富士通扫描仪-M3091DC说明书.pdf-资料库

第1页 / 共63页

第2页 / 共63页

第3页 / 共63页

第4页 / 共63页

第5页 / 共63页

第6页 / 共63页

第7页 / 共63页

第8页 / 共63页

C150-E140-03EN M3091DC Image Scanner OPERATION GUIDE 2-

FOR SAFE OPERATION Treatment of This Manual Since this manual contains important information for using the M3091DC, read it thoroughly before using the product. Use the M3091DC only after thoroughly reading and understanding especially the section "Important Alert Messages" in this manual. Keep this manual handy, and store it carefully. Notice to Federal Communications Commission American Users Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Adjust or relocate the receiving antenna. • Increase the distance between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from the circuit the receiver is connected to. • Consult your dealer or an experienced radio/TV technician for help. FCC warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. M3091DC Image Scanner Operation Guide

Notice to Notes American Users • The use of a non-shielded interface cable with the referenced device is prohibited. The length of the parallel interface cable must be 3 meters (10 feet) or less. The length of the serial interface cable must be 15 meters (50 feet) or less. • The length of the power cord must be 3 meters (10 feet) or less. Notice to This digital apparatus does not exceed the class B limits for radio noise Canadian Users emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numériqué n'émet pas de bruits radioélectnques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édic té par le ministère des Comunications du Canada. Notice to Bescheinigung des Herstellers/Importeurs German Users Hiermit wird bescheinigt, daß der/dieldas • M3091DC in Übereinsstimmung mit den Bestimmungen der • AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie auf Einhaltung der Bestimmungen eingeräumt. • Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991: Der höchste Schalldruckpegel beträgt 70 dB (A) order weniger gemäß ISO/7779. M3091DC Image Scanner Operation Guide

Warning: This equipment may cause electromagnetic interference. It has not been tested to show compliance with AS3548 Class A equipment, which is designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference. As an E ® NERGYSTAR Partner, Fujitsu Limited has determined that this scanner meets E ® NERGYSTAR guidelines for energy efficiency. E S ® NERGY TAR is a U. S. registered mark. Trademark Acknowledgment Fujitsu is a registered trademark of Fujitsu Limited. Third Edition April 2000 The contents of this manual may be revised without prior notice. The contents of this manual shall not be disclosed in any way or reproduced in any media without the express written permission of Fujitsu Limited. All Rights Reserved, Copyright  FUJITSU LIMITED 1999 M3091DC Image Scanner Operation Guide

Preface Thank you very much for your purchase of the M3091DC Image Scanner. The M3091DC Image Scanner can read very fine color images. As this manual explains the basic handling of the scanner, read it carefully to use the scanner properly. In this manual, the Microsoft Windows NT Operating System is referred to as Windows NT, the Microsoft Windows 95 Operating System is referred to as Windows 95, and the Microsoft Windows 98 Operating System is referred to as Windows 98. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation of the U.S. in the United States and other countries. Other company names or product names appearing in this manual are trademarks or registered trademarks of individual companies. M3091DC Image Scanner Operation Guide i

Important Notes to Users Every user is requested to use this product including the manuals and software supplied with the product at the user's own responsibility. Fujitsu assumes no liability with respect to any damage or loss caused to data as the result of using this product. Please understand that the warranty range for failure of this product will never exceed the amount of money paid by the user for the product. Fujitsu prohibits any user from using software supplied with this product or any other update software for this product for any purpose other than incorporation into this product. Fujitsu also prohibits any user from reworking or disassembling such software. ii M3091DC Image Scanner Operation Guide

Conventions for Alert Messages This manual uses alert messages to prevent users and bystanders from being injured or from suffering damage to their property. An alert message consists of an alert signal and alert statements. The alert signals and their meanings are as follows. This indicates a hazardous situation that could result in serious personal injury if the user does not perform the procedure correctly. This indicates a hazardous situation that could result in minor or moderate personal injury if the user does not perform the procedure correctly. This alert signal also indicates that damage to the products or other property may occur if the user does not perform the procedure correctly. In addition to the above-cited signals, the following symbols are also used to provide detailed information concerning injury or damage: Electric shock The symbol marked with indicates a warning or caution. The concrete meaning of an alert is illustrated in the symbol. (The example at left indicates caution High temperature against an electric shock and caution against an high temperature.) M3091DC Image Scanner Operation Guide iii

Disassembly The symbol marked with indicates what must not be done (prohibited action). The concrete meaning of the action is illustrated in the symbol. (The example at left indicates the prohibition of disassembly.) Plug The symbol marked with indicates what must be observed. The concrete meaning of the action is illustrated in the symbol. (The example at left directs the operator to disconnect the power plug from the outlet.) iv M3091DC Image Scanner Operation Guide

资料库

富士通扫描仪-M3091DC说明书.pdf

相关推荐

扫描仪

热门标签

最新资料