User Guide for DC2200
0
User Guide for DC2200
CONTENTS
Introduction
Electromagnetic Compatibility Notice
Precautions
Battery Used for DC2200 Camera
Nomenclature
Connect the camera unit by USB cable
TV Mode
Review – Reviewing Pictures
Slide Show
Info
Lang
Status LCD display
Recording a movie
Host Software
Install the Arcsoft programs
Install the camera driver
Upload photos
Use of PhotoFantasy
Use of PhotoStudio and PhotoPrinter
Product Specifications
Software and System Requirement
2
3
4
5
6
7
8
9
10
11
12
13 - 18
19
20
21
22
23
24
25
26
27
1
User Guide for DC2200
VVGGAA DDiiggiittaall CCaammeerraa DDCC22220000
UUsseerr GGuuiiddee
The package contains of below items :
DC2200 Camera
Program CD
USB cable, 1.5m, transparent
TV cable, 1.2m, black color
Hand Strap
User manual
Alkaline Batteries (3Ax3) are not included
1 unit
1 piece
1 piece
1 piece
1 piece
inside CD-ROM
Mode
VGA
QVGA
2X(Digital)
Movie
Resolution
640x480
320x240
320X240
160 x 120
File Extension
File Size
JPEG ~120KB(Fine),~60KB (Norm)
JPEG
JPEG
MOV
~80KB(Econ)
~45KB
up to 980KB, 25~30s
2
User Guide for DC2200
Electromagnetic Compatibility Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions : (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
Warning : Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If the unit does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
•
• Connect the equipment into an outlet on a circuit different from that to which the
Increase the separation between the equipment and receiver.
receiver is connected.
• Consult the dealer or any experienced TV/radio technician for help.
Trademark acknowledgements
The MyCamera PC/MAC driver is developed by Sound Vision Imaging, USA.
Microsoft, Windows 98,2000,NT,Me are
Corporation.
Pentium is a registered trademark of Intel Corporation.
Macintosh, MAC, iMAC, Quicktime are the registered trademarks of Apple
Computer,Inc.
The Photo Fantasy, Photo Printer and Photo Studio is licensed by Arcsoft, USA.
the registered
trademarks of Microsoft
All other product names mentioned herein are trademarks or registered trademarks of
their respective owners.
3
User Guide for DC2200
Precautions :
Thank you for selecting DC2200 dual mode digital camera. Please read the instructions
carefully for a thorough understanding before taking pictures.
l This camera is not resistant to water and should not be used outdoors in snow or rain.
If accidentally dropped in water, please quickly pour out the water. Let it to dry by
sunlight or by air-blower.
l Protect it from excessive humidity. It will wet the lens and the picture is blur.
l Do not attempt to disassemble the camera yourself. Always take it to an authorized
service facility for repair.
l Remove the battery if you do not expect to use the camera for 1 month or longer.
l When storing the camera, wrap it in a clean, soft cloth and place in a cool, dry, dust-
free place. Also it should not be placed in very hot temperature condition or in direct
sun light.
l The battery may explode or cause burns if disassembled, recharged, shorted, exposed
to high temperature, or disposed of in fire.
l Take care on the lens. Use special cloth to clean it.
l Condensation is a problem when bringing cold equipment into a warm room. Try to
l
put the camera in plastic bag so condensation forms on the outside of the bag.
If nothing at all is displayed in the LCD panel, the battery may be inserted in
opposite polarity.
If the LCD display is damaged, do not touch it.
l
l Taking out the battery will cause the loss of internal memory (not for the CF
card). Make sure you have uploaded the photos to the PC before taking out any
of the batteries.
4
User Guide for DC2200
Battery Used for DC2200 Camera
l To power up the unit, the 3xAAA alkaline batteries should be put in the battery
compartment.
l Press the Power button.
l
If the battery power is taken off, the internal memory is erased and the TV settings will be reset to
default.
• Make sure it is power up by the battery before you connect it to the PC with the USB cable.
• When connected to USB, the unit will not go to standby mode. You can take photo or
movie with USB cable connected to the PC in order to save battery power.
• You cannot take photo with the USB connected to the MAC unit.
The first segment of the battery icon will blink if battery power is too low.
Please change to new alkaline batteries as soon as possible. Always upload the images to
the computer by the time the battery low icon is prompted.
Push off the battery door and place the 3XAAA alkaline battery in correct polarity.
5
User Guide for DC2200
Nomenclature :
6
User Guide for DC2200
Connect the camera unit by USB cable.
1. First, the PC/Mac is installed with the My Camera driver (install the CD-ROM
will put the driver to your PC and double click the Mac driver Installer in the
Mac computer will start to install the My Camera driver ).
2. Then power on the camera unit. You can see the status LCD is on.
3. After connecting the USB cable, ‘PC’ is seen on the right corner of the LCD.
4. The My Camera explorer is placed in the My Computer folder. Double click on it
will open the explorer and you can see the image files.
Connect the PC and the camera with the USB cord.
7