a
few seconds while a picture is captured at the
chosen time setting, and then is stored on the
USB flash drive. This indication of GardenWatch-
Cam activity is independent of the status
indication that occurs every 15 seconds.
To turn off the GardenWatchCam
Press and hold the orange power button until
the GardenWatchCam beeps three times and the
green LED turns off. This may take several
seconds because the GardenWatchCam must
first power itself on and initialize before it
recognizes the turn off request. Please be
patient and wait for the beeps and LED
indication.
‧08
09‧
Installing the software for your GardenWatchCam
If you choose this option, the next step is to
read the user agreement. If you agree, then
click “Yes, I do” to continue.
There are 2 programs on the CD supplied with the GardenWatchCam. The first program, “Garden-
WatchCam Setup” allows you to set the time and date of the GardenWatchCam to your local time.
This program also allows you to set the time interval for the Custom setting on the GardenWatchCam.
The second program called “GardenWatchCam Player” allows you to play the videos taken by the
GardenWatchCam. (If you have misplaced your CD you can download the program from
www.brinno.com).
Before running the GardenWatchCam programs, they must first be installed on your computer using
one of the methods described below.
Standard Installation
Manual Installation
1. Insert the GardenWatchCam CD into your
computer.
2. The CD will automatically open to the folder
named “Brinno GardenWatchCam”, where
you will see an icon named “Setup GWC”.
3. Double click on this icon to start the setup
program.
If you insert your CD into your computer and
it doesn’t automatically open up to show the
“Setup GWC” icon, use the following
procedure to install the program manually.
1. Browse to the CD and find the
“Setup GWC” icon.
2. Double click on this icon to start
the setup program.
Two installation options are provided.
The No Questions Asked Installation option
is the standard installation and asks no technical
questions. This is the recommended method of
installing the time, date and custom time
interval setting program.
The Do Not Install option allows you to exit
the setup program without installing “Brinno
GardenWatchCam”.
The software will then be loaded onto your
computer and you can click the “Thanks”
button to complete the installation.
The setup program will then create and open
a program group called “GardenWatchCam”
containing three icons.
The “GardenWatchCam Setup” icon is used
to start the time, date and custom time
interval setting program.
The “GardenWatchCam Player” is used to
play the videos taken by GardenWatchCam.
The “Remove GardenWatchCam”icon can be
used to uninstall the program
‧10
11‧
How to use “GardenWatchCam Setup”
“GardenWatchCam Setup” allows you to set the time and date of the GardenWatchCam to your local
time. This program also allows you to set the time interval for the Custom setting on the Garden-
WatchCam.
A
B
C
E
D
A
Fluorescent Lighting Frequency
Select the correct lighting frequency to
match your indoor lighting frequency.
eg. USA: 50Hz, Europe: 60Hz
None: Turns the flicker filter off. This is the
normal way to operate a camera in an
outdoor environment.
B
Local Time and Date
Set the time and date to your local time.
C
D
E
Custom Time
You can set the custom time from 5 seconds
to 11 hours 59 minutes 59 seconds.
Low Light Record
This option allows your GardenWatchCam
to work in low light environments.
USB Flash Drive
Select a drive letter assigned to your USB
flash drive.
5. Turn on the GardenWatchCam. When the
GardenWatchCam detects the time and date
file on the USB flash drive it will automatically
load the data from the file, beep three times,
then turn off. The next time you turn on the
GardenWatchCam it will be set to the time
and date that were in the file. The Garden-
WatchCam will also remember the Custom
interval setting that was in the file.
Once you have set up your GardenWatch-
Cam you are READY to begin capturing all
the garden action in your backyard!
Loading your Time and Date Stamp and
Custom Time Interval Setting onto your
USB Flash Drive :
1. Insert your USB Flash Drive into any available
USB port on your computer. Windows will
automatically assign a drive letter to the USB
flash drive. Make a note of the drive letter
assigned to the USB flash drive.
2. Start the “GardenWatchCam Setup” program
by double clicking the “GardenWatchCam
Setup” icon in the “GardenWatchCam”
program group. If the program group is not
open, you can open it by using the “Start..
Programs.. Brinno..” menus to find the
program group.
3. The “GardenWatchCam Setup” program has a
number of fields that can be modified. There
are two fields that allow the time and date to
be set, and there are three fields that allow the
Custom time interval to be set.
A sixth field is used to tell the program which
drive is to be used to store the file with the
time and date and custom time interval
data.Make sure the drive letter in this field
matches the drive letter in step 1. Once all the
fields have been set, hit the OK button to save
the file.
4. Remove the USB flash drive from your
computer’s USB port. Make sure your
GardenWatchCam is turned off, and then
insert the USB flash drive into your
GardenWatchCam in between the 4 AA
batteries on each side.
‧12
13‧
How to use “GardenWatchCam Player”
Start the “GardenWatchCam Player” program by double clicking the “GardenWatchCam Player” icon
in the “GardenWatchCam” program group. If the program group does not open, you can open it by
using the “Start.. Programs.. Brinno..” menus to find and open the program group.
GardenWatchCam Player
GardenWatchCam player is designed for
use with the Brinno’s GardenWatchCam.
The AVI file format produced by the
GardenWatchCam is a Motion
JPEG-encoded AVI in a standard format
recognized by Microsoft’s Windows
Media Player and most other Generic
Video Players.
NOTE The GardenWatchCam Player is NOT a general-purpose media player. It is a dedicated Player
designed specifically to play AVI’s produced by the GardenWatchCam. AVI’s NOT generated by
Brinno’s GardenWatchCam will not play properly with this player.
The following sections describe the controls used
to control the player.
1.1. Menu Functions
1.1.1. File – Open
“File Open” allows the user to select an AVI file
for loading and displaying. Multiple files can
be selected, and will be added to the playlist.
1.1.2. File – Save Current
“File Save” .The currently-displayed frame can
be saved as a JPEG file.
1.1.3. File – Exit
This exits the application. The standard
Windows close application commands will also
function as expected
1.2. Drag and Drop Interface
In addition to the standard menu commands,
GardenWatchCam Player supports a “drag-and-
drop” interface. If the application is open,
dragging and dropping a file or group of files
causes it to add the selected files to the playlist.
Statistics display
Key statistics for the video
sequence are shown in a
statistics box, displayed in
the upper-right corner of
the application window.
Capture Interval: The
number of elapsed seconds
between frames. This is
determined by switch
settings on the camera, and
the information is embedded in the video
sequence.
Elapsed Time: This is the amount of time elapsed
since the beginning of the sequence.
Date/Time: Assuming that the correct date and
time have been set in the camera’s real time
clock, this is the time and date at which the
currently-displayed frame were captured.
1.3. Speed Control
1.4.3. Single Step Forward Control
Pressing this control causes the player to
display the next frame in the sequence.
1.4.4. Single Step Backward Control
Pressing this control causes the player to
display the previous frame in the
sequence.
1.4.5. Pause Control
Pressing this control during play stops
the player at the current frame. In Pause
mode, single step forward and backward
are enabled.
1.4.6. Stop Control
Pressing this control during play stops
the player, and returns it to the first
frame of the sequence. Single-step
forward function is enabled.
1.5. Seek Control
When the player is in Pause or Stop mode, the
seek control is displayed. This can be used to
seek any point in the sequence, either by
watching the images in the display window, or
by monitoring the elapsed time or real-time
indicators.
NOTE - During play mode, the seek control is
concealed.
The Speed Control is a vertical tracking
control on the right side of the display
window. This is used to set the
playback rate. Because this is a
time-lapse camera, the playback rate
has to be different from the recording
rate.
Note that in some installations, if the
requested playback rate exceeds the
host PC’s ability to decompress and
display frames, some frames may be
skipped in order to keep up with the
requested GardenWatchCam rate.
For a mode in which frames will never
be skipped, read about the Motion
Search feature, described below.
1.4. Play Controls
Controls are enabled or grayed-out, depending
on their functionality. For example, while playing
the video forward or backward the single-step
buttons are grayed out.
1.4.1. Forward Play Control
Controls are enabled or grayed-out,
depending on their functionality.
For example, while playing the video
forward or backward the single-step
buttons are grayed out.
1.4.2. Reverse Play Control
The reverse play control causes the
player to play in reverse until either the
beginning of the sequence is reached, or
the stop or pause control is pressed.
相关推荐
2023年江西萍乡中考道德与法治真题及答案.doc
2012年重庆南川中考生物真题及答案.doc
2013年江西师范大学地理学综合及文艺理论基础考研真题.doc
2020年四川甘孜小升初语文真题及答案I卷.doc
2020年注册岩土工程师专业基础考试真题及答案.doc
2023-2024学年福建省厦门市九年级上学期数学月考试题及答案.doc
2021-2022学年辽宁省沈阳市大东区九年级上学期语文期末试题及答案.doc
2022-2023学年北京东城区初三第一学期物理期末试卷及答案.doc
2018上半年江西教师资格初中地理学科知识与教学能力真题及答案.doc
2012年河北国家公务员申论考试真题及答案-省级.doc
2020-2021学年江苏省扬州市江都区邵樊片九年级上学期数学第一次质量检测试题及答案.doc
2022下半年黑龙江教师资格证中学综合素质真题及答案.doc
