三洋投影机-LNS-W32说明书.pdf-资料库

第1页 / 共20页

第2页 / 共20页

第3页 / 共20页

第4页 / 共20页

第5页 / 共20页

第6页 / 共20页

第7页 / 共20页

第8页 / 共20页

LCD PROJECTOR LENS MODEL LNS-W32 LENS REPLACEMENT PROCEDURE NOTE; Lens installation is different in cabinet design and lens attachment method (Type A, B and C). Before installation the lens, check cabinet design and proper installation should be made. NOTES ON LENS REPLACEMENT The ZOOM, FOCUS and LENS SHIFT adjustment on the Top Control or the Remote Control cannot be operated with this Lens. Lens replacement should be performed by the qualified service personnel. It should be followed by this procedure precisely. Before attempt to replace the lens, confirm the model number (both the LCD projector and the lens) and use the proper lens. The lens cover is on the lens for protection. Be sure to remove the lens cover before installation. When installing or removing the lens, be careful not to stain, scratch or damage the lens. PARTS LIST Following parts are contained in the packing. G LENS G LIGHT-BLOCK SHEET BASE G DRIVER (3 mm, Green) G DRIVER (4 mm, Yellow) G LIGHT-BLOCK SHEET G SCREW 1 piece 1 piece (Part No. 610 310 8001) 1 piece (Part No. 610 287 7328) 1 piece (Part No. 610 275 6029) 1 piece Type PC1 (Part No. 610 310 7967) 1 piece Type PD1 (Part No. 610 294 3047) 2 pieces (Spare parts) Following checks and confirmations should be taken for safety. Check the following things by the time of the cabinet assembly after the lens replacement. 1. Check the lens is securely fixed. 2. Check no parts is missing, or no mounting part is loose. Some parts are not used for installation or replacement. Keep these parts and drivers included in the lens for later use. 1AA6P1P3217A- (ICZAA-A)

LENS REPLACEMENT PROCEDURE (FOR "A" TYPE) NOTE; When installation of this lens to the "A" type, needs an additional Front Panel. Contact to our sales dealer for ordering. Perform the steps 1 to 5 for lens replacement. SCREW "A" First set the lens at the center position with lens shift adjustment. 1 REMOVE THE LENS COVER AND LIGHT- BLOCK SHEET (See Figure-1 and 2) 1. 2. 3. Remove 2 screws-A. Press the button (or remove 2 screws-B) on the lower of the front panel and remove the front panel. Remove the light-block sheet from the light- block sheet base. 2 REMOVE THE LIGHT-BLOCK SHEET BASE (See Figure-3 and 4) 1. 2. Slide the light-block sheet base upward. Remove the light-block sheet base. BUTTON Fig-1 LIGHT-BLOCK SHEET BASE FRONT PANEL LIGHT-BLOCK SHEET SCREW "B" (Some models) Fig-2 LIGHT-BLOCK SHEET BASE Fig-3 LIGHT-BLOCK SHEET BASE Fig-4 -2-

3 REMOVE THE LENS (See Figure-5 and 6) 1. 2. 3. Disconnect the Lens Shift connector "K16L" from the circuit board on cabinet left side. Disconnect the Zoom and Focus connector "K16J" from the circuit board. Remove the lens motor lead from lead holder. Remove screws-C (4 screws) which fastens the lens and remove the lens. Use the driver (3 mm, Green) included with the lens to remove the screws. Be careful not to drop the lens when removing the screws. LENS MOTOR LEAD HOLDER SCREW "C" CIRCUIT BOARD ON CABINET LEFT SIDE CONNECTOR "K16L" LENS MOTOR LEAD CONNECTOR "K16J" Fig-5 -3-

4 MOUNT THE LENS (See Figure-5 and 6) 1. 2. Remove protective caps (front and back) on the lens. Mount the lens on lens mounting bracket with 4 screws. Use the driver (4 mm, Yellow) included with the lens to fasten the screws. CONFIRM THE FOCUS Project picture on screen and confirm the focus. If proper focus is not observed at screen, adjust focus following Focus Adjustment on this page. 5 MOUNT THE LIGHT-BLOCK SHEET AND FRONT PANEL (See Figure-7) 1. 2. 3. Mount the light-block sheet to the lens as shown in the Figure-7. Use the sheet included with the lens. Make sure the part no. and mark (TOP and BACK) on Light-Block Sheet and set them properly. Mount the Front Panel (Separately ordered) with the screws. ※ Light block sheet base is not used. DRIVER IN THE LENS LENS MOUNTING BRACKET Fig-6 LIGHT-BLOCK SHEET Type PD1 (Part No. 610 294 3047) Fig-7 FRONT PANEL (OPTIONAL PART) FOCUS ADJUSTMENT Set up the projector and project image on the screen. 1. Loosen the Focus Lock Screw on the lens. 2. Rotate the lens to obtain proper focus on center area of the screen. 3. Tighten the Focus Lock Screw. When proper focus is not observed at outer area of the screen, proceed to following adjustments. 4. Loosen the Focus Lock Ring of the lens. (Turn the Lock Ring to counter-clockwise.) 5. Rotate the lens to obtain proper focus on outer 6. Lock the Focus Lock Ring securely. (Turn the Lock area of the screen. Ring to clockwise.) Focus Lock Ring If proper focus is not observed entire screen, repeat above adjustment 1~ 6. Focus Lock Screw -4-

LENS REPLACEMENT PROCEDURE (FOR "B" TYPE) Perform the steps 1 to 5 for lens replacement. First set the lens at the fully lower position with lens shift adjustment. 1 REMOVE THE LENS COVER AND FRONT CABINET 1. 2. 3. Turn the lens cover to counter-clockwise and pull it toward front and remove the Lens Cover. Remove 2 Screws-A. Remove the front cabinet See Figure-1-1 and 2. 1. 2. Remove 3 Screws-A. Remove the front cabinet See Figure-1-2 and 2. 1. 2. 3. Pull Lens Cover toward front and remove it. Remove 2 Screws-A. Remove the front cabinet See Figure-1-3 and 2. SCREW "A" FRONT CABINET LENS COVER Fig-1-1 SCREW "A" FRONT CABINET Fig-1-2 LENS COVER SCREW "A" 2 REMOVE THE LIGHT-BLOCK SHEET BASE AND LIGHT-BLOCK SHEET (See Figure-2) FRONT CABINET Fig-1-3 LIGHT-BLOCK SHEET BASE 1. 2. Slide the light-block sheet base upward and remove it. Remove the light-block sheet from lens. LIGHT-BLOCK SHEET LENS COVER FRONT CABINET Fig-2 -5-

3 REMOVE THE LENS (See Figure-3 and 4) 1. 2. Remove the lens motor connector from terminal. Loosen the screws-B (2 screws) which fastens the lens. {Use the driver (4 mm, Yellow) included with the lens to loosen the screws.} Slide the lens lock latches to "UNLOCK" position and remove the lens. 3. SCREW "B" LENS LOCK LATCHES Be careful not to drop the lens when removing the screws. After using, save the driver for latter use. CONNECTOR Fig-3 TERMINAL LENS LOCK LATCHES LOCK POSITION UNLOCK POSITION Fig-4 LENS MOUNTING BRACKET DRIVER IN THE LENS LOWER SCREWS Fig-5 4 MOUNT THE LENS (See Figure-5) 1. Remove protective caps (front and back) on the lens. Mount the lens on lens mounting bracket with Upper 2 screws. Use the driver (4 mm, Yellow) included with the lens to fasten the screws. Remove the lower 2 screws on the Lens. (Lower 2 screws are not used.) Slide the lens lock latches to "LOCK" position and lock the lens. (See Figure-4) 2. 3. CONFIRM THE FOCUS Project picture on screen and confirm the focus. If proper focus is not observed at screen, adjust focus following Focus Adjustment on next page. -6-

5 MOUNT THE LIGHT-BLOCK SHEET AND LIGHT-BLOCK SHEET BASE (See Figure-6) 1. 2. Mount the light-block sheet on the lens. (In the same position as the removed sheet has been placed). Use the sheet included with the lens. Make sure the mark (TOP and BACK) on Light-Block Sheet and set them properly. Mount the light-block sheet base included with the lens. LIGHT-BLOCK SHEET Type PC1 (Part No. 610 310 7967) LIGHT-BLOCK SHEET BASE 6 MOUNT THE FRONT CABINET AND LENS COVER (See Figure-7) Mount the front cabinet with 2 screws. 1. ※ Lens cover is not used. FOCUS ADJUSTMENT Set up the projector and project image on the screen. 1. Loosen the Focus Lock Screw on the lens. 2. Rotate the lens to obtain proper focus on center area of the screen. 3. Tighten the Focus Lock Screw. When proper focus is not observed at outer area of the screen, proceed to following adjustments. 4. Loosen the Focus Lock Ring of the lens. (Turn the Lock Ring to counter-clockwise.) 5. Rotate the lens to obtain proper focus on outer 6. Lock the Focus Lock Ring securely. (Turn the Lock area of the screen. Ring to clockwise.) FRONT CABINET Fig-6 Fig-7 Focus Lock Ring If proper focus is not observed entire screen, repeat above adjustment 1~ 6. Focus Lock Screw -7-

LENS REPLACEMENT PROCEDURE (FOR "C" TYPE) SCREW "A" FRONT CABINET Perform the steps 1 to 6 for lens replacement. First set the lens at the fully lower position with lens shift adjustment. 1 1. 2. 3. REMOVE THE LENS COVER AND FRONT CABINET Turn the lens cover to counter-clockwise and pull it toward front and remove the Lens Cover. Remove 2 Screws-A. Remove the front cabinet 2 REMOVE THE LIGHT-BLOCK SHEET BASE AND LIGHT-BLOCK SHEET 1. 2. Slide the light-block sheet base upward and remove it. Remove the light-block sheet from lens. LENS COVER LIGHT-BLOCK SHEET BASE LIGHT-BLOCK SHEET LENS COVER FRONT CABINET LENS LOCK LEVER Pull the Lens Lock Lever upward 3 REMOVE THE LENS 1. 2. 3. Grasp the Lens Lock Lever and turn it fully upward. Remove the Lens into the projector. Disconnect the lens motor lead connector to the socket on the lens attachment. Remove 4 Screws and remove lens attachment. SCREW LENS ATTACHMENT SOCKET CONNECTOR LENS MOTOR LEAD - 8 -

资料库

三洋投影机-LNS-W32说明书.pdf

相关推荐

投影机

热门标签

最新资料