第1页 / 共2222页
第2页 / 共2222页
第3页 / 共2222页
第4页 / 共2222页
第5页 / 共2222页
第6页 / 共2222页
第7页 / 共2222页
第8页 / 共2222页
3G WCDMA标准文件：3GPP TS 34.121-1 version 15.2.0 Release 15.pdf
Intellectual Property Rights
Foreword
Modal verbs terminology
Foreword
Introduction
1 Scope
2 References
3 Definitions, symbols, abbreviations and equations
3.1 Definitions
3.2 Symbols
3.3 Abbreviations
3.4 Equations
4 Frequency bands and channel arrangement
4.1 General
4.2 Frequency bands
4.3 TX-RX frequency separation
4.4 Channel arrangement
4.4.1 Channel spacing
4.4.2 Channel raster
4.4.3 Channel number
4.4.4 UARFCN
4A Reference Conditions
4A.1 Generic setup procedures
4A.2 System information
4A.3 Message contents
4A.4 Measurement configurations
5 Transmitter Characteristics
5.1 General
5.2 Maximum Output Power
5.2.1 Definition and applicability
5.2.2 Minimum Requirements
5.2.3 Test purpose
5.2.4 Method of test
5.2.4.1 Initial conditions
5.2.4.2 Procedure
5.2.5 Test requirements
5.2A Maximum Output Power with HS-DPCCH (Release 5 only)
5.2A.1 Definition and applicability
5.2A.2 Minimum Requirements
5.2A.3 Test purpose
5.2A.4 Method of test
5.2A.4.1 Initial conditions
5.2A.4.2 Procedure
5.2A.5 Test requirements
5.2AA Maximum Output Power with HS-DPCCH (Release 6 and later)
5.2AA.1 Definition and applicability
5.2AA.2 Minimum Requirements
5.2AA.3 Test purpose
5.2AA.4 Method of test
5.2AA.4.1 Initial conditions
5.2AA.4.2 Procedure
5.2AA.5 Test requirements
5.2AB Maximum Output Power for OLTD
5.2AB.1 Definition and applicability
5.2AB.2 Minimum Requirements
5.2AB.3 Test purpose
5.2AB.4 Method of test
5.2AB.4.1 Initial conditions
5.2AB.4.2 Procedure
5.2AB.5 Test requirements
5.2AC Maximum Output Power for UL CLTD activation state 1
5.2AC.1 Definition and applicability
5.2AC.2 Minimum Requirements
5.2AC.3 Test purpose
5.2AC.4 Method of test
5.2AC.4.1 Initial conditions
5.2AC.4.2 Procedure
5.2AC.5 Test requirements
5.2AD Maximum Output Power for UL CLTD activation state 2 and 3
5.2AD.1 Definition and applicability
5.2AD.2 Minimum Requirements
5.2AD.3 Test purpose
5.2AD.4 Method of test
5.2AD.4.1 Initial conditions
5.2AD.4.2 Procedure
5.2AD.5 Test requirements
5.2B Maximum Output Power with HS-DPCCH and E-DCH
5.2B.1 Definition and applicability
5.2B.2 Minimum Requirements
5.2B.3 Test purpose
5.2B.4 Method of test
5.2B.4.1 Initial conditions
5.2B.4.2 Procedure
5.2B.5 Test requirements
5.2BA UE Maximum Output Power for DC-HSUPA (QPSK)
5.2BA.1 Definition and applicability
5.2BA.2 Minimum Requirements
5.2BA.3 Test purpose
5.2BA.4 Method of test
5.2BA.4.1 Initial conditions
5.2BA.4.2 Procedure
5.2BA.5 Test requirements
5.2BB UE Maximum Output Power for DC-HSUPA (16QAM)
5.2BB.1 Definition and applicability
5.2BB.2 Minimum Requirements
5.2BB.3 Test purpose
5.2BB.4 Method of test
5.2BB.4.1 Initial conditions
5.2BB.4.2 Procedure
5.2BB.5 Test requirements
5.2BC Maximum Output Power with HS-DPCCH and E-DCH for OLTD
5.2BD Maximum Output Power with HS-DPCCH and E-DCH for UL CLTD activation state 1
5.2BD.1 Definition and applicability
5.2BD.2 Minimum Requirements
5.2BD.3 Test purpose
5.2BD.4 Method of test
5.2BD.4.1 Initial conditions
5.2BD.4.2 Procedure
5.2BD.4.2.1 Procedure for sub-test 1 to 4
5.2BD.5 Test requirements
5.2BE Maximum Output Power with HS-DPCCH and E-DCH for UL CLTD activation state 2 and 3.
5.2BE.1 Definition and applicability
5.2BE.2 Minimum Requirements
5.2BE.3 Test purpose
5.2BE.4 Method of test
5.2BE.4.1 Initial conditions
5.2BE.4.2 Procedure
5.2BE.4.2.1 Procedure for sub-test 1 to 4
5.2BE.5 Test requirements
5.2C UE relative code domain power accuracy
5.2C.1 Definition and applicability
5.2C.2 Minimum Requirements
5.2C.3 Test purpose
5.2C.4 Method of test
5.2C.4.1 Initial conditions
5.2C.4.2 Procedure
5.2C.5 Test requirements
5.2CA UE relative code domain power accuracy for OLTD
5.2CA.1 Definition and applicability
5.2CA.2 Minimum Requirements
5.2CA.3 Test purpose
5.2CA.4 Method of test
5.2CA.4.1 Initial conditions
5.2CA.4.2 Procedure
5.2CA.5 Test requirements
5.2CB UE relative code domain power accuracy for UL CLTD activation state 1
5.2CB.1 Definition and applicability
5.2CB.2 Minimum Requirements
5.2CB.3 Test purpose
5.2CB.4 Method of test
5.2CB.4.1 Initial conditions
5.2CB.4.2 Procedure
5.2CB.5 Test requirements
5.2CC UE relative code domain power accuracy for UL CLTD activation state 2 and 3
5.2CC.1 Definition and applicability
5.2CC.2 Minimum Requirements
5.2CC.3 Test purpose
5.2CC.4 Method of test
5.2CC.4.1 Initial conditions
5.2CC.4.2 Procedure
5.2CC.5 Test requirements
5.2D UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH
5.2D.1 Definition and applicability
5.2D.2 Minimum Requirements
5.2D.3 Test purpose
5.2D.4 Method of test
5.2D.4.1 Initial conditions
5.2D.4.2 Procedure
5.2D.5 Test requirements
5.2DA UE Relative Code Domain Power Accuracy for DC-HSUPA with QPSK
5.2DA.1 Definition and applicability
5.2DA.2 Minimum Requirements
5.2DA.3 Test purpose
5.2DA.4 Method of test
5.2DA.4.1 Initial conditions
5.2DA.4.2 Procedure
5.2DA.5 Test requirements
5.2DB UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH for OLTD
5.2DB.1 Definition and applicability
5.2DB.2 Minimum Requirements
5.2DB.3 Test purpose
5.2DB.4 Method of test
5.2DB.4.1 Initial conditions
5.2DB.4.2 Procedure
5.2DB.5 Test requirements
5.2DC UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH for UL CLTD activation state 1
5.2DC.1 Definition and applicability
5.2DC.2 Minimum Requirements
5.2DC.3 Test purpose
5.2DC.4 Method of test
5.2DC.4.1 Initial conditions
5.2DC.4.2 Procedure
5.2DC.5 Test requirements
5.2DD UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH for UL CLTD activation state 2 and 3
5.2DD.1 Definition and applicability
5.2DD.2 Minimum Requirements
5.2DD.3 Test purpose
5.2DD.4 Method of test
5.2DD.4.1 Initial conditions
5.2DD.4.2 Procedure
5.2DD.5 Test requirements
5.2E UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM
5.2E.1 Definition and applicability
5.2E.2 Minimum Requirements
5.2E.3 Test purpose
5.2E.4 Method of test
5.2E.4.1 Initial conditions
5.2E.4.2 Procedure
5.2E.5 Test requirements
5.2EA UE Relative Code Domain Power Accuracy for DC-HSUPA with 16QAM
5.2EA.1 Definition and applicability
5.2EA.2 Minimum Requirements
5.2EA.3 Test purpose
5.2EA.4 Method of test
5.2EA.4.1 Initial conditions
5.2EA.4.2 Procedure
5.2EA.5 Test requirements
5.2EB UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM for OLTD
5.2EB.1 Definition and applicability
5.2EB.2 Minimum Requirements
5.2EB.3 Test purpose
5.2EB.4 Method of test
5.2EB.4.1 Initial conditions
5.2EB.4.2 Procedure
5.2EB.5 Test requirements
5.2EC UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM for UL CLTD activation state 1
5.2EC.1 Definition and applicability
5.2EC.2 Minimum Requirements
5.2EC.3 Test purpose
5.2EC.4 Method of test
5.2EC.4.1 Initial conditions
5.2EC.4.2 Procedure
5.2EC.5 Test requirements
5.2ED UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM for UL CLTD activation state 2 and 3
5.2ED.1 Definition and applicability
5.2ED.2 Minimum Requirements
5.2ED.3 Test purpose
5.2ED.4 Method of test
5.2ED.4.1 Initial conditions
5.2ED.4.2 Procedure
5.2ED.5 Test requirements
5.3 Frequency Error
5.3.1 Definition and applicability
5.3.2 Minimum Requirements
5.3.3 Test purpose
5.3.4 Method of test
5.3.4.1 Initial conditions
5.3.4.2 Procedure
5.3.5 Test Requirements
5.3A Frequency Error for DC-HSUPA
5.3A.1 Definition and applicability
5.3A.2 Minimum Requirements
5.3A.3 Test purpose
5.3A.4 Method of test
5.3A.4.1 Initial conditions
5.3A.4.2 Procedure
5.3A.5 Test Requirements
5.3B Frequency Error for OLTD
5.3B.1 Definition and applicability
5.3B.2 Minimum Requirements
5.3B.3 Test purpose
5.3B.4 Method of test
5.3B.4.1 Initial conditions
5.3B.4.2 Procedure
5.3B.5 Test Requirements
5.3C Frequency Error for UL CLTD Activation state 1
5.3C.1 Definition and applicability
5.3C.2 Minimum Requirements
5.3C.3 Test purpose
5.3C.4 Method of test
5.3C.4.1 Initial conditions
5.3C.4.2 Procedure
5.3C.5 Test Requirements
5.3D Frequency Error for UL CLTD Activation state 2 and 3
5.3D.1 Definition and applicability
5.3D.2 Minimum Requirements
5.3D.3 Test purpose
5.3D.4 Method of test
5.3D.4.1 Initial conditions
5.3D.4.2 Procedure
5.3D.5 Test Requirements
5.4 Output Power Dynamics in the Uplink
5.4.1 Open Loop Power Control in the Uplink
5.4.1.1 Definition and applicability
5.4.1.2 Minimum requirements
5.4.1.3 Test purpose
5.4.1.4 Method of test
5.4.1.5 Test requirements
5.4.1A Open Loop Power Control in the Uplink for DC-HSUPA
5.4.1A.1 Definition and applicability
5.4.1A.2 Minimum requirements
5.4.1A.3 Test purpose
5.4.1A.4 Method of test
5.4.1A.5 Test requirements
5.4.2 Inner Loop Power Control in the Uplink
5.4.2.1 Definition and applicability
5.4.2.2 Minimum requirements
5.4.2.3 Test purpose
5.4.2.4 Method of test
5.4.2.5 Test requirements
5.4.2A Inner Loop Power Control in the Uplink for DC-HSUPA
5.4.2A.1 Definition and applicability
5.4.2A.2 Minimum requirements
5.4.2A.3 Test purpose
5.4.2A.4 Method of test
5.4.2A.5 Test requirements
5.4.2B Inner Loop Power Control in the Uplink for OLTD
5.4.2B.1 Definition and applicability
5.4.2B.2 Minimum requirements
5.4.2B.3 Test purpose
5.4.2B.4 Method of test
5.4.2B.4.1 Initial conditions
5.4.2B.4.2 Procedure
5.4.2B.5 Test requirements
5.4.2C Inner Loop Power Control in the Uplink for UL CLTD activation state 1
5.4.2C.1 Definition and applicability
5.4.2C.2 Minimum requirements
5.4.2C.3 Test purpose
5.4.2C.4 Method of test
5.4.2C.4.1 Initial conditions
5.4.2C.4.2 Procedure
5.4.2C.5 Test requirements
5.4.2D Inner Loop Power Control in the Uplink for UL CLTD activation state 2 and 3
5.4.2D.1 Definition and applicability
5.4.2D.2 Minimum requirements
5.4.2D.3 Test purpose
5.4.2D.4 Method of test
5.4.2D.4.1 Initial conditions
5.4.2D.4.2 Procedure
5.4.2D.5 Test requirements
5.4.3 Minimum Output Power
5.4.3.1 Definition and applicability
5.4.3.2 Minimum Requirements
5.4.3.3 Test purpose
5.4.3.4 Method of test
5.4.3.5 Test requirements
5.4.3A Minimum Output Power for DC-HSUPA
5.4.3A.1 Definition and applicability
5.4.3A.2 Minimum Requirements
5.4.3A.3 Test purpose
5.4.3A.4 Method of test
5.4.3A.4.1 Initial conditions
5.4.3A.4.2 Procedure
5.4.3A.5 Test requirements
5.4.3B Minimum Output Power for OLTD
5.4.3B.1 Definition and applicability
5.4.3B.2 Minimum Requirements
5.4.3B.3 Test purpose
5.4.3B.4 Method of test
5.4.3B.4.1 Initial conditions
5.4.3B.4.2 Procedure
5.4.3B.5 Test requirements
5.4.3C Minimum Output Power for UL CLTD Activation state 1
5.4.3C.1 Definition and applicability
5.4.3C.2 Minimum Requirements
5.4.3C.3 Test purpose
5.4.3C.4 Method of test
5.4.3C.4.1 Initial conditions
5.4.3C.4.2 Procedure
5.4.3C.5 Test requirements
5.4.3D Minimum Output Power for UL CLTD Activation state 2 and 3
5.4.3D.1 Definition and applicability
5.4.3D.2 Minimum Requirements
5.4.3D.3 Test purpose
5.4.3D.4 Method of test
5.4.3D.4.1 Initial conditions
5.4.3D.4.2 Procedure
5.4.3D.5 Test requirements
5.4.4 Out-of-synchronisation handling of output power
5.4.4.1 Definition and applicability
5.4.4.2 Minimum Requirements
5.4.4.3 Test purpose
5.4.4.4 Method of test
5.4.4.5 Test requirements
5.4.4A Out-of-synchronization handling of output power for a UE which supports type1 for DCH
5.4.4A.1 Definition and applicability
5.4.4A.2 Minimum requirement
5.4.4A.3 Test purpose
5.4.4A.4 Method of test
5.4.4A.5 Test requirements
5.4.4B Out-of-synchronisation handling of output power for OLTD
5.4.4B.1 Definition and applicability
5.4.4B.2 Minimum Requirements
5.4.4B.3 Test purpose
5.4.4B.4 Method of test
5.4.4B.4.1 Initial conditions
5.4.4B.4.2 Procedure
5.4.4B.5 Test requirements
5.4.4C Out-of-synchronisation handling of output power for UL CLTD activation state 1
5.4.4C.1 Definition and applicability
5.4.4C.2 Minimum Requirements
5.4.4C.3 Test purpose
5.4.4C.4 Method of test
5.4.4C.5 Test requirements
5.4.4D Out-of-synchronisation handling of output power for UL CLTD activation state 2 and 3
5.4.4D.1 Definition and applicability
5.4.4D.2 Minimum Requirements
5.4.4D.3 Test purpose
5.4.4D.4 Method of test
5.4.4D.5 Test requirements
5.4.5 Out of quality handling of TPI for UL CLTD activation state 1
5.4.5.1 Definition and applicability
5.4.5.2 Minimum Requirements
5.4.5.3 Test purpose
5.4.5.4 Method of test
5.4.5.5 Test requirements
5.5 Transmit ON/OFF Power
5.5.1 Transmit OFF Power
5.5.1.1 Definition and applicability
5.5.1.2 Minimum Requirements
5.5.1.3 Test purpose
5.5.1.4 Method of test
5.5.1.5 Test requirements
5.5.2 Transmit ON/OFF Time mask
5.5.2.1 Definition and applicability
5.5.2.2 Minimum requirements
5.5.2.3 Test purpose
5.5.2.4 Method of test
5.5.2.5 Test requirements
5.6 Change of TFC
5.6.1 Definition and applicability
5.6.2 Minimum requirements
5.6.3 Test purpose
5.6.4 Method of test
5.6.5 Test requirements
5.6AA Change of TFC for OLTD
5.6AA.1 Definition and applicability
5.6AA.2 Minimum requirements
5.6AA.3 Test purpose
5.6AA.4 Method of test
5.6AA.4.1 Initial conditions
5.6AA.4.2 Procedure
5.6AA.5 Test requirements
5.6AB Void
5.6AC Void
5.7 Power setting in uplink compressed mode
5.7.1 Definition and applicability
5.7.2 Minimum requirements
5.7.3 Test purpose
5.7.4 Method of test
5.7.5 Test requirements
5.7A HS-DPCCH power control
5.7A.1 Definition and applicability
5.7A.2 Minimum requirement
5.7A.3 Test purpose
5.7A.4 Method of test
5.7A.5 Test requirements
5.7BA HS-DPCCH power control for UL OLTD
5.7BA.1 Definition and applicability
5.7BA.2 Minimum requirement
5.7BA.3 Test purpose
5.7BA.4 Method of test
5.7BA.4.1 Initial conditions
5.7BA.4.2 Procedure
5.7BA.5 Test requirements
5.7BB HS-DPCCH power control for UL CLTD activation state 1
5.7BB.1 Definition and applicability
5.7BB.2 Minimum requirement
5.7BB.3 Test purpose
5.7BB.4 Method of test
5.7BB.4.1 Initial conditions
5.7BB.4.2 Procedure
5.7BB.5 Test requirements
5.7BC HS-DPCCH power control for UL CLTD activation state 2 and 3
5.7BC.1 Definition and applicability
5.7BC.2 Minimum requirement
5.7BC.3 Test purpose
5.7BC.4 Method of test
5.7BC.4.1 Initial conditions
5.7BC.4.2 Procedure
5.7BC.5 Test requirements
5.8 Occupied Bandwidth (OBW)
5.8.1 Definition and applicability
5.8.2 Minimum Requirements
5.8.3 Test purpose
5.8.4 Method of test
5.8.5 Test Requirements
5.8A Occupied Bandwidth (OBW) for DC-HSUPA
5.8A.1 Definition and applicability
5.8A.2 Minimum Requirements
5.8A.3 Test purpose
5.8A.4 Method of test
5.8A.4.1 Initial conditions
5.8A.4.2 Procedure
5.8A.5 Test Requirements
5.8B Occupied Bandwidth (OBW) for OLTD
5.8B.1 Definition and applicability
5.8B.2 Minimum Requirements
5.8B.3 Test purpose
5.8B.4 Method of test
5.8B.4.1 Initial conditions
5.8B.4.2 Procedure
5.8B.5 Test Requirements
5.8C Occupied Bandwidth (OBW) for UL CLTD Activation state 1
5.8C.1 Definition and applicability
5.8C.2 Minimum Requirements
5.8C.3 Test purpose
5.8C.4 Method of test
5.8C.4.1 Initial conditions
5.8C.4.2 Procedure
5.8C.5 Test Requirements
5.9 Spectrum emission mask
5.9.1 Definition and applicability
5.9.2 Minimum Requirements
5.9.3 Test purpose
5.9.4 Method of test
5.9.4.1 Initial conditions
5.9.4.2 Procedure
5.9.5 Test requirements
5.9A Spectrum Emission Mask with HS-DPCCH
5.9A.1 Definition and applicability
5.9A.2 Minimum Requirements
5.9A.3 Test purpose
5.9A.4 Method of test
5.9A.4.1 Initial conditions
5.9A.4.2 Procedure
5.9A.5 Test requirements
5.9AA Spectrum Emission Mask with HS-DPCCH for UL OLTD
5.9AA.1 Definition and applicability
5.9AA.2 Minimum Requirements
5.9AA.3 Test purpose
5.9AA.4 Method of test
5.9AA.4.1 Initial conditions
5.9AA.4.2 Procedure
5.9AA.5 Test requirements
5.9AB Spectrum Emission Mask with HS-DPCCH for UL CLTD activation state 1
5.9AB.1 Definition and applicability
5.9AB.2 Minimum Requirements
5.9AB.3 Test purpose
5.9AB.4 Method of test
5.9AB.4.1 Initial conditions
5.9AB.4.2 Procedure
5.9AB.5 Test requirements
5.9AC Spectrum Emission Mask with HS-DPCCH for UL CLTD activation state 2 and 3
5.9AC.1 Definition and applicability
5.9AC.2 Minimum Requirements
5.9AC.3 Test purpose
5.9AC.4 Method of test
5.9AC.4.1 Initial conditions
5.9AC.4.2 Procedure
5.9AC.5 Test requirements
5.9B Spectrum Emission Mask with E-DCH
5.9B.1 Definition and applicability
5.9B.2 Minimum Requirements
5.9B.3 Test purpose
5.9B.4 Method of test
5.9B.4.1 Initial conditions
5.9B.4.2 Procedure
5.9B.5 Test requirements
5.9BA Spectrum Emission Mask with E-DCH for UL OLTD
5.9BA.1 Definition and applicability
5.9BA.2 Minimum Requirements
5.9BA.3 Test purpose
5.9BA.4 Method of test
5.9BA.4.1 Initial conditions
5.9BA.4.2 Procedure
5.9BA.5 Test requirements
5.9BB Spectrum Emission Mask with E-DCH for UL CLTD activation state 1
5.9BB.1 Definition and applicability
5.9BB.2 Minimum Requirements
5.9BB.3 Test purpose
5.9BB.4 Method of test
5.9BB.4.1 Initial conditions
5.9BB.4.2 Procedure
5.9BB.5 Test requirements
5.9BC Spectrum Emission Mask with E-DCH for UL CLTD activation state 2 and 3
5.9BC.1 Definition and applicability
5.9BC.2 Minimum Requirements
5.9BC.3 Test purpose
5.9BC.4 Method of test
5.9BC.4.1 Initial conditions
5.9BC.4.2 Procedure
5.9BC.5 Test requirements
5.9C Additional Spectrum Emission Mask for DC-HSUPA (QPSK)
5.9C.1 Definition and applicability
5.9C.2 Minimum Requirements
5.9C.3 Test purpose
5.9C.4 Method of test
5.9C.4.1 Initial conditions
5.9C.4.2 Procedure
5.9C.5 Test requirements
5.9D Additional Spectrum Emission Mask for DC-HSUPA (16QAM)
5.9D.1 Definition and applicability
5.9D.2 Minimum Requirements
5.9D.3 Test purpose
5.9D.4 Method of test
5.9D.4.1 Initial conditions
5.9D.4.2 Procedure
5.9D.5 Test requirements
5.10 Adjacent Channel Leakage Power Ratio (ACLR)
5.10.1 Definition and applicability
5.10.2 Minimum Requirements
5.10.3 Test purpose
5.10.4 Method of test
5.10.5 Test requirements
5.10A Adjacent Channel Leakage Power Ratio (ACLR) with HS-DPCCH
5.10A.1 Definition and applicability
5.10A.2 Minimum Requirements
5.10A.3 Test purpose
5.10A.4 Method of test
5.10A.5 Test requirements
5.10AA Adjacent Channel Leakage Power Ratio (ACLR) with HS-DPCCH for OLTD
5.10AA.1 Definition and applicability
5.10AA.2 Minimum Requirements
5.10AA.3 Test purpose
5.10AA.4 Method of test
5.10AA.5 Test requirements
5.10AB Adjacent Channel Leakage Power Ratio (ACLR) with HS-DPCCH for UL CLTD Activation state 1
5.10AB.1 Definition and applicability
5.10AB.2 Minimum Requirements
5.10AB.3 Test purpose
5.10AB.4 Method of test
5.10AB.4.1 Initial conditions
5.10AB.4.2 Procedure
5.10AB.5 Test requirements
5.10AC Adjacent Channel Leakage Power Ratio (ACLR) with HS-DPCCH for UL CLTD Activation state 2 and 3
5.10AC.1 Definition and applicability
5.10AC.2 Minimum Requirements
5.10AC.3 Test purpose
5.10AC.4 Method of test
5.10AC.4.1 Initial conditions
5.10AC.4.2 Procedure
5.10AC.5 Test requirements
5.10B Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH
5.10B.1 Definition and applicability
5.10B.2 Minimum Requirements
5.10B.3 Test purpose
5.10B.4 Method of test
5.10B.5 Test requirements
5.10BA Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH for OLTD
5.10BA.1 Definition and applicability
5.10BA.2 Minimum Requirements
5.10BA.3 Test purpose
5.10BA.4 Method of test
5.10BA.5 Test requirements
5.10BB Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH for UL CLTD Activation state 1
5.10BB.1 Definition and applicability
5.10BB.2 Minimum Requirements
5.10BB.3 Test purpose
5.10BB.4 Method of test
5.10BB.5 Test requirements
5.10BC Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH for UL CLTD Activation state 2 and 3
5.10BC.1 Definition and applicability
5.10BC.2 Minimum Requirements
5.10BC.3 Test purpose
5.10BC.4 Method of test
5.10BC.5 Test requirements
5.10C Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH for DC-HSUPA (QPSK)
5.10C.1 Definition and applicability
5.10C.2 Minimum Requirements
5.10C.3 Test purpose
5.10C.4 Method of test
5.10C.5 Test requirements
5.10D Adjacent Channel Leakage Power Ratio (ACLR) with E-DCH for DC-HSUPA (16QAM)
5.10D.1 Definition and applicability
5.10D.2 Minimum Requirements
5.10D.3 Test purpose
5.10D.4 Method of test
5.10D.5 Test requirements
5.11 Spurious Emissions
5.11.1 Definition and applicability
5.11.2 Minimum Requirements
5.11.3 Test purpose
5.11.4 Method of test
5.11.5 Test requirements
5.11A Spurious Emissions for DC-HSUPA
5.11A.1 Definition and applicability
5.11A.2 Minimum Requirements
5.11A.3 Test purpose
5.11A.4 Method of test
5.11A.5 Test requirements
5.11B Spurious Emissions for UL OLTD
5.11B.1 Definition and applicability
5.11B.2 Minimum Requirements
5.11B.3 Test purpose
5.11B.4 Method of test
5.11B.5 Test requirements
5.11C Spurious Emissions for UL CLTD Activation state 1
5.11C.1 Definition and applicability
5.11C.2 Minimum Requirements
5.11C.3 Test purpose
5.11C.4 Method of test
5.11C.5 Test requirements
5.11D Spurious Emissions for UL CLTD Activation state 2 and 3
5.11D.1 Definition and applicability
5.11D.2 Minimum Requirements
5.11D.3 Test purpose
5.11D.4 Method of test
5.11D.5 Test requirements
5.12 Transmit Intermodulation
5.12.1 Definition and applicability
5.12.2 Minimum Requirements
5.12.3 Test purpose
5.12.4 Method of test
5.12.5 Test requirements
5.12A Transmit Intermodulation for DC-HSUPA
5.12A.1 Definition and applicability
5.12A.2 Minimum Requirements for DC-HSUPA
5.12A.3 Test purpose
5.12A.4 Method of test
5.12A.5 Test requirements
5.13 Transmit Modulation
5.13.1 Error Vector Magnitude (EVM)
5.13.1.1 Definition and applicability
5.13.1.2 Minimum Requirements
5.13.1.3 Test purpose
5.13.1.4 Method of test
5.13.1.5 Test requirements
5.13.1A Error Vector Magnitude (EVM) with HS-DPCCH
5.13.1A.1 Definition and applicability
5.13.1A.2 Minimum Requirements
5.13.1A.3 Test purpose
5.13.1A.4 Method of test
5.13.1A.5 Test requirements
5.13.1AA Error Vector Magnitude (EVM) and phase discontinuity with HS-DPCCH
5.13.1AA.1 Definition and applicability
5.13.1AA.2 Minimum Requirements
5.13.1AA.3 Test purpose
5.13.1AA.4 Method of test
5.13.1AA.5 Test requirements
5.13.1AB Error Vector Magnitude (EVM) and phase discontinuity with HS-DPCCH for OLTD
5.13.1AB.1 Definition and applicability
5.13.1AB.2 Minimum Requirements
5.13.1AB.3 Test purpose
5.13.1AB.4 Method of test
5.13.1AB.5 Test requirements
5.13.1AB Error Vector Magnitude (EVM) and phase discontinuity with HS-DPCCH for OLTD
5.13.1AC Error Vector Magnitude (EVM) and phase discontinuity with HS-DPCCH for UL CLTD Activation state 1
5.13.1AC.1 Definition and applicability
5.13.1AC.2 Minimum Requirements
5.13.1AC.3 Test purpose
5.13.1AC.4 Method of test
5.13.1AC.5 Test requirements
5.13.1AD Error Vector Magnitude (EVM) and phase discontinuity with HS-DPCCH for UL CLTD Activation state 2 and 3
5.13.1AD.1 Definition and applicability
5.13.1AD.2 Minimum Requirements
5.13.1AD.3 Test purpose
5.13.1AD.4 Method of test
5.13.1AD.5 Test requirements
5.13.1AAA EVM and IQ origin offset for HS-DPCCH and E-DCH with 16 QAM
5.13.1AAA.1 Definition and applicability
5.13.1AAA.2 Minimum requirement
5.13.1AAA.3 Test purpose
5.13.1AAA.4 Method of test
5.13.1AAA.5 Test requirements
5.13.2 Peak code domain error
5.13.2.1 Definition and applicability
5.13.2.2 Minimum Requirements
5.13.2.3 Test purpose
5.13.2.4 Method of test
5.13.2.5 Test requirements
5.13.2A.1 Definition and applicability
5.13.2A.2 Minimum Requirements
5.13.2A.3 Test purpose
5.13.2A.4 Method of test
5.13.2B Relative Code Domain Error with HS-DPCCH and E-DCH
5.13.2B.1 Definition and applicability
5.13.2B.2 Minimum Requirements
5.13.2B.3 Test purpose
5.13.2B.4 Method of test
5.13.2B.5 Test requirements
5.13.2BA Relative Code Domain Error with HS-DPCCH and E-DCH for DC-HSUPA
5.13.2BA.1 Definition and applicability
5.13.2BA.2 Minimum Requirements
5.13.2BA.3 Test purpose
5.13.2BA.4 Method of test
5.13.2BA.5 Test requirements
5.13.2C Relative Code Domain Error for HS-DPCCH and E-DCH with 16QAM
5.13.2C.1 Definition and applicability
5.13.2C.2 Minimum Requirements
5.13.2C.3 Test purpose
5.13.2C.4 Method of test
5.13.2CA Relative Code Domain Error for HS-DPCCH and E-DCH with 16QAM for DC-HSUPA
5.13.2CA.1 Definition and applicability
5.13.2CA.2 Minimum Requirements
5.13.2CA.3 Test purpose
5.13.2CA.4 Method of test
5.13.2CA.5 Test requirements
5.13.3 UE phase discontinuity
5.13.3.1 Definition and applicability
5.13.3.2 Minimum requirements
5.13.3.3 Test purpose
5.13.3.4 Method of test
5.13.3.5 Test requirements
5.13.4 PRACH preamble quality
5.13.4.1 Definition and applicability
5.13.4.2 Minimum requirements
5.13.4.3 Test purpose
5.13.4.4 Method of test
5.13.4.5 Test requirements
5.13.5 In-band emission for DC-HSUPA
5.13.5.1 Definition and applicability
5.13.5.2 Minimum Requirements
5.13.5.3 Test purpose
5.13.5.4 Method of test
5.13.5.5 Test requirements
6 Receiver Characteristics
6.1 General
6.1A Reference input power adjustment for a dual band device
6.2 Reference Sensitivity Level
6.2.1 Definition and applicability
6.2.2 Minimum Requirements
6.2.3 Test purpose
6.2.4 Method of test
6.2.5 Test requirements
6.2A Reference Sensitivity Level for DC-HSDPA
6.2A.1 Definition and applicability
6.2A.2 Minimum Requirements
6.2A.3 Test purpose
6.2A.4 Method of test
6.2A.5 Test requirements
6.2B Reference Sensitivity Level for DB-DC-HSDPA
6.2B.1 Definition and applicability
6.2B.2 Minimum Requirements
6.2B.3 Test purpose
6.2B.4 Method of test
6.2B.5 Test requirements
6.2C Reference Sensitivity Level for Single band 4C-HSDPA
6.2C.1 Definition and applicability
6.2C.2 Minimum Requirements
6.2C.3 Test purpose
6.2C.4 Method of test
6.2C.4.2 Procedure
6.2C.5 Test requirements
6.2D Reference Sensitivity Level for Dual band 4C-HSDPA
6.2D.1 Definition and applicability
6.2D.2 Minimum Requirements
6.2D.3 Test purpose
6.2D.4 Method of test
6.2D.5 Test requirements
6.2DA Reference Sensitivity Level for Dual band 4C-HSDPA (3 carrier)
6.2DA.1 Definition and applicability
6.2DA.2 Minimum Requirements
6.2DA.3 Test purpose
6.2DA.4 Method of test
6.2DA.5 Test requirements
6.3 Maximum Input Level
6.3.1 Definition and applicability
6.3.2 Minimum requirements
6.3.3 Test purpose
6.3.4 Method of test
6.3.5 Test requirements
6.3A Maximum Input Level for HS-PDSCH Reception (16QAM)
6.3A.1 Definition and applicability
6.3A.2 Minimum requirements
6.3A.3 Test purpose
6.3A.4 Method of test
6.3A.5 Test requirements
6.3B Maximum Input Level for HS-PDSCH Reception (64QAM)
6.3B.1 Definition and applicability
6.3B.2 Minimum requirements
6.3B.3 Test purpose
6.3B.4 Method of test
6.3B.5 Test requirements
6.3C Maximum Input Level for DC-HSDPA Reception (16QAM)
6.3C.1 Definition and applicability
6.3C.2 Minimum requirements
6.3C.3 Test purpose
6.3C.4 Method of test
6.3C.5 Test requirements
6.3D Maximum Input Level for DC-HSDPA Reception (64QAM)
6.3D.1 Definition and applicability
6.3D.2 Minimum requirements
6.3D.3 Test purpose
6.3D.4 Method of test
6.3D.5 Test requirements
6.3E Maximum Input Level for DB-DC-HSDPA Reception (16QAM)
6.3E.1 Definition and applicability
6.3E.2 Minimum requirements
6.3E.3 Test purpose
6.3E.4 Method of test
6.3E.5 Test requirements
6.3F Maximum Input Level for DB-DC-HSDPA Reception (64QAM)
6.3F.1 Definition and applicability
6.3F.2 Minimum requirements
6.3F.3 Test purpose
6.3F.4 Method of test
6.3F.5 Test requirements
6.3G Maximum Input Level for 4C-HSDPA Reception (16QAM)
6.3G.1 Definition and applicability
6.3G.2 Minimum requirements
6.3G.3 Test purpose
6.3G.4 Method of test
6.3G.5 Test requirements
6.3GA Maximum Input Level for 4C-HSDPA Reception (16QAM) (3 carrier)
6.3GA.1 Definition and applicability
6.3GA.2 Minimum requirements
6.3GA.3 Test purpose
6.3GA.4 Method of test
6.3GA.5 Test requirements
6.3H Maximum Input Level for 4C-HSDPA Reception (64QAM)
6.3H.1 Definition and applicability
6.3H.2 Minimum requirements
6.3H.3 Test purpose
6.3H.4 Method of test
6.3H.5 Test requirements
6.3HA Maximum Input Level for 4C-HSDPA Reception (64QAM) (3 carrier)
6.3HA.1 Definition and applicability
6.3HA.2 Minimum requirements
6.3HA.3 Test purpose
6.3HA.4 Method of test
6.3HA.5 Test requirements
6.4 Adjacent Channel Selectivity (ACS) (Rel-99 and Rel-4)
6.4.1 Definition and applicability
6.4.2 Minimum Requirements
6.4.3 Test purpose
6.4.4 Method of test
6.4.5 Test requirements
6.4A Adjacent Channel Selectivity (ACS) (Rel-5 and later releases)
6.4A.1 Definition and applicability
6.4A.2 Minimum Requirements
6.4A.3 Test purpose
6.4A.4 Method of test
6.4A.5 Test requirements
6.4B Adjacent Channel Selectivity (ACS) for DC-HSDPA
6.4B.1 Definition and applicability
6.4B.2 Minimum Requirements
6.4B.3 Test purpose
6.4B.4 Method of test
6.4B.5 Test requirements
6.4C Adjacent Channel Selectivity (ACS) for DB-DC-HSDPA
6.4C.1 Definition and applicability
6.4C.2 Minimum Requirements
6.4C.3 Test purpose
6.4C.4 Method of test
6.4C.5 Test requirements
6.5 Blocking Characteristics
6.5.1 Definition and applicability
6.5.2 Minimum Requirements
6.5.2.1 Minimum Requirements (In-band blocking)
6.5.2.2 Minimum requirements (Out of-band blocking)
6.5.2.3 Minimum requirements (Narrow band blocking)
6.5.3 Test purpose
6.5.4 Method of test
6.5.5 Test requirements
6.5A Blocking Characteristics for DC-HSDPA
6.5A.1 Definition and applicability
6.5A.2 Minimum Requirements
6.5A.2.1 Minimum Requirements (In-band blocking)
6.5A.2.2 Minimum requirements (Out of-band blocking)
6.5A.2.3 Minimum requirements (Narrow band blocking)
6.5A.3 Test purpose
6.5A.4 Method of test
6.5A.5 Test requirements
6.5B Blocking Characteristics for DB-DC-HSDPA
6.5B.1 Definition and applicability
6.5B.2 Minimum Requirements
6.5B.2.1 Minimum Requirements (In-band blocking)
6.5B.2.2 Minimum requirements (Out of-band blocking)
6.5B.2.3 Minimum requirements (Narrow band blocking)
6.5B.3 Test purpose
6.5B.4 Method of test
6.5B.5 Test requirements
6.5C Blocking Characteristics for DC-HSUPA
6.5C.1 Definition and applicability
6.5C.2 Minimum Requirements
6.5C.2.1 Minimum Requirements (In-band blocking)
6.5C.2.2 Minimum requirements (Narrow band blocking)
6.5C.3 Test purpose
6.5C.4 Method of test
6.5C.5 Test requirements
6.5D Blocking Characteristics for single Uplink Single band 4C-HSDPA
6.5D.1 Definition and applicability
6.5D.2 Minimum Requirements
6.5D.2.1 Minimum Requirements (In-band blocking)
6.5D.2.2 Minimum requirements (Out of-band blocking)
6.5D.3 Test purpose
6.5D.4 Method of test
6.5D.4.1 Initial conditions
6.5D.4.2 Procedure
6.5D.5 Test requirements
6.5E Blocking Characteristics for dual uplink single band 4C-HSDPA
6.5E.1 Definition and applicability
6.5E.2 Minimum Requirements
6.5E.2.1 Minimum Requirements (In-band blocking)
6.5E.3 Test purpose
6.5E.4 Method of test
6.5E.4.1 Initial conditions
6.5E.4.2 Procedure
6.5E.5 Test requirements
6.5F Blocking Characteristics for single Uplink dual band 4C-HSDPA
6.5F.1 Definition and applicability
6.5F.2 Minimum Requirements
6.5F.2.1 Minimum Requirements (In-band blocking)
6.5F.2.2 Minimum requirements (Out of-band blocking)
6.5F.2.3 Minimum requirements (Narrow band blocking)
6.5F.3 Test purpose
6.5F.4 Method of test
6.5F.4.1 Initial conditions
6.5F.4.2 Procedure
6.5F.5 Test requirements
6.5FA Blocking Characteristics for single Uplink dual band 4C-HSDPA (3 carrier)
6.5FA.1 Definition and applicability
6.5FA.2 Minimum Requirements
6.5FA.2.1 Minimum Requirements (In-band blocking)
6.5FA.2.2 Minimum requirements (Out of-band blocking)
6.5FA.2.3 Minimum requirements (Narrow band blocking)
6.5FA.3 Test purpose
6.5FA.4 Method of test
6.5FA.4.1 Initial conditions
6.5FA.4.2 Procedure
6.5FA.5 Test requirements
6.5G Blocking Characteristics for dual uplink dual band 4C-HSDPA
6.5G.1 Definition and applicability
6.5G.2 Minimum Requirements
6.5G.2.1 Minimum Requirements (In-band blocking)
6.5G.2.2 Minimum requirements (Narrow band blocking)
6.5G.3 Test purpose
6.5G.4 Method of test
6.5G.5 Test requirements
6.5GA Blocking Characteristics for dual uplink dual band 4C-HSDPA (3 carrier)
6.5GA.1 Definition and applicability
6.5GA.2 Minimum Requirements
6.5GA.2.1 Minimum Requirements (In-band blocking)
6.5GA.2.2 Minimum requirements (Narrow band blocking)
6.5GA.3 Test purpose
6.5GA.4 Method of test
6.5GA.5 Test requirements
6.6 Spurious Response
6.6.1 Definition and applicability
6.6.2 Minimum Requirements
6.6.3 Test purpose
6.6.4 Method of test
6.6.5 Test requirements
6.6A Spurious Response for DC-HSDPA
6.6A.1 Definition and applicability
6.6A.2 Minimum Requirements
6.6A.3 Test purpose
6.6A.4 Method of test
6.6A.5 Test requirements
6.6B Spurious Response for DB-DC-HSDPA
6.6B.1 Definition and applicability
6.6B.2 Minimum Requirements
6.6B.3 Test purpose
6.6B.4 Method of test
6.6B.5 Test requirements
6.6C Spurious Response for single band 4C-HSDPA
6.6C.1 Definition and applicability
6.6C.2 Minimum Requirements
6.6C.3 Test purpose
6.6C.4 Method of test
6.6C.5 Test requirements
6.6D Spurious Response for dual band 4C-HSDPA
6.6D.1 Definition and applicability
6.6D.2 Minimum Requirements
6.6D.3 Test purpose
6.6D.4 Method of test
6.6D.5 Test requirements
6.6DA Spurious Response for dual band 4C-HSDPA (3 carrier)
6.6DA.1 Definition and applicability
6.6DA.2 Minimum Requirements
6.6DA.3 Test purpose
6.6DA.4 Method of test
6.6DA.5 Test requirements
6.7 Intermodulation Characteristics
6.7.1 Definition and applicability
6.7.2 Minimum Requirements
6.7.3 Test purpose
6.7.4 Method of test
6.7.5 Test requirements
6.7A Intermodulation Characteristics for DC-HSDPA
6.7A.1 Definition and applicability
6.7A.2 Minimum Requirements
6.7A.3 Test purpose
6.7A.4 Method of test
6.7A.5 Test requirements
6.7B Intermodulation Characteristics for DB-DC-HSDPA
6.7B.1 Definition and applicability
6.7B.2 Minimum Requirements
6.7B.3 Test purpose
6.7B.4 Method of test
6.7B.5 Test requirements
6.7C Intermodulation Characteristics for DC-HSUPA
6.7C.1 Definition and applicability
6.7C.2 Minimum Requirements
6.7C.3 Test purpose
6.7C.4 Method of test
6.7C.5 Test requirements
6.7D Intermodulation Characteristics for single uplink single band 4C-HSDPA
6.7D.1 Definition and applicability
6.7D.2 Minimum Requirements
6.7D.3 Test purpose
6.7D.4 Method of test
6.7D.5 Test requirements
6.7E Intermodulation Characteristics for single uplink dual band 4C-HSDPA
6.7E.1 Definition and applicability
6.7E.2 Minimum Requirements
6.7E.3 Test purpose
6.7E.4 Method of test
6.7E.5 Test requirements
6.7EA Intermodulation Characteristics for single uplink dual band 4C-HSDPA (3 carrier)
6.7EA.1 Definition and applicability
6.7EA.2 Minimum Requirements
6.7EA.3 Test purpose
6.7EA.4 Method of test
6.7EA.5 Test requirements
6.8 Spurious Emissions
6.8.1 Definition and applicability
6.8.2 Minimum Requirements
6.8.3 Test purpose
6.8.4 Method of test
6.8.5 Test requirements
6.8A Spurious Emissions for DB-DC-HSDPA
6.8A.1 Definition and applicability
6.8A.2 Minimum Requirements
6.8A.3 Test purpose
6.8A.4 Method of test
6.8A.5 Test requirements
7 Performance requirements
7.1 General
7.1.1 Measurement Configurations
7.1.2 Definition of Additive White Gaussian Noise (AWGN) Interferer
7.2 Demodulation in Static Propagation conditions
7.2.1 Demodulation of Dedicated Channel (DCH)
7.2.1.1 Definition and applicability
7.2.1.2 Minimum requirements
7.2.1.3 Test purpose
7.2.1.4 Method of test
7.2.1.5 Test requirements
7.2.2 Demodulation of Dedicated Channel (DCH) when (DL_DCH_FET_Config) is configured by higher layers
7.2.2.1 Definition and applicability
7.2.2.2 Minimum requirements
7.2.2.3 Test purpose
7.2.2.4 Method of test
7.2.2.4.1 Initial conditions
7.2.2.4.2 Procedures
7.2.2.5 Test requirements
7.3 Demodulation of DCH in Multi-path Fading Propagation conditions
7.3.1 Single Link Performance
7.3.1.1 Definition and applicability
7.3.1.2 Minimum requirements
7.3.1.3 Test purpose
7.3.1.4 Method of test
7.3.1.5 Test requirements
7.3.2 Single Link Performance when (DL_DCH_FET_Config) is configured by higher layers
7.3.2.1 Definition and applicability
7.3.2.2 Minimum requirements
7.3.2.3 Test purpose
7.3.2.4 Method of test
7.3.2.4.1 Initial conditions
7.3.2.5 Test requirements
7.4 Demodulation of DCH in Moving Propagation conditions
7.4.1 Single Link Performance
7.4.1.1 Definition and applicability
7.4.1.2 Minimum requirements
7.4.1.3 Test purpose
7.4.1.4 Method of test
7.4.1.5 Test requirements
7.5 Demodulation of DCH in Birth-Death Propagation conditions
7.5.1 Single Link Performance
7.5.1.1 Definition and applicability
7.5.1.2 Minimum requirements
7.5.1.3 Test purpose
7.5.1.4 Method of test
7.5.1.5 Test requirements
7.5A Demodulation of DCH in high speed train condition
7.5A.1 Single Link Performance
7.5A.1.1 Definition and applicability
7.5A.1.2 Minimum requirement
7.5A.1.3 Test purpose
7.5A.1.4 Method of test
7.5A.1.5 Test requirements
7.6 Demodulation of DCH in downlink Transmit diversity modes
7.6.1 Demodulation of DCH in open-loop transmit diversity mode
7.6.1.1 Definition and applicability
7.6.1.2 Minimum requirements
7.6.1.3 Test purpose
7.6.1.4 Method of test
7.6.1.5 Test Requirements
7.6.2 Demodulation of DCH in closed loop transmit diversity mode
7.6.2.1 Definition and applicability
7.6.2.2 Minimum requirements
7.6.2.3 Test purpose
7.6.2.4 Method of test
7.6.2.5 Test Requirements
7.6.3 Demodulation of DCH in Site Selection Diversity Transmission Power Control mode
7.6.3.1 Definition and applicability
7.6.3.2 Minimum requirements
7.6.3.3 Test purpose
7.6.3.4 Method of test
7.6.3.5 Test Requirements
7.7 Demodulation in Handover conditions
7.7.1 Demodulation of DCH in Inter-Cell Soft Handover (Release 5 and earlier)
7.7.1.1 Definition and applicability
7.7.1.2 Minimum requirements
7.7.1.3 Test purpose
7.7.1.4 Method of test
7.7.1.5 Test requirements
7.7.1A Demodulation of DCH in Inter-Cell Soft Handover (Release 6 and later)
7.7.1A.1 Definition and applicability
7.7.1A.2 Minimum requirements
7.7.1A.3 Test purpose
7.7.1A.4 Method of test
7.7.1A.5 Test requirements
7.7.1B Demodulation of DCH in Inter-Cell Soft Handover when (DL_DCH_FET_Config) is configured by higher layers
7.7.1B.1 Definition and applicability
7.7.1B.2 Minimum requirements
7.7.1B.3 Test purpose
7.7.1B.4 Method of test
7.7.1B.4.1 Initial conditions
7.7.1B.4.2 Procedures
7.7.1B.5 Test requirements
7.7.2 Combining of TPC commands from radio links of different radio link sets
7.7.2.1 Definition and applicability
7.7.2.2 Minimum requirements
7.7.2.3 Test purpose
7.7.2.4 Method of test
7.7.2.5 Test requirements
7.7.2A Combining of TPC commands from radio links of different radio link sets when (DL_DCH_FET_Config) is configured by higher
7.7.2A.1 Definition and applicability
The requirements and this test apply to release 12 and later releases for all types of UTRA for the FDD UE that support DCH Enh
7.7.2A.3 Test purpose
7.7.2A.4 Method of test
7.7.2A.4.1 Initial conditions
7.7.2A.4.2 Procedures
7.7.2A.5 Test requirements
7.7.3 Combining of reliable TPC commands from radio links of different radio link sets
7.7.3.1 Definition and applicability
7.7.3.2 Minimum requirements
7.7.3.3 Test purpose
7.7.3.4 Method of test
7.7.3.4.1 Test 1 Initial conditions
7.7.3.4.2 Test 1 Procedures
7.7.3.4.3 Test 2 Initial conditions
7.7.3.4.4 Test 2 Procedures
7.7.3.5 Test requirements
7.7.3A Combining of reliable TPC commands from radio links of different radio link sets when DL_DCH_FET_Config [10] is configur
7.7.3A.1 Definition and applicability
7.7.3A.2 Minimum requirements
7.7.3A.3 Test purpose
7.7.3A.4 Method of test
7.7.3A.4.1 Test 1 Initial conditions
7.7.3A.4.2 Test 1 Procedures
7.7.3A.4.3 Test 2 Initial conditions
7.7.3A.4.4 Test 2 Procedures
7.7.3A.5 Test requirements
7.8 Power control in downlink
7.8.1 Power control in the downlink, constant BLER target (Release 5 and earlier)
7.8.1.1 Definition and applicability
7.8.1.2 Minimum requirements
7.8.1.3 Test purpose
7.8.1.4 Method of test
7.8.1.5 Test Requirements
7.8.1A Power control in the downlink, constant BLER target (Release 6 and later)
7.8.1A.1 Definition and applicability
7.8.1A.2 Minimum requirements
7.8.1A.3 Test purpose
7.8.1A.4 Method of test
7.8.1A.5 Test Requirements
7.8.1B Power control in the downlink, constant BLER target when DL_DCH_FET_Config is configured by higher layers
7.8.1B.1 Definition and applicability
7.8.1B.2 Minimum requirements
7.8.1B.3 Test purpose
7.8.1B.4 Method of test
7.8.1B.5 Test Requirements
7.8.2 Power control in the downlink, initial convergence
7.8.2.1 Definition and applicability
7.8.2.2 Minimum requirements
7.8.2.3 Test purpose
7.8.2.4 Method of test
7.8.2.5 Test Requirements
7.8.2A Power control in the downlink, initial convergence when DL_DCH_FET_Config is configured by higher layers
7.8.2A.1 Definition and applicability
7.8.2A.2 Minimum requirements
7.8.2A.3 Test purpose
7.8.2A.4 Method of test
7.8.2A.5 Test Requirements
7.8.3 Power control in the downlink, wind up effects (Release 5 and earlier)
7.8.3.1 Definition and applicability
7.8.3.2 Minimum requirements
7.8.3.3 Test purpose
7.8.3.4 Method of test
7.8.3.5 Test Requirements
7.8.3A Power control in the downlink, wind up effects (Release 6 and later)
7.8.3A.1 Definition and applicability
7.8.3A.2 Minimum requirements
7.8.3A.3 Test purpose
7.8.3A.4 Method of test
7.8.3B Power control in the downlink, wind up effects (Release 6 and later) when DL_DCH_FET_Config is configured by higher laye
7.8.3B.1 Definition and applicability
7.8.3B.2 Minimum requirements
7.8.3B.3 Test purpose
7.8.3B.4 Method of test
7.8.3B.4.1 Initial conditions
7.8.3B.4.2 Procedure
7.8.3B.5 Test Requirements
7.8.4 Power control in the downlink, different transport formats
7.8.4.1 Definition and applicability
7.8.4.2 Minimum requirements
7.8.4.3 Test purpose
7.8.4.4 Method of test
7.8.4.5 Test Requirements
7.8.4A Power control in the downlink, different transport formats when DL_DCH_FET_Config is configured by higher layers
7.8.4A.1 Definition and applicability
7.8.4A.2 Minimum requirements
7.8.4A.3 Test purpose
7.8.4A.4 Method of test
7.8.4A.4.1 Initial conditions
7.8.4A.4.2 Procedure
7.8.4.5 Test Requirements
7.8.5 Power control in the downlink for F-DPCH
7.8.5.1 Definition and applicability
7.8.5.2 Minimum requirements
7.8.5.3 Test purpose
7.8.5.4 Method of test
7.8.5.5 Test Requirements
7.9 Downlink compressed mode
7.9.1 Single link performance (Release 5 and earlier)
7.9.1.1 Definition and applicability
7.9.1.2 Minimum requirements
7.9.1.3 Test purpose
7.9.1.4 Method of test
7.9.1.5 Test requirements
7.9.1A Single link performance (Release 6 and later)
7.9.1A.1 Definition and applicability
7.9.1A.2 Minimum requirements
7.9.1A.3 Test purpose
7.9.1A.4 Method of test
7.9.1A.5 Test requirements
7.10 Blind transport format detection
7.10.1 Definition and applicability
7.10.2 Minimum requirements
7.10.3 Test purpose
7.10.4 Method of test
7.10.5 Test requirements
7.11 Demodulation of Paging Channel (PCH)
7.11.1 Definition and applicability
7.11.2 Minimum requirements
7.11.3 Test purpose
7.11.4 Method of test
7.11.5 Test requirements
7.12 Detection of Acquisition Indicator (AI)
7.12.1 Definition and applicability
7.12.2 Minimum requirements
7.12.3 Test purpose
7.12.4 Method of test
7.12.5 Test requirements
7.12A Detection of E-DCH Acquisition Indicator (E-AI)
7.12A.1 Definition and applicability
7.12A.2 Minimum requirements
7.12A.3 Test purpose
7.12A.4 Method of test
7.12A.5 Test requirements
7.13 UE UL power control operation with discontinuous UL DPCCH transmission operation
7.13.1 Definition and applicability
7.13.2 Minimum requirement
7.13.3 Test purpose
7.13.4 Method of test
7.13.4.1 Initial conditions
7.13.4.2 Procedure
7.13.5. Test Requirements
8 Requirements for support of RRM
8.1 General
8.1.1 Definition of Additive White Gaussian Noise (AWGN) Interferer
8.1.2 Groups of E-UTRA bands
8.2 Idle Mode Tasks
8.2.1 Cell Selection
8.2.2 Cell Re-Selection
8.2.2.1 Scenario 1: Single carrier case
8.2.2.1.1 Definition and applicability
8.2.2.1.2 Minimum requirement
8.2.2.1.3 Test purpose
8.2.2.1.4 Method of test
8.2.2.1.5 Test requirements
8.2.2.2 Scenario 2: Multi carrier case
8.2.2.2.1 Definition and applicability
8.2.2.2.2 Minimum requirement
8.2.2.2.3 Test purpose
8.2.2.2.4 Method of test
8.2.2.2.5 Test requirements
8.2.3 UTRAN to GSM Cell Re-Selection
8.2.3.1 Scenario 1: Both UTRA and GSM level changed
8.2.3.1.1 Definition and applicability
8.2.3.1.2 Minimum requirement
8.2.3.1.3 Test purpose
8.2.3.1.4 Method of test
8.2.3.1.5 Test requirements
8.2.3.2 Scenario 2: Only UTRA level changed
8.2.3.2.1 Definition and applicability
8.2.3.2.2 Minimum requirement
8.2.3.2.3 Test purpose
8.2.3.2.4 Method of test
8.2.3.2.5 Test requirements
8.2.3.3 Scenario 3: HCS with only UTRA level changed
8.2.3.3.1 Definition and applicability
8.2.3.3.2 Minimum requirement
8.2.3.3.3 Test purpose
8.2.3.3.4 Method of test
8.2.3.3.5 Test requirements
8.2.4 FDD/TDD Cell Re-selection
8.2.4.1 Definition and applicability
8.2.4.1.1 3.84 Mcps TDD Option
8.2.4.1.2 1.28 Mcps TDD Option
8.2.4.2 Minimum requirement
8.2.4.3 Test purpose
8.2.4.4 Method of test
8.2.4.4.1 Initial conditions
8.2.4.4.1.1 3.84 Mcps TDD Option
8.2.4.4.1.2 1.28Mcps TDD Option
8.2.4.4.2 Procedures
8.2.4.5 Test requirements
8.2.5 UTRAN to E-UTRA Cell Re-Selection
8.2.5.1 E-UTRA is of higher priority
8.2.5.1.1 Definition and applicability
8.2.5.1.2 Minimum requirement
8.2.5.1.3 Test purpose
8.2.5.1.4 Method of test
8.2.5.1.5 Test requirements
8.2.5.2 E-UTRA is of lower priority
8.2.5.2.1 Definition and applicability
8.2.5.2.2 Minimum requirement
8.2.5.2.3 Test purpose
8.2.5.2.4 Method of test
8.2.5.2.5 Test requirements
8.2.5.3 RSRQ based reselection when E-UTRA FDD is of higher priority
8.2.5.3.1 Definition and applicability
8.2.5.3.2 Minimum requirement
8.2.5.3.3 Test purpose
8.2.5.3.4 Method of test
8.2.5.3.5 Test requirements
8.3 UTRAN Connected Mode Mobility
8.3.1 FDD/FDD Soft Handover
8.3.1.1 Definition and applicability
8.3.1.2 Minimum requirement
8.3.1.3 Test purpose
8.3.1.4 Method of test
8.3.1.5 Test requirements
8.3.2 FDD/FDD Hard Handover
8.3.2.1 FDD/FDD Hard Handover to intra-frequency cell
8.3.2.1.1 Definition and applicability
8.3.2.1.2 Minimum requirement
8.3.2.1.3 Test purpose
8.3.2.1.4 Method of test
8.3.2.1.5 Test requirements
8.3.2.2 FDD/FDD Hard Handover to inter-frequency cell
8.3.2.2.1 Definition and applicability
8.3.2.2.2 Minimum requirement
8.3.2.2.3 Test purpose
8.3.2.2.4 Method of test
8.3.2.2.5 Test requirements
8.3.3 FDD/TDD Handover
8.3.3.1 Definition and applicability
8.3.3.2 Minimum requirement
8.3.3.3 Test purpose
8.3.3.4 Method of test
8.3.3.5 Test requirements
8.3.4 Inter-system Handover from UTRAN FDD to GSM
8.3.4.1 Definition and applicability
8.3.4.2 Minimum requirement
8.3.4.3 Test purpose
8.3.4.4 Method of test
8.3.4.5 Test requirements
8.3.4a Inter-system Handover from UTRAN FDD to E-UTRAN FDD
8.3.4a.1 Definition and applicability
8.3.4a.2 Minimum requirement
8.3.4a.3 Test purpose
8.3.4a.4 Method of test
8.3.4a.5 Test requirements
8.3.4b Inter-system Handover from UTRAN FDD to E-UTRAN TDD
8.3.4b.1 Definition and applicability
8.3.4b.2 Minimum requirement
8.3.4b.3 Test purpose
8.3.4b.4 Method of test
8.3.4b.4.1 Initial conditions
8.3.4b.4.2 Procedure
8.3.4b.5 Test requirements
8.3.4c Inter-system Handover from UTRAN FDD to E-UTRAN FDD: Unknown Target Cell
8.3.4c.1 Definition and applicability
8.3.4c.2 Minimum requirement
8.3.4c.3 Test purpose
8.3.4c.4 Method of test
8.3.4c.5 Test requirements
8.3.4d Inter-system Handover from UTRAN FDD to E-UTRAN TDD; Unknown Target Cell
8.3.4d.1 Definition and applicability
8.3.4d.2 Minimum requirement
8.3.4d.3 Test purpose
8.3.4d.4 Method of test
8.3.4d.4.1 Initial conditions
8.3.4d.4.2 Procedure
8.3.4d.5 Test requirements
8.3.5 Cell Re-selection in CELL_FACH
8.3.5.1 One frequency present in neighbour lis and FACH measurement occasions configured
8.3.5.1.1 Definition and applicability
8.3.5.1.2 Minimum requirements
8.3.5.1.3 Test purpose
8.3.5.1.4 Method of test
8.3.5.1.5 Test requirements
8.3.5.1a One frequency present in neighbour list and HS-DSCH DRX configured
8.3.5.1a.1 Definition and applicability
8.3.5.1a.2 Minimum requirements
8.3.5.1a.3 Test purpose
8.3.5.1a.4 Method of test
8.3.5.1a.5 Test requirements
8.3.5.2 Two frequencies present in the neighbour list and FACH measurement occasions configured
8.3.5.2.1 Definition and applicability
8.3.5.2.2 Minimum requirements
8.3.5.2.3 Test purpose
8.3.5.2.4 Method of test
8.3.5.2.5 Test requirements
8.3.5.2a Two frequencies present in the neighbour list and HS-DSCH DRX configured (Absolute priority levels not configured)
8.3.5.2a.1 Definition and applicability
8.3.5.2a.2 Minimum requirements
8.3.5.2a.3 Test purpose
8.3.5.2a.4 Method of test
8.3.5.2a.5 Test requirements
8.3.5.2b Two frequencies present in the neighbour list and HS-DSCH DRX configured (Absolute priority levels configured)
8.3.5.2b.1 Definition and applicability
8.3.5.2b.2 Minimum requirements
8.3.5.2b.3 Test purpose
8.3.5.2b.4 Method of test
8.3.5.2b.5 Test requirements
8.3.5.2c Two frequencies present in the neighbour list and HS-DSCH 2nd DRX configured (Absolute priority levels not configured)
8.3.5.2c.1 Definition and applicability
8.3.5.2c.2 Minimum requirements
8.3.5.2c.3 Test purpose
8.3.5.2c.4 Method of test
8.3.5.2c.5 Test requirements
8.3.5.2d Two frequencies present in the neighbour list and HS-DSCH 2nd DRX configured (Absolute priority levels configured)
8.3.5.2d.1 Definition and applicability
8.3.5.2d.2 Minimum requirements
8.3.5.2d.3 Test purpose
8.3.5.2d.4 Method of test
8.3.5.2d.5 Test requirements
8.3.5.3 Cell Reselection to GSM
8.3.5.3.1 Definition and applicability
8.3.5.3.2 Minimum requirements
8.3.5.3.3 Test purpose
8.3.5.3.4 Method of test
8.3.5.3.5 Test requirements
8.3.5.4 Cell Reselection during an MBMS session, two frequencies present in neighbour list
8.3.5.4.1 Definition and applicability
8.3.5.4.2 Minimum requirements
8.3.5.4.3 Test purpose
8.3.5.4.4 Method of test
8.3.5.4.5 Test requirements
8.3.5.5 UTRAN to E-UTRA Cell Reselection
8.3.5.5.1 Reselection to E-UTRA FDD when HS-DSCH DRX is configured (E-UTRA has higher priority)
8.3.5.5.1.1 Definition and applicability
8.3.5.5.1.1 Minimum requirements
8.3.5.5.1.3 Test purpose
8.3.5.5.1.4 Method of test
8.3.5.5.1.4.1 Initial conditions
8.3.5.5.1.4.2 Procedure
8.3.5.5.1.5 Test requirements
8.3.5.5.2 Reselection to E-UTRA FDD when HS-DSCH DRX is configured (E-UTRA has lower priority)
8.3.5.5.2.1 Definition and applicability
8.3.5.5.2.1 Minimum requirements
8.3.5.5.2.3 Test purpose
8.3.5.5.2.4 Method of test
8.3.5.5.2.4.1 Initial conditions
8.3.5.5.2.4.2 Procedure
8.3.5.5.2.5 Test requirements
8.3.5.5.3 Reselection to E-UTRA FDD when HS-DSCH 2nd DRX is configured (E-UTRA has higher priority)
8.3.5.5.3.1 Definition and applicability
8.3.5.5.3.1 Minimum requirements
8.3.5.5.3.3 Test purpose
8.3.5.5.3.4 Method of test
8.3.5.5.3.4.1 Initial conditions
8.3.5.5.3.4.2 Procedure
8.3.5.5.1.5 Test requirements
8.3.5.5.4 Reselection to E-UTRA TDD when HS-DSCH DRX is configured (E-UTRA has higher priority)
8.3.5.5.4.1 Definition and applicability
8.3.5.5.4.1 Minimum requirements
8.3.5.5.4.3 Test purpose
8.3.5.5.4.4 Method of test
8.3.5.5.4.4.1 Initial conditions
8.3.5.5.4.4.2 Procedure
8.3.5.5.4.5 Test requirements
8.3.5.5.5 Reselection to E-UTRA TDD when HS-DSCH DRX is configured (E-UTRA has lower priority)
8.3.5.5.5.1 Definition and applicability
8.3.5.5.5.1 Minimum requirements
8.3.5.5.5.3 Test purpose
8.3.5.5.5.4 Method of test
8.3.5.5.5.4.1 Initial conditions
8.3.5.5.5.4.2 Procedure
8.3.5.5.5.5 Test requirements
8.3.5.5.6 Reselection to E-UTRA TDD when HS-DSCH 2nd DRX is configured (E-UTRA has higher priority)
8.3.5.5.6.1 Definition and applicability
8.3.5.5.6.2 Minimum requirements
8.3.5.5.6.3 Test purpose
8.3.5.5.6.4 Method of test
8.3.5.5.6.4.1 Initial conditions
8.3.5.5.6.4.2 Procedure
8.3.5.5.6.5 Test requirements
8.3.6 Cell Re-selection in CELL_PCH
8.3.6.1 One frequency present in the neighbour list
8.3.6.1.1 Definition and applicability
8.3.6.1.2 Minimum requirements
8.3.6.1.3 Test purpose
8.3.6.1.4 Method of test
8.3.6.1.5 Test requirements
8.3.6.2 Two frequencies present in the neighbour list
8.3.6.2.1 Definition and applicability
8.3.6.2.2 Minimum requirement
8.3.6.2.3 Test purpose
8.3.6.2.4 Method of test
8.3.6.2.5 Test requirements
8.3.6.3 Cell re-selection during an MBMS session, one UTRAN inter-frequency and 2 GSM cells present in the neighbour list
8.3.6.3.1 Definition and applicability
8.3.6.3.2 Minimum requirement
8.3.6.3.3 Test purpose
8.3.6.3.4 Method of test
8.3.6.3.5 Test requirements
8.3.7 Cell Re-selection in URA_PCH
8.3.7.1 One frequency present in the neighbour list
8.3.7.1.1 Definition and applicability
8.3.7.1.2 Minimum requirement
8.3.7.1.3 Test purpose
8.3.7.1.4 Method of test
8.3.7.1.5 Test requirements
8.3.7.2 Two frequencies present in the neighbour list
8.3.7.2.1 Definition and applicability
8.3.7.2.2 Minimum requirement
8.3.7.2.3 Test purpose
8.3.7.2.4 Method of test
8.3.7.2.5 Test requirements
8.3.8 Serving HS-DSCH cell change
8.3.8.1 Definition and applicability
8.3.8.2 Minimum requirement
8.3.8.3 Test purpose
8.3.8.4 Method of test
8.3.8.4.1 Initial conditions
8.3.8.4.2 Procedure
8.3.8.5 Test requirements
8.3.9 Enhanced Serving HS-DSCH cell change
8.3.9.1 Definition and applicability
8.3.9.2 Minimum requirement
8.3.9.3 Test purpose
8.3.9.4 Method of test
8.3.9.4.1 Initial conditions
8.3.9.4.2 Procedure
8.3.9.5 Test requirements
8.3.10 System information acquisition for CSG cell
8.3.10.1 Intrafrequency System information acquisition for CSG cell
8.3.10.1.1 Definition and applicability
8.3.10.1.2 Minimum requirement
8.3.10.1.3 Test purpose
8.3.10.1.4 Method of test
8.3.10.1.5 Test requirements
8.3.10.2 Inter frequency System information acquisition for CSG cell
8.3.10.2.1 Definition and applicability
8.3.10.2.2 Minimum requirement
8.3.10.2.3 Test purpose
8.3.10.2.4 Method of test
8.3.10.2.5 Test requirements
8.4 RRC Connection Control
8.4.1 RRC Re-establishment delay
8.4.1.1 Test 1
8.4.1.1.1 Definition and applicability
8.4.1.1.2 Minimum requirement
8.4.1.1.3 Test purpose
8.4.1.1.4 Method of test
8.4.1.1.5 Test requirements
8.4.1.2 Test 2
8.4.1.2.1 Definition and applicability
8.4.1.2.2 Minimum requirement
8.4.1.2.3 Test purpose
8.4.1.2.4 Method of test
8.4.1.2.5 Test requirements
8.4.2 Random Access
8.4.2.1 Correct behaviour when receiving an ACK (Release 5 and earlier)
8.4.2.1.1 Definition and applicability
8.4.2.1.2 Minimum Requirements
8.4.2.1.3 Test purpose
8.4.2.1.4 Method of test
8.4.2.1.5 Test requirements
8.4.2.1A Correct behaviour when receiving an ACK (Release 6 and later)
8.4.2.1A.1 Definition and applicability
8.4.2.1A.2 Minimum Requirements
8.4.2.1A.3 Test purpose
8.4.2.1A.4 Method of test
8.4.2.1A.5 Test requirements
8.4.2.2 Correct behaviour when receiving an NACK
8.4.2.2.1 Definition and applicability
8.4.2.2.2 Minimum Requirements
8.4.2.2.3 Test purpose
8.4.2.2.4 Method of test
8.4.2.2.5 Test requirements
8.4.2.3 Correct behaviour at Time-out
8.4.2.3.1 Definition and applicability
8.4.2.3.2 Minimum Requirements
8.4.2.3.3 Test purpose
8.4.2.3.4 Method of test
8.4.2.3.5 Test requirements
8.4.2.4 Correct behaviour when reaching maximum transmit power
8.4.2.4.1 Definition and applicability
8.4.2.4.2 Minimum Requirements
8.4.2.4.3 Test purpose
8.4.2.4.4 Method of test
8.4.2.4.5 Test requirements
8.4.3 Transport format combination selection in UE
8.4.3.1 Interactive or Background, PS, UL: 64 kbps
8.4.3.1.1 Definition and applicability
8.4.3.1.2 Minimum requirements
8.4.3.1.3 Test purpose
8.4.3.1.4 Method of test
8.4.3.1.5 Test requirements
8.4.3.1A Interactive or Background, PS, UL: 64 kbps + Conversational / speech, CS, UL: 12.2kbps
8.4.3.1A.1 Definition and applicability
8.4.3.1A.2 Minimum requirements
8.4.3.1A.3 Test purpose
8.4.3.1A.4 Method of test
8.4.3.1A.5 Test requirements
8.4.4 E-TFC restriction in UE
8.4.4.1 10ms TTI E-DCH E-TFC restriction
8.4.4.1.1 Definition and applicability
8.4.4.1.2 Minimum requirements
8.4.4.1.3 Test Purpose
8.4.4.1.4 Method of test
8.4.4.1.5 Test Requirements
8.4.4.2 2ms TTI E-DCH E-TFC restriction
8.4.4.2.1 Definition and applicability
8.4.4.2.2 Minimum requirements
8.4.4.2.3 Test Purpose
8.4.4.2.4 Method of test
8.4.4.2.5 Test Requirements
8.5 Timing and Signalling Characteristics
8.5.1 UE Transmit Timing
8.5.1.1 Definition and applicability
8.5.1.2 Minimum requirements
8.5.1.3 Test purpose
8.5.1.4 Method of test
8.5.1.5 Test requirements
8.6 UE Measurements Procedures
8.6.1 FDD intra frequency measurements
8.6.1.1 Event triggered reporting in AWGN propagation conditions (R99)
8.6.1.1.1 Definition and applicability
8.6.1.1.2 Minimum requirements
8.6.1.1.3 Test purpose
8.6.1.1.4 Method of test
8.6.1.1.5 Test requirements
8.6.1.1A Event triggered reporting in AWGN propagation conditions (Rel-4 and later)
8.6.1.1A.1 Definition and applicability
8.6.1.1A.2 Minimum requirements
8.6.1.1A.3 Test purpose
8.6.1.1A.4 Method of test
8.6.1.1A.5 Test requirements
8.6.1.2 Event triggered reporting of multiple neighbours in AWGN propagation condition (R99)
8.6.1.2.1 Definition and applicability
8.6.1.2.2 Minimum requirements
8.6.1.2.3 Test purpose
8.6.1.2.4 Method of test
8.6.1.2.5 Test requirements
8.6.1.2A Event triggered reporting of multiple neighbours in AWGN propagation condition (Rel-4 and later)
8.6.1.2A.1 Definition and applicability
8.6.1.2A.2 Minimum requirements
8.6.1.2A.3 Test purpose
8.6.1.2A.4 Method of test
8.6.1.2A.5 Test requirements
8.6.1.3 Event triggered reporting of two detectable neighbours in AWGN propagation condition (R99)
8.6.1.3.1 Definition and applicability
8.6.1.3.2 Minimum requirements
8.6.1.3.3 Test purpose
8.6.1.3.4 Method of test
8.6.1.3.5 Test requirements
8.6.1.3A Event triggered reporting of two detectable neighbours in AWGN propagation condition (Rel-4 and later)
8.6.1.3A.1 Definition and applicability
8.6.1.3A.2 Minimum requirements
8.6.1.3A.3 Test purpose
8.6.1.3A.4 Method of test
8.6.1.3A.5 Test requirements
8.6.1.4 Void
8.6.1.4A Correct reporting of neighbours in fading propagation condition (Rel-4 and later)
8.6.1.4A.1 Definition and applicability
8.6.1.4A.2 Minimum requirements
8.6.1.4A.3 Test purpose
8.6.1.4A.4 Method of test
8.6.1.4A.5 Test requirements
8.6.1.5 Event triggered reporting of multiple neighbour cells in Case 1 fading condition
8.6.1.5.1 Definition and applicability
8.6.1.5.2 Minimum requirements
8.6.1.5.3 Test purpose
8.6.1.5.4 Method of test
8.6.1.5.5 Test requirements
8.6.1.6 Event triggered reporting of multiple neighbour cells in Case 3 fading condition
8.6.1.6.1 Definition and applicability
8.6.1.6.2 Minimum requirements
8.6.1.6.3 Test purpose
8.6.1.6.4 Method of test
8.6.1.6.5 Test requirements
8.6.2 FDD inter frequency measurements
8.6.2.1 Correct reporting of neighbours in AWGN propagation condition (Release 5 and earlier)
8.6.2.1.1 Definition and applicability
8.6.2.1.2 Minimum requirements
8.6.2.1.3 Test purpose
8.6.2.1.4 Method of test
8.6.2.1.5 Test requirements
8.6.2.1A Correct reporting of neighbours in AWGN propagation condition (Release 6 and later)
8.6.2.1A.1 Definition and applicability
8.6.2.1A.2 Minimum requirements
8.6.2.1A.3 Test purpose
8.6.2.1A.4 Method of test
8.6.2.1A.5 Test requirements
8.6.2.2 Correct reporting of neighbours in fading propagation condition (Release 5 only)
8.6.2.2.1 Definition and applicability
8.6.2.2.2 Minimum requirements
8.6.2.2.3 Test purpose
8.6.2.2.4 Method of test
8.6.2.2.4.1 Initial conditions
8.6.2.2.4.2 Procedure
8.6.2.2.5 Test requirements
8.6.2.2A Correct reporting of neighbours in fading propagation condition (Release 6 and later)
8.6.2.2A.1 Definition and applicability
8.6.2.2A.2 Minimum requirements
8.6.2.2A.3 Test purpose
8.6.2.2A.4 Method of test
8.6.2.2A.4.1 Initial conditions
8.6.2.2A.4.2 Procedure
8.6.2.2A.5 Test requirements
8.6.2.3 Correct reporting of neighbours in fading propagation condition using TGL1=14
8.6.2.3.1 Definition and applicability
8.6.2.3.2 Minimum requirements
8.6.2.3.3 Test purpose
8.6.2.3.4 Method of test
8.6.2.3.4.1 Initial conditions
8.6.2.3.4.2 Procedure
8.6.2.3.5 Test requirements
8.6.3 TDD measurements
8.6.3.1 Correct reporting of TDD neighbours in AWGN propagation condition
8.6.3.1.1 Definition and applicability
8.6.3.1.2 Minimum requirement
8.6.3.1.2.1 3.84Mcps TDD option
8.6.3.1.2.2 1.28Mcps TDD option
8.6.3.1.3 Test purpose
8.6.3.1.4 Method of test
8.6.3.1.4.1 Initial conditions
8.6.3.1.4.1.1 3.84Mcps TDD option
8.6.3.1.4.1.2 1.28Mcps TDD option
8.6.3.1.5 Test requirements
8.6.4 GSM measurements
8.6.4.1 Correct reporting of GSM neighbours in AWGN propagation condition
8.6.4.1.1 Definition and applicability
8.6.4.1.2 Minimum requirements
8.6.4.1.3 Test purpose
8.6.4.1.4 Method of test
8.6.4.1.4.1 Test 1 initial conditions
8.6.4.1.4.2 Test 1 Procedure
8.6.4.1.4.3 Test 2 initial conditions
8.6.4.1.4.4 Test 2 Procedure
8.6.4.1.5 Test requirements
8.6.4.1.5.1 TEST 1 With BSIC verification required
8.6.4.1.5.2 TEST 2 Without BSIC verification required
8.6.5 Combined inter frequency and GSM measurements
8.6.5.1 Correct reporting of neighbours in AWGN propagation condition
8.6.5.1.1 Definition and applicability
8.6.5.1.2 Minimum requirement
8.6.5.1.3 Test purpose
8.6.5.1.4 Method of test
8.6.5.1.5 Test requirements
8.6.6 E-UTRAN Measurement
8.6.6.1 Correct reporting of E-UTRAN FDD neighbour in fading propagation condition in CELL_DCH
8.6.6.1.1 Definition and applicability
8.6.6.1.2 Minimum requirement
8.6.6.1.3 Test purpose
8.6.6.1.4 Method of test
8.6.6.1.5 Test requirements
8.6.6.2 Correct reporting of E-UTRAN TDD neighbour in fading propagation condition in CELL_DCH
8.6.6.2.1 Definition and applicability
8.6.6.2.2 Minimum requirement
8.6.6.2.3 Test purpose
8.6.6.2.4 Method of test
8.6.6.2.5 Test requirements
8.6.7 Combined Inter-frequency and E-UTRAN measurements
8.6.7.1 Correct reporting of E-UTRA FDD neighbours in fading propagation condition
8.6.7.1.1 Definition and applicability
8.6.7.1.2 Minimum requirement
8.6.7.1.3 Test purpose
8.6.7.1.4 Method of test
8.6.7.1.5 Test requirements
8.6.7.2 Correct reporting of E-UTRA TDD neighbours in Fading propagation condition
8.6.7.2.1 Definition and applicability
8.6.7.2.2 Minimum requirement
8.6.7.2.3 Test purpose
8.6.7.2.4 Method of test
8.6.7.2.5 Test requirements
8.7 Measurements Performance Requirements
8.7.1 CPICH RSCP
8.7.1.1 Intra frequency measurements accuracy
8.7.1.1.1 Absolute accuracy requirement
8.7.1.1.2 Relative accuracy requirement
8.7.1.2 Inter frequency measurement accuracy
8.7.1.2.1 Relative accuracy requirement
8.7.2 CPICH Ec/Io
8.7.2.1 Intra frequency measurements accuracy
8.7.2.1.1 Absolute accuracy requirement
8.7.2.1.2 Relative accuracy requirement
8.7.2.2 Inter frequency measurement accuracy
8.7.2.2.1 Absolute accuracy requirement
8.7.2.2.2 Relative accuracy requirement
8.7.3 UTRA Carrier RSSI
8.7.3.1 Absolute measurement accuracy requirement
8.7.3.1.1 Definition and applicability
8.7.3.1.2 Minimum Requirements
8.7.3.1.3 Test purpose
8.7.3.1.4 Method of test
8.7.3.1.5 Test requirements
8.7.3.2 Relative measurement accuracy requirement
8.7.3.2.1 Definition and applicability
8.7.3.2.2 Minimum Requirements
8.7.3.2.3 Test purpose
8.7.3.2.4 Method of test
8.7.3.2.5 Test requirements
8.7.3A GSM Carrier RSSI
8.7.3A.1 Definition and applicability
8.7.3A.2 Minimum Requirements
8.7.3A.3 Test purpose
8.7.3A.4 Method of test
8.7.3A.4.1 Initial conditions
8.7.3A.4.2 Procedure
8.7.3A.5 Test requirements
8.7.3B Transport channel BLER
8.7.3C UE transmitted power (R99 and Rel-4 only)
8.7.3C.1 Definition and applicability
8.7.3C.2 Minimum requirements
8.7.3C.3 Test purpose
8.7.3C.4 Method of test
8.7.3C.4.1 Initial conditions
8.7.3C.4.2 Procedure
8.7.3C.5 Test requirements
8.7.3D UE transmitted power (Rel-5 and later)
8.7.3D.1 Definition and applicability
8.7.3D.2 Minimum requirements
8.7.3D.3 Test purpose
8.7.3D.4 Method of test
8.7.3D.4.1 Initial conditions
8.7.3D.4.2 Procedure
8.7.3D.5 Test requirements
8.7.4 SFN-CFN observed time difference
8.7.4.1 Intra frequency measurement requirement
8.7.4.1.1 Definition and applicability
8.7.4.1.2 Minimum requirements
8.7.4.1.3 Test Purpose
8.7.4.1.4 Method of test
8.7.4.1.5 Test requirements
8.7.4.2 Inter frequency measurement requirement
8.7.4.2.1 Definition and applicability
8.7.4.2.2 Minimum requirements
8.7.4.2.3 Test purpose
8.7.4.2.4 Method of test
8.7.4.2.5 Test requirements
8.7.5 SFN-SFN observed time difference
8.7.5.1 SFN-SFN observed time difference type 1
8.7.5.1.1 Definition and applicability
8.7.5.1.2 Minimum requirements
8.7.5.1.3 Test purpose
8.7.5.1.4 Method of test
8.7.5.1.5 Test requirements
8.7.5.2 SFN-SFN observed time difference type 2 without IPDL period active
8.7.5.2.1 Definition and applicability
8.7.5.2.2 Minimum requirements
8.7.5.2.3 Test purpose and Environment
8.7.5.3 SFN-SFN observed time difference type 2 with IPDL period active
8.7.5.3.1 Definition and applicability
8.7.5.3.2 Minimum requirements
8.7.5.3.3 Test purpose and Environment
8.7.6 UE Rx-Tx time difference
8.7.6.1 UE Rx-Tx time difference type 1 (Release 5 and earlier)
8.7.6.1.1 Definition and applicability
8.7.6.1.2 Minimum requirements
8.7.6.1.3 Test purpose
8.7.6.1.4 Method of test
8.7.6.1.5 Test requirements
8.7.6.1A UE Rx-Tx time difference type 1 (Release 6 and later)
8.7.6.1A.1 Definition and applicability
8.7.6.1A.2 Minimum requirements
8.7.6.1A.3 Test purpose
8.7.6.1A.4 Method of test
8.7.6.1A.5 Test requirements
8.7.6.2 UE Rx-Tx time difference type 2
8.7.6.2.1 Definition and applicability
8.7.6.2.2 Minimum requirements
8.7.6.2.3 Test purpose
8.7.7 Observed time difference to GSM cell (R99 and Rel-4 only)
8.7.8 P-CCPCH RSCP
8.7.8.1 Absolute measurement accuracy
8.7.8.1.1 Definition and applicability
8.7.8.1.2 Minimum Requirements
8.7.8.1.3 Test purpose
8.7.8.1.4 Method of test
8.7.8.1.5 Test requirements
8.7.9 UE Transmission Power Headroom
8.7.9.1 Definition and applicability
8.7.9.2 Minimum Requirements
8.7.9.3 Test purpose
8.7.9.4 Method of test
8.7.9.4.1 Initial conditions
8.7.9.4.2 Test procedure
8.7.9.5 Test requirements
8.7.10 E-UTRAN FDD RSRP absolute accuracy (CELL_DCH)
8.7.10.1 Definition and applicability
8.7.10.2 Minimum Requirements
8.7.10.3 Test purpose
8.7.10.4 Method of test
8.7.10.5 Test requirements
8.7.11 E-UTRAN TDD RSRP absolute accuracy (CELL_DCH)
8.7.11.1 Definition and applicability
8.7.11.2 Minimum Requirements
8.7.11.3 Test purpose
8.7.11.4 Method of test
8.7.11.5 Test requirements
8.7.12 E-UTRAN FDD RSRQ absolute accuracy (CELL_DCH)
8.7.12.1 Definition and applicability
8.7.12.2 Minimum Requirements
8.7.12.3 Test purpose
8.7.12.4 Method of test
8.7.12.5 Test requirements
8.7.13 E-UTRAN TDD RSRQ absolute accuracy (CELL_DCH)
8.7.13.1 Definition and applicability
8.7.13.2 Minimum Requirements
8.7.13.3 Test purpose
8.7.13.4 Method of test
8.7.13.5 Test requirements
9 Performance requirements for HSDPA
9.1 General
9.2 Demodulation of HS-DSCH (Fixed Reference Channel)
9.2.1 Single Link Performance
9.2.1A Single Link Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2/3
9.2.1A.1 Definition and applicability
9.2.1A.2 Minimum requirements
9.2.1A.3 Test purpose
9.2.1A.4 Method of test
9.2.1A.4.1 Initial conditions
9.2.1A.4.2 Procedure
9.2.1A.5 Test Requirements
9.2.1B Single Link Performance - QPSK, Fixed Reference Channel (FRC) H-Set 4/5
9.2.1B.1 Definition and applicability
9.2.1B.2 Minimum requirements
9.2.1B.3 Test purpose
9.2.1B.4 Method of test
9.2.1B.4.1 Initial conditions
9.2.1B.4.2 Procedure
9.2.1B.5 Test Requirements
9.2.1C Single Link Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6/3
9.2.1C.1 Definition and applicability
9.2.1C.2 Minimum requirements
9.2.1C.3 Test purpose
9.2.1C.4 Method of test
9.2.1C.4.1 Initial conditions
9.2.1C.4.2 Procedure
9.2.1C.5 Test Requirements
9.2.1D Single Link Performance - Enhanced Performance Requirements Type 1 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2
9.2.1D.1 Definition and applicability
9.2.1D.2 Minimum requirements
9.2.1D.3 Test purpose
9.2.1D.4 Method of test
9.2.1D.4.1 Initial conditions
9.2.1D.4.2 Procedure
9.2.1D.5 Test Requirements
9.2.1E Single Link Performance - Enhanced Performance Requirements Type 1- QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6/3
9.2.1E.1 Definition and applicability
9.2.1E.2 Minimum requirements
9.2.1E.3 Test purpose
9.2.1E.4 Method of test
9.2.1E.4.1 Initial conditions
9.2.1E.4.2 Procedure
9.2.1E.5 Test Requirements
9.2.1F Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6/3
9.2.1F.1 Definition and applicability
9.2.1F.2 Minimum requirements
9.2.1F.3 Test purpose
9.2.1F.4 Method of test
9.2.1F.4.1 Initial conditions
9.2.1F.4.2 Procedure
9.2.1F.5 Test Requirements
9.2.1FA Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6A
9.2.1FA.1 Definition and applicability
9.2.1FA.2 Minimum requirements
9.2.1FA.3 Test purpose
9.2.1FA.4 Method of test
9.2.1FA.4.1 Initial conditions
9.2.1FA.4.2 Procedure
9.2.1FA.5 Test Requirements
9.2.1FB Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6A
9.2.1FB.1 Definition and applicability
9.2.1FB.2 Minimum requirements
9.2.1FB.3 Test purpose
9.2.1FB.4 Method of test
9.2.1FB.4.1 Initial conditions
9.2.1FB.4.2 Procedure
9.2.1FB.5 Test Requirements
9.2.1FC Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6B
9.2.1FC.1 Definition and applicability
9.2.1FC.2 Minimum requirements
9.2.1FC.3 Test purpose
9.2.1FC.4 Method of test
9.2.1FC.4.1 Initial conditions
9.2.1FC.4.2 Procedure
9.2.1FC.5 Test Requirements
9.2.1FD Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6C
9.2.1FD.1 Definition and applicability
9.2.1FD.2 Minimum requirements
9.2.1FD.3 Test purpose
9.2.1FD.4 Method of test
9.2.1FD.4.1 Initial conditions
9.2.1FD.4.2 Procedure
9.2.1FD.5 Test Requirements
9.2.1G Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6/3
9.2.1G.1 Definition and applicability
9.2.1G.2 Minimum requirements
9.2.1G.3 Test purpose
9.2.1G.4 Method of test
9.2.1G.4.1 Initial conditions
9.2.1G.4.2 Procedure
9.2.1G.5 Test Requirements
9.2.1GA Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6A
9.2.1GA.1 Definition and applicability
9.2.1GA.2 Minimum requirements
9.2.1GA.3 Test purpose
9.2.1GA.4 Method of test
9.2.1GA.4.1 Initial conditions
9.2.1GA.4.2 Procedure
9.2.1GA.5 Test Requirements
9.2.1GB Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6A
9.2.1GB.1 Definition and applicability
9.2.1GB.2 Minimum requirements
9.2.1GB.3 Test purpose
9.2.1GB.4 Method of test
9.2.1GB.4.1 Initial conditions
9.2.1GB.4.2 Procedure
9.2.1GB.5 Test Requirements
9.2.1GC Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6B
9.2.1GC.1 Definition and applicability
9.2.1GC.2 Minimum requirements
9.2.1GC.3 Test purpose
9.2.1GC.4 Method of test
9.2.1GC.4.1 Initial conditions
9.2.1GC.4.2 Procedure
9.2.1GC.5 Test Requirements
9.2.1GD Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 6C
9.2.1GD.1 Definition and applicability
9.2.1GD.2 Minimum requirements
9.2.1GD.3 Test purpose
9.2.1GD.4 Method of test
9.2.1GD.4.1 Initial conditions
9.2.1GD.4.2 Procedure
9.2.1GD.5 Test Requirements
9.2.1H Single Link Performance - Enhanced Performance Requirements Type 2 - 64QAM, Fixed Reference Channel (FRC) H-Set 8
9.2.1H.1 Definition and applicability
9.2.1H.2 Minimum requirements
9.2.1H.3 Test purpose
9.2.1H.4 Method of test
9.2.1H.4.1 Initial conditions
9.2.1H.4.2 Procedure
9.2.1H.5 Test Requirements
9.2.1HA Single Link Performance - Enhanced Performance Requirements Type 2 - 64QAM, Fixed Reference Channel (FRC) H-Set 8 A
9.2.1HA.1 Definition and applicability
9.2.1HA.2 Minimum requirements
9.2.1HA.3 Test purpose
9.2.1HA.4 Method of test
9.2.1HA.4.1 Initial conditions
9.2.1HA.4.2 Procedure
9.2.1HA.5 Test Requirements
9.2.1HB Single Link Performance - Enhanced Performance Requirements Type 2 - 64QAM, Fixed Reference Channel (FRC) H-Set 8 A for
9.2.1HB.1 Definition and applicability
9.2.1HB.2 Minimum requirements
9.2.1HB.3 Test purpose
9.2.1HB.4 Method of test
9.2.1HB.4.1 Initial conditions
9.2.1HB.4.2 Procedure
9.2.1HB.5 Test Requirements
9.2.1HC Single Link Performance - Enhanced Performance Requirements Type 2 - 64QAM, Fixed Reference Channel (FRC) H-Set 8B
9.2.1HC.1 Definition and applicability
9.2.1HC.2 Minimum requirements
9.2.1HC.3 Test purpose
9.2.1HC.4 Method of test
9.2.1HC.4.1 Initial conditions
9.2.1HC.4.2 Procedure
9.2.1HC.5 Test Requirements
9.2.1HD Single Link Performance - Enhanced Performance Requirements Type 2 - 64QAM, Fixed Reference Channel (FRC) H-Set 8C
9.2.1HD.1 Definition and applicability
9.2.1HD.2 Minimum requirements
9.2.1HD.3 Test purpose
9.2.1HD.4 Method of test
9.2.1HD.4.1 Initial conditions
9.2.1HD.4.2 Procedure
9.2.1HD.5 Test Requirements
9.2.1I Single Link Performance - Enhanced Performance Requirements Type 3 - 64QAM, Fixed Reference Channel (FRC) H-Set 8
9.2.1I.1 Definition and applicability
9.2.1I.2 Minimum requirements
9.2.1I.3 Test purpose
9.2.1I.4 Method of test
9.2.1I.4.1 Initial conditions
9.2.1I.4.2 Procedure
9.2.1I.5 Test Requirements
9.2.1IA Single Link Performance - Enhanced Performance Requirements Type 3 - 64QAM, Fixed Reference Channel (FRC) H-Set 8A
9.2.1IA.1 Definition and applicability
9.2.1IA.2 Minimum requirements
9.2.1IA.3 Test purpose
9.2.1IA.4 Method of test
9.2.1IA.4.1 Initial conditions
9.2.1IA.4.2 Procedure
9.2.1IA.5 Test Requirements
9.2.1IB Single Link Performance - Enhanced Performance Requirements Type 3 - 64QAM, Fixed Reference Channel (FRC) H-Set 8A for
9.2.1IB.1 Definition and applicability
9.2.1IB.2 Minimum requirements
9.2.1IB.3 Test purpose
9.2.1IB.4 Method of test
9.2.1IB.4.1 Initial conditions
9.2.1IB.4.2 Procedure
9.2.1IB.5 Test Requirements
9.2.1IC Single Link Performance - Enhanced Performance Requirements Type 3 - 64QAM, Fixed Reference Channel (FRC) H-Set 8B
9.2.1IC.1 Definition and applicability
9.2.1IC.2 Minimum requirements
9.2.1IC.3 Test purpose
9.2.1IC.4 Method of test
9.2.1IC.4.1 Initial conditions
9.2.1IC.4.2 Procedure
9.2.1IC.5 Test Requirements
9.2.1ID Single Link Performance - Enhanced Performance Requirements Type 3 - 64QAM, Fixed Reference Channel (FRC) H-Set 8C
9.2.1ID.1 Definition and applicability
9.2.1ID.2 Minimum requirements
9.2.1ID.3 Test purpose
9.2.1ID.4 Method of test
9.2.1ID.4.1 Initial conditions
9.2.1ID.4.2 Procedure
9.2.1ID.5 Test Requirements
9.2.1J Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1J.1 Definition and applicability
9.2.1J.2 Minimum requirements
9.2.1J.3 Test purpose
9.2.1J.4 Method of test
9.2.1J.4.1 Initial conditions
9.2.1J.4.2 Procedure
9.2.1J.5 Test Requirements
9.2.1JA Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1JA.1 Definition and applicability
9.2.1JA.2 Minimum requirements
9.2.1JA.3 Test purpose
9.2.1JA.4 Method of test
9.2.1JA.4.1 Initial conditions
9.2.1JA.4.2 Procedure
9.2.1JA.5 Test Requirements
9.2.1JB Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1JB.1 Definition and applicability
9.2.1JB.2 Minimum requirements
9.2.1JB.3 Test purpose
9.2.1JB.4 Method of test
9.2.1JB.4.1 Initial conditions
9.2.1JB.4.2 Procedure
9.2.1JB.5 Test Requirements
9.2.1JC Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1JC.1 Definition and applicability
9.2.1JC.2 Minimum requirements
9.2.1JC.3 Test purpose
9.2.1JC.4 Method of test
9.2.1JC.4.1 Initial conditions
9.2.1JC.4.2 Procedure
9.2.1JC.5 Test Requirements
9.2.1JD Single Link Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1JD.1 Definition and applicability
9.2.1JD.2 Minimum requirements
9.2.1JD.3 Test purpose
9.2.1JD.4 Method of test
9.2.1JD.4.1 Initial conditions
9.2.1JD.4.2 Procedure
9.2.1JD.5 Test Requirements
9.2.1K Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1K.1 Definition and applicability
9.2.1K.2 Minimum requirements
9.2.1K.3 Test purpose
9.2.1K.4 Method of test
9.2.1K.4.1 Initial conditions
9.2.1K.4.2 Procedure
9.2.1K.5 Test Requirements
9.2.1KA Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1KA.1 Definition and applicability
9.2.1KA.2 Minimum requirements
9.2.1KA.3 Test purpose
9.2.1KA.4 Method of test
9.2.1KA.4.1 Initial conditions
9.2.1KA.4.2 Procedure
9.2.1KA.5 Test Requirements
9.2.1KB Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1KB.1 Definition and applicability
9.2.1KB.2 Minimum requirements
9.2.1KB.3 Test purpose
9.2.1KB.4 Method of test
9.2.1KB.4.1 Initial conditions
9.2.1KB.4.2 Procedure
9.2.1KB.5 Test Requirements
9.2.1KC Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1KC.1 Definition and applicability
9.2.1KC.2 Minimum requirements
9.2.1KC.3 Test purpose
9.2.1KC.4 Method of test
9.2.1KC.4.1 Initial conditions
9.2.1KC.4.2 Procedure
9.2.1KC.5 Test Requirements
9.2.1KD Single Link Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 10
9.2.1KD.1 Definition and applicability
9.2.1KD.2 Minimum requirements
9.2.1KD.3 Test purpose
9.2.1KD.4 Method of test
9.2.1KD.4.1 Initial conditions
9.2.1KD.4.2 Procedure
9.2.1KD.5 Test Requirements
9.2.1L Single Link Performance - Enhanced Performance Requirements Type 3i - QPSK, Fixed Reference Channel (FRC) H-Set 6
9.2.1L.1 Definition and applicability
9.2.1L.2 Minimum requirements
9.2.1L.3 Test purpose
9.2.1L.4 Method of test
9.2.1L.5 Test Requirements
9.2.1LA Enhanced Performance Requirements Type 3i - QPSK, Fixed Reference Channel (FRC) H-Set 6A
9.2.1LA.1 Definition and applicability
9.2.1LA.2 Minimum requirements
9.2.1LA.3 Test purpose
9.2.1LA.4 Method of test
9.2.1LA.5 Test Requirements
9.2.1LB Enhanced Performance Requirements Type 3i - QPSK, Fixed Reference Channel (FRC) H-Set 6A for DB-DC-HSDPA
9.2.1LB.1 Definition and applicability
9.2.1LB.2 Minimum requirements
9.2.1LB.3 Test purpose
9.2.1LB.4 Method of test
9.2.1LB.5 Test Requirements
9.2.1LC Enhanced Performance Requirements Type 3i - QPSK, Fixed Reference Channel (FRC) H-Set 6B
9.2.1LC.1 Definition and applicability
9.2.1LC.2 Minimum requirements
9.2.1LC.3 Test purpose
9.2.1LC.4 Method of test
9.2.1LC.5 Test Requirements
9.2.1LD Enhanced Performance Requirements Type 3i - QPSK, Fixed Reference Channel (FRC) H-Set 6C
9.2.1LD.1 Definition and applicability
9.2.1LD.2 Minimum requirements
9.2.1LD.3 Test purpose
9.2.1LD.4 Method of test
9.2.1LD.5 Test Requirements
9.2.1M Single Link Performance - Enhanced Performance Requirements Type 3i Π16QAM/QPSK, Fixed Reference Channel (FRC) H-Set 6
9.2.1M.1 Definition and applicability
9.2.1M.2 Minimum requirements
9.2.1M.3 Test purpose
9.2.1M.4 Method of test
9.2.1M.4.1 Initial conditions
9.2.1M.4.2 Procedure
9.2.1M.5 Test Requirements
9.2.1MA Single Link Performance - Enhanced Performance Requirements Type 3i Π16QAM/QPSK, Fixed Reference Channel (FRC) H-Set 6
9.2.1MA.1 Definition and applicability
9.2.1MA.2 Minimum requirements
9.2.1MA.3 Test purpose
9.2.1MA.4 Method of test
9.2.1MA.4.1 Initial conditions
9.2.1MA.4.2 Procedure
9.2.1MA.5 Test Requirements
9.2.2 Open Loop Diversity Performance
9.2.2A Open Loop Diversity Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2/3
9.2.2A.1 Definition and applicability
9.2.2A.2 Minimum requirements
9.2.2A.3 Test purpose
9.2.2A.4 Method of test
9.2.2B Open Loop Diversity Performance - QPSK, Fixed Reference Channel (FRC) H-Set 4/5
9.2.2B.1 Definition and applicability
9.2.2B.2 Minimum requirements
9.2.2B.3 Test purpose
9.2.2B.4 Method of test
9.2.2C Open Loop Diversity Performance - Enhanced Performance Requirements Type 1 - QPSK/16QAM, Fixed Reference Channel (FRC) H
9.2.2C.1 Definition and applicability
9.2.2C.2 Minimum requirements
9.2.2C.3 Test purpose
9.2.2C.4 Method of test
9.2.2D Open Loop Diversity Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC) H
9.2.2D.1 Definition and applicability
9.2.2D.2 Minimum requirements
9.2.2D.3 Test purpose
9.2.2D.4 Method of test
9.2.2D.4.1 Initial conditions
9.2.2D.4.2 Procedure
9.2.2D.5 Test Requirements
9.2.2E Open Loop Diversity Performance - Enhanced Performance Requirements Type 3 - QPSK/16QAM, Fixed Reference Channel (FRC) H
9.2.2E.1 Definition and applicability
9.2.2E.2 Minimum requirements
9.2.2E.3 Test purpose
9.2.2E.4 Method of test
9.2.2E.4.1 Initial conditions
9.2.2E.4.2 Procedure
9.2.2E.5 Test Requirements
9.2.3 Closed Loop Diversity Performance
9.2.3A Closed Loop Diversity Performance - QPSK/16QAM, Fixed Reference Channel (FRC) H-Set 1/2/3
9.2.3A.1 Definition and applicability
9.2.3A.2 Minimum requirements
9.2.3A.3 Test purpose
9.2.3A.4 Method of test
9.2.3A.4.1 Initial conditions
9.2.3A.4.2 Procedure
9.2.3A.5 Test Requirements
9.2.3B Closed Loop Diversity Performance - QPSK, Fixed Reference Channel (FRC) H-Set 4/5
9.2.3B.1 Definition and applicability
9.2.3B.2 Minimum requirements
9.2.3B.3 Test purpose
9.2.3B.4 Method of test
9.2.3B.4.1 Initial conditions
9.2.3B.4.2 Procedure
9.2.3B.5 Test Requirements
9.2.3C Closed Loop Diversity Performance Enhanced Performance Requirements Type 1, QPSK/16QAM, Fixed Reference Channel (FRC) H-
9.2.3C.1 Definition and applicability
9.2.3C.2 Minimum requirements
9.2.3C.3 Test purpose
9.2.3C.4 Method of test
9.2.3C.4.1 Initial conditions
9.2.3C.4.2 Procedure
9.2.3C.5 Test Requirements
9.2.3D Closed Loop Diversity Performance - Enhanced Performance Requirements Type 2 - QPSK/16QAM, Fixed Reference Channel (FRC)
9.2.3D.1 Definition and applicability
9.2.3D.2 Minimum requirements
9.2.3D.3 Test purpose
9.2.3D.4 Method of test
9.2.3D.4.1 Initial conditions
9.2.3D.4.2 Procedure
9.2.3D.5 Test Requirements
9.2.3E Closed Loop Diversity Performance Enhanced Performance Requirements Type 3, QPSK/16QAM, Fixed Reference Channel (FRC) H-
9.2.3E.1 Definition and applicability
9.2.3E.2 Minimum requirements
9.2.3E.3 Test purpose
9.2.3E.4 Method of test
9.2.3E.4.1 Initial conditions
9.2.3E.4.2 Procedure
9.2.3E.5 Test Requirements
9.2.4 MIMO Performance
9.2.4A MIMO Performance - Fixed Reference Channel (FRC) H-Set 9
9.2.4A.1 Definition and applicability
9.2.4A.2 Minimum requirements
9.2.4A.3 Test purpose
9.2.4A.4 Method of test
9.2.4A.4.1 Initial conditions
9.2.4A.4.2 Procedure
9.2.4A.5 Test Requirements
9.2.4B MIMO Performance - Fixed Reference Channel (FRC) H-Set 11
9.2.4B.1 Definition and applicability
9.2.4B.2 Minimum requirements
9.2.4B.3 Test purpose
9.2.4B.4 Method of test
9.2.4B.4.1 Initial conditions
9.2.4B.4.2 Procedure
9.2.4B.5 Test Requirements
9.2.4C MIMO Performance - Fixed Reference Channel (FRC) H-Set 9A
9.2.4C.1 Definition and applicability
9.2.4C.2 Minimum requirements
9.2.4C.3 Test purpose
9.2.4C.4 Method of test
9.2.4C.4.1 Initial conditions
9.2.4C.4.2 Procedure
9.2.4C.5 Test Requirements
9.2.4CA MIMO Performance - Fixed Reference Channel (FRC) H-Set 9A for DB DC-HSDPA
9.2.4CA.1 Definition and applicability
9.2.4CA.2 Minimum requirements
9.2.4CA.3 Test purpose
9.2.4CA.4 Method of test
9.2.4CA.4.1 Initial conditions
9.2.4CA.4.2 Procedure
9.2.4CA.5 Test Requirements
9.2.4D MIMO Performance - Fixed Reference Channel (FRC) H-Set 11A
9.2.4D.1 Definition and applicability
9.2.4D.2 Minimum requirements
9.2.4D.3 Test purpose
9.2.4D.4 Method of test
9.2.4D.4.1 Initial conditions
9.2.4D.4.2 Procedure
9.2.4D.5 Test Requirements
9.2.4DA MIMO Performance - Fixed Reference Channel (FRC) H-Set 11A for DB DC-HSDPA
9.2.4DA.1 Definition and applicability
9.2.4DA.2 Minimum requirements
9.2.4DA.3 Test purpose
9.2.4DA.4 Method of test
9.2.4DA.4.1 Initial conditions
9.2.4DA.4.2 Procedure
9.2.4DA.5 Test Requirements
9.2.4E MIMO Performance - Fixed Reference Channel (FRC) H-Set 9 Asymmetric CPICHs
9.2.4E.1 Definition and applicability
9.2.4E.2 Minimum requirements
9.2.4E.3 Test purpose
9.2.4E.4 Method of test
9.2.4E.4.1 Initial conditions
9.2.4E.4.2 Procedure
9.2.4E.5 Test Requirements
9.2.4F MIMO Performance - Fixed Reference Channel (FRC) H-Set 11 Asymmetric CPICHs
9.2.4F.1 Definition and applicability
9.2.4F.2 Minimum requirements
9.2.4F.3 Test purpose
9.2.4F.4 Method of test
9.2.4F.4.1 Initial conditions
9.2.4F.4.2 Procedure
9.2.4F.5 Test Requirements
9.2.4G MIMO Performance - Fixed Reference Channel (FRC) H-Set 9A Asymmetric CPICHs
9.2.4G.1 Definition and applicability
9.2.4G.2 Minimum requirements
9.2.4G.3 Test purpose
9.2.4G.4 Method of test
9.2.4G.4.1 Initial conditions
9.2.4G.4.2 Procedure
9.2.4G.5 Test Requirements
9.2.4H MIMO Performance - Fixed Reference Channel (FRC) H-Set 11A Asymmetric CPICHs
9.2.4H.1 Definition and applicability
9.2.4H.2 Minimum requirements
9.2.4H.3 Test purpose
9.2.4H.4 Method of test
9.2.4H.4.1 Initial conditions
9.2.4H.4.2 Procedure
9.2.4H.5 Test Requirements
9.3 Reporting of Channel Quality Indicator
9.3.1 Single Link Performance - AWGN Propagation Conditions
9.3.1.1 Definition and applicability
9.3.1.2 Minimum requirements
9.3.1.3 Test purpose
9.3.1.4 Method of test
9.3.1.4.1 Initial conditions
9.3.1.4.2 Procedure
9.3.1.5 Test Requirements
9.3.1A Single Link Performance - AWGN Propagation Conditions, 64QAM
9.3.1A.1 Definition and applicability
9.3.1A.2 Minimum requirements
9.3.1A.3 Test purpose
9.3.1A.4 Method of test
9.3.1A.4.1 Initial conditions
9.3.1A.4.2 Procedure
9.3.1A.5 Test Requirements
9.3.1B Single Link Performance - AWGN Propagation Conditions, DC-HSDPA requirements
9.3.1B.1 Definition and applicability
9.3.1B.2 Minimum requirements
9.3.1B.3 Test purpose
9.3.1B.4 Method of test
9.3.1B.4.1 Initial conditions
9.3.1B.4.2 Procedure
9.3.1B.5 Test Requirements
9.3.1BA Single Link Performance - AWGN Propagation Conditions, DB-DC-HSDPA requirements
9.3.1BA.1 Definition and applicability
9.3.1BA.2 Minimum requirements
9.3.1BA.4 Method of test
9.3.1BA.4.1 Initial conditions
9.3.1BA.4.2 Procedure
9.3.1BA.5 Test Requirements
9.3.1BB Single Link Performance - AWGN Propagation Conditions, 4C-HSDPA requirements (3 Carriers)
9.3.1BB.1 Definition and applicability
9.3.1BB.2 Minimum requirements
9.3.1BB.4 Method of test
9.3.1BB.4.1 Initial conditions
9.3.1BB.4.2 Procedure
9.3.1BB.5 Test Requirements
9.3.1BC Single Link Performance - AWGN Propagation Conditions, 4C-HSDPA requirements
9.3.1BC.1 Definition and applicability
9.3.1BC.2 Minimum requirements
9.3.1BC.4 Method of test
9.3.1BC.4.1 Initial conditions
9.3.1BC.4.2 Procedure
9.3.1BC.5 Test Requirements
9.3.2AB Single Link Performance - Fading Propagation Conditions, 4C-HSDPA requirements(3 Carriers)
9.3.2AB.1 Definition and applicability
9.3.2AB.2 Minimum requirements
9.3.2AB.3 Test purpose
9.3.2AB.4 Method of test
9.3.2AB.4.1 Initial conditions
9.3.2AB.4.2 Procedure
9.3.2AB.5 Test Requirements
9.3.2AC Single Link Performance - Fading Propagation Conditions, 4C-HSDPA requirements
9.3.2AC.1 Definition and applicability
9.3.2AC.2 Minimum requirements
9.3.2AC.3 Test purpose
9.3.2AC.4 Method of test
9.3.2AC.4.1 Initial conditions
9.3.2AC.4.2 Procedure
9.3.2AC.5 Test Requirements
9.3.1C Single Link Performance - AWGN Propagation Conditions, Periodically Varying Radio Conditions
9.3.1C.1 Definition and applicability
9.3.1C.2 Minimum requirements
9.3.1C.3 Test purpose
9.3.1C.4 Method of test
9.3.1C.4.1 Initial conditions
9.3.1C.4.2 Procedure
9.3.1C.5 Test Requirements
9.3.2 Single Link Performance - Fading Propagation Conditions
9.3.2.1 Definition and applicability
9.3.2.2 Minimum requirements
9.3.2.3 Test purpose
9.3.2.4 Method of test
9.3.2.4.1 Initial conditions
9.3.2.4.2 Procedure
9.3.2.5 Test Requirements
9.3.2A Single Link Performance - Fading Propagation Conditions, DC-HSDPA requirements
9.3.2A.1 Definition and applicability
9.3.2A.2 Minimum requirements
9.3.2A.3 Test purpose
9.3.2A.4 Method of test
9.3.2A.4.1 Initial conditions
9.3.2A.4.2 Procedure
9.3.2A.5 Test Requirements
9.3.2AA Single Link Performance - Fading Propagation Conditions, DB-DC-HSDPA requirements
9.3.2AA.1 Definition and applicability
9.3.2AA.2 Minimum requirements
9.3.2AA.3 Test purpose
9.3.2AA.4 Method of test
9.3.2AA.4.1 Initial conditions
9.3.2AA.4.2 Procedure
9.3.2AA.5 Test Requirements
9.3.2B Single Link Performance - Fading Propagation Conditions, 64QAM
9.3.2B.1 Definition and applicability
9.3.2B.2 Minimum requirements
9.3.2B.3 Test purpose
9.3.2B.4 Method of test
9.3.2B.4.1 Initial conditions
9.3.2B.4.2 Procedure
9.3.2B.5 Test Requirements
9.3.2C Single Link Performance - Fading Propagation Conditions, Multiflow HSDPA requirements (2 Cells)
9.3.2C.1 Definition and applicability
9.3.2C.2 Minimum requirements
9.3.2C.3 Test purpose
9.3.2C.4 Method of test
9.3.2C.4.1 Initial conditions
9.3.2C.4.2 Procedure
9.3.2C.5 Test Requirements
9.3.2CA Single Link Performance - Fading Propagation Conditions, Multiflow HSDPA requirements (3 Cells)
9.3.2CA.1 Definition and applicability
9.3.2CA.2 Minimum requirements
9.3.2CA.3 Test purpose
9.3.2CA.4 Method of test
9.3.2CA.4.1 Initial conditions
9.3.2CA.4.2 Procedure
9.3.2CA.5 Test Requirements
9.3.3 Open Loop Diversity Performance - AWGN Propagation Conditions
9.3.3.1 Definition and applicability
9.3.3.2 Minimum requirements
9.3.3.3 Test purpose
9.3.3.4 Method of test
9.3.3.4.1 Initial conditions
9.3.3.4.2 Procedure
9.3.3.5 Test Requirements
9.3.4 Open Loop Diversity Performance - Fading Propagation Conditions
9.3.4.1 Definition and applicability
9.3.4.2 Minimum requirements
9.3.4.3 Test purpose
9.3.4.4 Method of test
9.3.4.4.1 Initial conditions
9.3.4.4.2 Procedure
9.3.4.5 Test Requirements
9.3.5 Closed Loop Diversity Performance - AWGN Propagation Conditions
9.3.5.1 Definition and applicability
9.3.5.2 Minimum requirements
9.3.5.3 Test purpose
9.3.5.4 Method of test
9.3.5.4.1 Initial conditions
9.3.5.4.2 Procedure
9.3.5.5 Test Requirements
9.3.6 Closed Loop Diversity Performance - Fading Propagation Conditions
9.3.6.1 Definition and applicability
9.3.6.2 Minimum requirements
9.3.6.3 Test purpose
9.3.6.4 Method of test
9.3.6.4.1 Initial conditions
9.3.6.4.2 Procedure
9.3.6.5 Test Requirements
9.3.7 MIMO Performance - Reporting of Channel Quality Indicator
9.3.7A MIMO Single Stream Fading Conditions
9.3.7A.1 Definition and applicability
9.3.7A.2 Minimum requirements
9.3.7A.3 Test purpose
9.3.7A.4 Method of test
9.3.7A.4.1 Initial conditions
9.3.7A.4.2 Procedure
9.3.7A.5 Test Requirements
9.3.7B MIMO Dual Stream Fading Conditions
9.3.7B.1 Definition and applicability
9.3.7B.2 Minimum requirements
9.3.7B.3 Test purpose
9.3.7B.4 Method of test
9.3.7B.4.1 Initial conditions
9.3.7B.4.2 Procedure
9.3.7B.5 Test Requirements
9.3.7C MIMO Dual Stream Fading Conditions - UE categories 19-20
9.3.7C.1 Definition and applicability
9.3.7C.2 Minimum requirements
9.3.7C.3 Test purpose
9.3.7C.4 Method of test
9.3.7C.4.1 Initial conditions
9.3.7C.4.2 Procedure
9.3.7C.5 Test Requirements
9.3.7D MIMO Dual Stream Static Orthogonal Conditions - UE categories 15-20
9.3.7D.1 Definition and applicability
9.3.7D.2 Minimum requirements
9.3.7D.3 Test purpose
9.3.7D.4 Method of test
9.3.7D.4.1 Initial conditions
9.3.7D.4.2 Procedure
9.3.7D.5 Test Requirements
9.3.7E MIMO Dual Stream Static Orthogonal Conditions - UE categories 19-20
9.3.7E.1 Definition and applicability
9.3.7E.2 Minimum requirements
9.3.7E.3 Test purpose
9.3.7E.4 Method of test
9.3.7E.4.1 Initial conditions
9.3.7E.4.2 Procedure
9.3.7E.5 Test Requirements
9.3.7F MIMO Single Stream Fading Conditions - Asymmetric CPICHs
9.3.7F.1 Definition and applicability
9.3.7F.2 Minimum requirements
9.3.7F.3 Test purpose
9.3.7F.4 Method of test
9.3.7F.4.1 Initial conditions
9.3.7F.4.2 Procedure
9.3.7F.5 Test Requirements
9.3.7G MIMO Dual Stream Fading Conditions- Asymmetric CPICHs
9.3.7G.1 Definition and applicability
9.3.7G.2 Minimum requirements
9.3.7G.3 Test purpose
9.3.7G.4 Method of test
9.3.7G.4.1 Initial conditions
9.3.7G.4.2 Procedure
9.3.7G.5 Test Requirements
9.3.7H MIMO Dual Stream Fading Conditions - UE categories 19-20 - Asymmetric CPICHs
9.3.7H.1 Definition and applicability
9.3.7H.2 Minimum requirements
9.3.7H.3 Test purpose
9.3.7H.4 Method of test
9.3.7H.4.1 Initial conditions
9.3.7H.4.2 Procedure
9.3.7H.5 Test Requirements
9.3.7I MIMO Dual Stream Static Orthogonal Conditions - UE categories 15-20 - Asymmetric CPICHs
9.3.7I.1 Definition and applicability
9.3.7I.2 Minimum requirements
9.3.7I.3 Test purpose
9.3.7I.4 Method of test
9.3.7I.4.1 Initial conditions
9.3.7I.4.2 Procedure
9.3.7I.5 Test Requirements
9.3.7J MIMO Dual Stream Static Orthogonal Conditions - UE categories 19-20- Asymmetric CPICHs
9.3.7J.1 Definition and applicability
9.3.7J.2 Minimum requirements
9.3.7J.3 Test purpose
9.3.7J.4 Method of test
9.3.7J.4.1 Initial conditions
9.3.7J.4.2 Procedure
9.3.7J.5 Test Requirements
9.4 HS-SCCH Detection Performance
9.4.1 Single Link Performance
9.4.1.1 Definition and applicability
9.4.1.2 Minimum requirements
9.4.1.3 Test purpose
9.4.1.4 Method of test
9.4.1.4.1 Initial conditions
9.4.1.4.2 Procedure
9.4.1.5 Test Requirements
9.4.1A Single Link Performance - Enhanced Performance Requirements Type 1
9.4.1A.1 Definition and applicability
9.4.1A.2 Minimum requirements
9.4.1A.3 Test purpose
9.4.1A.4 Method of test
9.4.1A.4.1 Initial conditions
9.4.1A.4.2 Procedure
9.4.1A.5 Test Requirements
9.4.2 Open Loop Diversity Performance
9.4.2.1 Definition and applicability
9.4.2.2 Minimum requirements
9.4.2.3 Test purpose
9.4.2.4 Method of test
9.4.2.4.1 Initial conditions
9.4.2.4.2 Procedure
9.4.2.5 Test Requirements
9.4.2A Open Loop Diversity Performance - Enhanced Performance Requirements Type 1
9.4.2A.1 Definition and applicability
9.4.2A.2 Minimum requirements
9.4.2A.3 Test purpose
9.4.2A.4 Method of test
9.4.2A.4.1 Initial conditions
9.4.2A.4.2 Procedure
9.4.2A.5 Test Requirements
9.4.3 HS-SCCH Type 3 Performance
9.4.3.1 Definition and applicability
9.4.3.2 Minimum requirements
9.4.3.3 Test purpose
9.4.3.4 Method of test
9.4.3.4.1 Initial conditions
9.4.3.4.2 Procedure
9.4.3.5 Test Requirements
9.4.3A HS-SCCH Type 3 Performance -STTD disabled- Asymmetric CPICHs
9.4.3A.1 Definition and applicability
9.4.3A.2 Minimum requirements
9.4.3A.3 Test purpose
9.4.3A.4 Method of test
9.4.3A.4.1 Initial conditions
9.4.3A.5 Test Requirements
9.4.3B HS-SCCH Type 3 Performance -STTD enabled- Asymmetric CPICHs
9.4.3B.1 Definition and applicability
9.4.3B.2 Minimum requirements
9.4.3B.3 Test purpose
9.4.3B.4 Method of test
9.4.3B.4.1 Initial conditions
9.4.3B.4.2 Procedure
9.4.3B.5 Test Requirements
9.4.4 HS-SCCH Type 3 Performance for MIMO only with single-stream restriction
9.4.4.1 Definition and applicability
9.4.4.2 Minimum requirements
9.4.4.3 Test purpose
9.4.4.4 Method of test
9.4.4.4.1 Initial conditions
9.4.4.4.2 Procedure
9.4.4.5 Test Requirements
9.4.4A HS-SCCH Type 3 Performance for MIMO only with single-stream restriction- Enhanced Performance Requirements Type 1
9.4.4A.1 Definition and applicability
9.4.4A.2 Minimum requirements
9.4.4A.3 Test purpose
9.4.4A.4 Method of test
9.4.4A.4.1 Initial conditions
9.4.4A.4.2 Procedure
9.4.4A.5 Test Requirements
9.4.4B HS-SCCH Type 3 Performance for MIMO only with single-stream restriction-STTD disabled-asymmetric CPICHs
9.4.4B.1 Definition and applicability
9.4.4B.2 Minimum requirements
9.4.4B.3 Test purpose
9.4.4B.4 Method of test
9.4.4B.4.1 Initial conditions
9.4.4B.4.2 Procedure
9.4.4B.5 Test Requirements
9.4.4C HS-SCCH Type 3 Performance for MIMO only with single-stream restriction-STTD disabled-asymmetric CPICHs- Enhanced Perfor
9.4.4C.1 Definition and applicability
9.4.4C.2 Minimum requirements
9.4.4C.3 Test purpose
9.4.4C.4 Method of test
9.4.4C.4.1 Initial conditions
9.4.4C.4.2 Procedure
9.4.4C.5 Test Requirements
9.4.4D HS-SCCH Type 3 Performance for MIMO only with single-stream restriction-STTD enabled-asymmetric CPICHs
9.4.4D.1 Definition and applicability
9.4.4D.2 Minimum requirements
9.4.4D.3 Test purpose
9.4.4D.4 Method of test
9.4.4D.4.1 Initial conditions
9.4.4D.4.2 Procedure
9.4.4D.5 Test Requirements
9.4.4E HS-SCCH Type 3 Performance for MIMO only with single-stream restriction-STTD enabled-asymmetric CPICHs- Enhanced Perform
9.4.4E.1 Definition and applicability
9.4.4E.2 Minimum requirements
9.4.4E.3 Test purpose
9.4.4E.4 Method of test
9.4.4E.4.1 Initial conditions
9.4.4E.4.2 Procedure
9.4.4E.5 Test Requirements
9.5 HS-SCCH-less demodulation of HS-DSCH (Fixed Reference Channel)
9.5.1 Requirement QPSK, Fixed Reference Channel (FRC) H-Set 7
9.5.1.1 Definition and applicability
9.5.1.2 Minimum requirements
9.5.1.3 Test purpose
9.5.1.4 Method of test
9.5.1.5 Test Requirements
9.5.1A Requirement QPSK, Fixed Reference Channel (FRC) H-Set 7 - Enhanced Performance Requirements Type 1
9.5.1A.1 Definition and applicability
9.5.1A.2 Minimum requirements
9.5.1A.3 Test purpose
9.5.1A.4 Method of test
9.5.1A.5 Test Requirements
9.6 HS-DSCH and HS-SCCH reception in CELL-FACH state
9.6.1 Single link HS-DSCH Demodulation performance in CELL_FACH state
9.6.1.1 Definition and applicability
9.6.1.2 Minimum requirement QPSK, Fixed Reference Channel (FRC) H-Set 3
9.6.1.3 Test purpose
9.6.1.4 Method of test
9.6.1.5 Test Requirements
9.6.2 Single link HS-SCCH Detection performance in CELL_FACH state
9.6.2.1 Definition and applicability
9.6.2.2 Minimum requirement
9.6.2.3 Test purpose
9.6.2.4 Method of test
9.6.2.5 Test Requirements
10 Performance requirement (E-DCH)
10.1 General
10.2 Detection of E-DCH HARQ ACK Indicator Channel (E-HICH)
10.2.1 Single link performance
10.2.1.1 Single link performance (10ms TTI)
10.2.1.1.1 Definition and applicability
10.2.1.1.2 Minimum requirement
10.2.1.1.3 Test purpose
10.2.1.1.4 Method of test
10.2.1.1.4.1 Initial conditions
10.2.1.1.4.2 Procedure
10.2.1.1.5. Test requirements
10.2.1.1A Single link performance (10ms TTI, Type 1)
10.2.1.1A.1 Definition and applicability
10.2.1.1A.2 Minimum requirement
10.2.1.1A.3 Test purpose
10.2.1.1A.4 Method of test
10.2.1.1A.4.1 Initial conditions
10.2.1.1A.4.2 Procedure
10.2.1.1A.5. Test requirements
10.2.1.2 Single link performance (2ms TTI)
10.2.1.2.1 Definition and applicability
10.2.1.2.2 Minimum requirement
10.2.1.2.3 Test purpose
10.2.1.2.4 Method of test
10.2.1.2.4.1 Initial conditions
10.2.1.2.4.2 Procedure
10.2.1.2.5. Test requirements
10.2.1.2A Single link performance (2ms TTI, Type 1)
10.2.1.2A.1 Definition and applicability
10.2.1.2A.2 Minimum requirement
10.2.1.2A.3 Test purpose
10.2.1.2A.4 Method of test
10.2.1.2A.4.1 Initial conditions
10.2.1.2A.4.2 Procedure
10.2.1.2A.5. Test requirements
10.2.2 Detection in Inter-Cell Handover conditions
10.2.2.1 RLS not containing the Serving E-DCH cell
10.2.2.1.1 RLS not containing the Serving E-DCH cell (10ms TTI)
10.2.2.1.1.1 Definition and applicability
10.2.2.1.1.2 Minimum requirement
10.2.2.1.1.3 Test Purpose
10.2.2.1.1.4 Method of test
10.2.2.1.1.5 Test Requirements
10.2.2.1.1A RLS not containing the Serving E-DCH cell (10ms TTI, Type 1)
10.2.2.1.1A.1 Definition and applicability
10.2.2.1.1A.2 Minimum requirement
10.2.2.1.1A.3 Test Purpose
10.2.2.1.1A.4 Method of test
10.2.2.1.1A.5 Test Requirements
10.2.2.1.2 RLS not containing the Serving E-DCH cell (2ms TTI)
10.2.2.1.2.1 Definition and applicability
10.2.2.1.2.2 Minimum requirement
10.2.2.1.2.3 Test Purpose
10.2.2.1.2.4 Method of test
10.2.2.1.2.4.1 Initial conditions
10.2.2.1.2.4.2 Procedure
10.2.2.1.2.5 Test Requirements
10.2.2.1.2A RLS not containing the Serving E-DCH cell (2ms TTI, Type 1)
10.2.2.1.2A.1 Definition and applicability
10.2.2.1.2A.2 Minimum requirement
10.2.2.1.2A.3 Test Purpose
10.2.2.1.2A.4 Method of test
10.2.2.1.2A.4.1 Initial conditions
10.2.2.1.2A.4.2 Procedure
10.2.2.1.2A.5 Test Requirements
10.2.2.2 RLS containing the Serving E-DCH cell
10.2.2.2.1 RLS containing the Serving E-DCH cell (10ms TTI)
10.2.2.2.1.1 Definition and applicability
10.2.2.2.1.2 Minimum requirement
10.2.2.2.1.3 Test purpose
10.2.2.2.1.4 Method of test
10.2.2.2.1.4.1 Initial conditions
10.2.2.2.1.4.2 Procedure
10.2.2.2.1.5 Test requirements
10.2.2.2.1A RLS containing the Serving E-DCH cell (10ms TTI, Type 1)
10.2.2.2.1A.1 Definition and applicability
10.2.2.2.1A.2 Minimum requirement
10.2.2.2.1A.3 Test purpose
10.2.2.2.1A.4 Method of test
10.2.2.2.1A.4.1 Initial conditions
10.2.2.2.1A.4.2 Procedure
10.2.2.2.1A.5 Test requirements
10.2.2.2.2 RLS containing the Serving E-DCH cell (2ms TTI)
10.2.2.2.2.1 Definition and applicability
10.2.2.2.2.2 Minimum requirement
10.2.2.2.2.3 Test purpose
10.2.2.2.2.4 Method of test
10.2.2.2.2.4.1 Initial conditions
10.2.2.2.2.4.2 Procedure
10.2.2.2.2.5 Test requirements
10.2.2.2.2A RLS containing the Serving E-DCH cell (2ms TTI, Type 1)
10.2.2.2.2A.1 Definition and applicability
10.2.2.2.2A.2 Minimum requirement
10.2.2.2.2A.3 Test purpose
10.2.2.2.2A.4 Method of test
10.2.2.2.2A.4.1 Initial conditions
10.2.2.2.2A.4.2 Procedure
10.2.2.2.2A.5 Test requirements
10.3 Detection of E-DCH Relative Grant Channel (E-RGCH)
10.3.1 Single link performance
10.3.1.1 Single link performance (10ms TTI)
10.3.1.1.1 Definition and applicability
10.3.1.1.2 Minimum requirement
10.3.1.1.3 Test purpose
10.3.1.1.4 Method of test
10.3.1.1.4.1 Initial conditions
10.3.1.1.4.2 Procedure
10.3.1.1.5 Test requirements
10.3.1.1A Single link performance (10ms TTI, Type 1)
10.3.1.1A.1 Definition and applicability
10.3.1.1A.2 Minimum requirement
10.3.1.1A.3 Test purpose
10.3.1.1A.4 Method of test
10.3.1.1A.4.1 Initial conditions
10.3.1.1A.4.2 Procedure
10.3.1.1A.5 Test requirements
10.3.1.2 Single link performance (2ms TTI)
10.3.1.2.1 Definition and applicability
10.3.1.2.2 Minimum requirement
10.3.1.2.3 Test purpose
10.3.1.2.4 Method of test
10.3.1.2.4.1 Initial conditions
10.3.1.2.4.2 Procedure
10.3.1.2.5 Test requirements
10.3.1.2A Single link performance (2ms TTI, Type 1)
10.3.1.2A.1 Definition and applicability
10.3.1.2A.2 Minimum requirement
10.3.1.2A.3 Test purpose
10.3.1.2A.4 Method of test
10.3.1.2A.4.1 Initial conditions
10.3.1.2A.4.2 Procedure
10.3.1.2A.5 Test requirements
10.3.2 Detection in Inter-Cell Handover conditions
10.3.2.1 Definition and applicability
10.3.2.2 Minimum requirement for Non-serving E-DCH RL
10.3.2.3 Test Purpose
10.3.2.4 Method of test
10.3.2.4.1 Initial conditions
10.3.2.4.2 Procedure
10.3.2.5 Test Requirements
10.3.2A Detection in Inter-Cell Handover conditions (Type 1)
10.3.2A.1 Definition and applicability
10.3.2A.2 Minimum requirement for Non-serving E-DCH RL
10.3.2A.3 Test Purpose
10.3.2A.4 Method of test
10.3.2A.4.1 Initial conditions
10.3.2A.4.2 Procedure
10.3.2A.5 Test Requirements
10.4 Demodulation of E-DCH Absolute Grant Channel (E-AGCH)
10.4.1 Single link performance
10.4.1.1 Definition and applicability
10.4.1.2 Minimum requirement
10.4.1.3 Test Purpose
10.4.1.4 Method of test
10.4.1.4.1 Initial conditions
10.4.1.4.2 Procedure
10.4.1.5 Test Requirements
10.4.1A Single link performance (Type 1)
10.4.1A.1 Definition and applicability
10.4.1A.2 Minimum requirement
10.4.1A.3 Test Purpose
10.4.1A.4 Method of test
10.4.1A.4.1 Initial conditions
10.4.1A.4.2 Procedure
10.4.1A.5 Test Requirements
11 Performance requirement (MBMS)
11.1 General
11.2 Demodulation of MTCH
11.2.1 Definition and applicability
11.2.2 Minimum requirement
11.2.3 Test Purpose
11.2.4 Method of test
11.2.4.1 Initial conditions
11.2.4.2 Procedure
11.2.5 Test Requirements
11.2A Demodulation of MTCH - Enhanced Performance Requirements Type 1
11.2A.1 Definition and applicability
11.2A.2 Minimum requirement
11.2A.3 Test Purpose
11.2A.4 Method of test
11.2A.4.1 Initial conditions
11.2A.4.2 Procedure
11.2A.5 Test Requirements
11.3 Demodulation of MTCH and cell identification
11.3.1 Definition and applicability
11.3.2 Minimum requirements
11.3.3 Test purpose
11.3.4 Method of test
11.3.5 Test requirements
Annex A (informative): Connection Diagrams
Annex B (normative): Global In-Channel TX-Test
B.1 General
B.2 Definition of the process
B.2.1 Basic principle
B.2.2 Output signal of the TX under test
B.2.3 Reference signal
B.2.4 void
B.2.5 Classification of measurement results
B.2.6 Process definition to achieve results f, t, (, g1, g2, and O
B.2.6.1 Decision Point Power
B.2.6.2 Measured total power of all active codes
B.2.6.3 Code-Domain Power
B.2.6.4 Code-Domain Power of the varied reference signal
B.2.7 Process definition to achieve results EVM, PCDE, RCDE
B.2.7.1 Error Vector Magnitude (EVM)
B.2.7.2 Code Domain Error Power
B.2.7.3 Relative Code Domain Error (RCDE)
B.3 Notes
Annex C (normative): Measurement channels
C.1 General
C.2 UL reference measurement channel
C.2.1 UL reference measurement channel (12,2 kbps)
C.2.2 UL reference measurement channel (64 kbps)
C.2.3 UL reference measurement channel (144 kbps)
C.2.4 UL reference measurement channel (384 kbps)
C.2.5 UL reference measurement channel (768 kbps)
C.2.6 UL E-DCH reference measurement channel for DC-HSUPA using BPSK modulation
C.2.7 UL E-DCH reference measurement channel for DC-HSUPA using 16QAM modulation
C.2.8 Combinations of UL E-DCH reference measurement channel for DC-HSUPA tests
C.3 DL reference measurement channel
C.3.1 DL reference measurement channel (12.2 kbps)
C.3.1A DL reference measurement channel (0 kbps and 12.2 kbps)
C.3.2 DL reference measurement channel (64 kbps)
C.3.3 DL reference measurement channel (144 kbps)
C.3.4 DL reference measurement channel (384 kbps)
C.3.5 DL reference measurement channel 2 (64 kbps)
C.4 Reference measurement channel for BTFD performance requirements
C.4.1 UL reference measurement channel for BTFD performance requirements
C.4.2 DL reference measurement channel for BTFD performance requirements
C.4.3 Reference parameters for discontinuous UL DPCCH transmission
C.5 DL reference compressed mode parameters
C.6 Auxiliary measurement channels
C.6.1 Introduction
C.6.2 Channel combinations for BLER measurements
C.6.3 UL auxiliary reference measurement channel (TM, 12.2 kbps, no CRC)
C.6.3A UL auxiliary reference measurement channel (TM, 0 kbps and 12.2 kbps, no CRC)
C.6.4 Void
C.6.5 Void
C.6.6 Void
C.6.7 UL AUXMC AM 12.2 kbps
C.6.8 UL AUXMC AM 12.2 kbps(DCCH with TB size of 148bit)
C.7 DL reference parameters for PCH tests
C.8 DL reference channel parameters for HSDPA tests
C.8.1 Fixed Reference Channel (FRC)
C.8.1.1 Fixed Reference Channel Definition H-Set 1/1A/1B/1C
C.8.1.2 Fixed Reference Channel Definition H-Set 2
C.8.1.3 Fixed Reference Channel Definition H-Set 3/3A/3B/3C
C.8.1.4 Fixed Reference Channel Definition H-Set 4
C.8.1.5 Fixed Reference Channel Definition H-Set 5
C.8.1.6 Fixed Reference Channel Definition H-Set 6/6A/6B/6C
C.8.1.7 Fixed Reference Channel Definition H-Set 7
C.8.1.8 Fixed Reference Channel Definition H-Set 8/8A/8B/8C
C.8.1.9 Fixed Reference Channel Definition H-Set 9/9A/9B/9C
C.8.1.10 Fixed Reference Channel Definition H-Set 10/10A/10B/10C
C.8.1.11 Fixed Reference Channel Definition H-Set 11/11A/11B/11C
C.8.1.12 Fixed Reference Channel Definition H-Set 12
C.9 Downlink reference channel dummy DCCH transmission on DCH
C.9A MAC header transmission on HS-DSCH
C.10 UL reference channel parameters for HSDPA tests
C.10.1 UL reference measurement channel for HSDPA tests
C.10.2 UL reference measurement channel for HSDPA tests with UL OLTD/CLTD
C.11 Reference channel parameters for E-DCH tests
C.11.1 UL reference measurement channel for E-DCH tests
C.11.1A UL reference measurement channel for E-DCH tests with UL OLTD/CLTD
C.11.2 DL reference measurement channel for E-DCH tests
C.11.3 RLC SDU size for E-DCH tests
C.11A Reference channel parameters for DC-HSUPA tests
C.11A.1 UL reference measurement channel for DC-HSUPA tests
C.11A.2 DL reference measurement channel for DC-HSUPA tests
C.11A.3 RLC SDU size for DC-HSUPA tests
C.12 DL reference parameters for MBMS tests
C.12.1 MTCH
C.12.2 Combined MTCH demodulation and cell identification
Annex D (normative): Propagation Conditions
D.1 General
D.1.1 Definition of Additive White Gaussian Noise (AWGN) Interferer
D.2 Propagation Conditions
D.2.1 Static propagation condition
D.2.2 Multi-path fading propagation conditions
D.2.3 Moving propagation conditions
D.2.4 Birth-Death propagation conditions
D.2.4A High speed train conditions
D.2.5 Conditions for HSDPA enhanced performance requirements type 1 with UE receiver diversity
D.2.6 Conditions for HSDPA enhanced performance requirements type 3 with UE receiver diversity
D.2.7 Conditions for open and closed loop diversity performance
D.2.8 Conditions for MBMS enhanced performance requirements type 1 with UE receiver diversity
D.2.9 MIMO propagation conditions
D.2.9.1 MIMO Single Stream Fading Conditions
D.2.9.2 MIMO Dual Stream Fading Conditions
D.2.9.3 MIMO Dual Stream Static Orthogonal Conditions
Annex E (normative): Downlink Physical Channels
E.1 General
E.2 Connection Set-up for non-HSDPA test cases
E.2.1 Measurement without dedicated connection
E.3 During connection for non-HSDPA test cases
E.3.1 Measurement of Tx Characteristics
E.3.2 Measurement of Rx Characteristics
E.3.3 Measurement of Performance requirements
E.3.4 Connection with open-loop transmit diversity mode
E.3.5 Connection with closed loop transmit diversity mode
E.3.6 OCNS Definition
E.4 W-CDMA Modulated Interferer for non-HSDPA test cases
E.5 HSDPA DL Physical channels
E.5.0 Downlink Physical Channels for connection set-up
E.5.1 Downlink Physical Channels for measurement
E.5.2 HSDPA OCNS Definition
E.5.3 Downlink Physical Channels for measurement including test tolerances
E.5.4 Downlink Physical Channels for Transmitter Characteristics with HS-DPCCH
E.5A E-DCH with HSDPA DL Physical channels
E.5A.0 Downlink Physical Channels for connection set-up
E.5A.1 Downlink Physical Channels for measurement
E.5A.2 E-DCH OCNS Definition
E.5B MBMS DL Physical channels
E.5B.1 Downlink Physical Channels for connection set-up
E.5C F-DPCH with HSDPA DL Physical channels
E.5C.0 Downlink Physical Channels for connection set-up
E.5C.1 Downlink Physical Channels for measurement
E.5D HSDPA and E-DCH DL Physical channels with discontinuous UL DPCCH transmission
E.5D.0 Downlink Physical Channels for connection set-up
E.5D.1 Downlink Physical Channels for measurement
E.5E Test Definition for Enhanced Performance Type 3i
E.5E.1 Transmitted code and power characteristics for serving cell
E.5E.2 Transmitted code and power characteristics for interfering cells
E.5E.3 Model for power control sequence generation
E.5F Test Definition for MultiFlow HSDPA
E.5F.1 Test configuration when 2 cells are configured in Multiflow mode
E.5F.2 Test configuration when 3 cells are configured in Multiflow mode
E.5F.3 Test configuration when 4 cells are configured in Multiflow mode
E.6 Downlink Physical Channels Code Allocation (This clause is informative)
E.6.1 Downlink Physical Channels Code Allocation for non-HSDPA test cases
E.6.2 Downlink Physical Channels Code Allocation for HSDPA test cases
E.6.3 Downlink Physical Channels Code Allocation for E-DCH test cases
E.6.4 Downlink Physical Channels Code Allocation for MBMS test cases
Annex F (normative): General test conditions and declarations
F.1 Acceptable uncertainty of Test System
F.1.1 Measurement of test environments
F.1.2 Measurement of transmitter
F.1.3 Measurement of receiver
F.1.4 Performance requirement
F.1.5 Requirements for support of RRM
F.1.6 Performance requirement (HSDPA)
F.1.7 Performance requirement (E-DCH)
F.1.8 Performance requirement (MBMS)
F.2 Test Tolerances (This clause is informative)
F.2.1 Transmitter
F.2.2 Receiver
F.2.3 Performance requirements
F.2.4 Requirements for support of RRM
F.2.5 Performance requirements (HSDPA)
F.2.6 Performance requirements (E-DCH)
F.2.7 Performance requirements (MBMS)
F.3 Interpretation of measurement results
F.4 Derivation of Test Requirements (This clause is informative)
F.4.1 Transmitter
F.4.2 Receiver
F.4.3 Performance requirements
F.4.4 Requirements for support of RRM
F.4.5 Performance requirements (HSDPA)
F.4.6 Performance requirements (E-DCH)
F.4.7 Performance requirements (MBMS)
F.5 Acceptable uncertainty of Test Equipment (This clause is informative)
F.5.1 Transmitter measurements
F.5.2 Receiver measurements
F.5.3 Performance measurements
F.5.4 Requirements for support of RRM
F.5.5 Performance measurements (HSDPA)
F.5.6 Performance measurements (E-DCH)
F.5.7 Performance measurements (MBMS)
F.6 General rules for statistical testing
F.6.1 Statistical testing of receiver BER/BLER performance
F.6.1.1 Error Definition
F.6.1.2 Test Method
F.6.1.3 Test Criteria
F.6.1.4 Calculation assumptions
F.6.1.4.1 Statistical independence
F.6.1.4.2 Applied formulas
F.6.1.4.3 Approximation of the distribution
F.6.1.5 Definition of good pass fail decision.
F.6.1.6 Good balance between test time and statistical significance
F.6.1.7 Pass fail decision rules
F.6.1.8 Test conditions for BER, BLER, RLC SDU Error Rate tests
F.6.1.9 Practical Use (informative)
F.6.1.10 Dual limit BLER tests
F.6.1.10.1 Description of the parameters for dual limit BLER tests
F.6.1.10.2 Pass fail decision rules
F.6.1.10.3 Test conditions for dual limit BLER tests
F.6.1.10.4 Test conditions for dual limit TPC Command Error Rate tests
F.6.2 Statistical testing of RRM delay performance
F.6.2.1 Test Method
F.6.2.2 Bad Delay Ratio (ER)
F.6.2.3 Test Criteria
F.6.2.4 Calculation assumptions
F.6.2.4.1 Statistical independence
F.6.2.4.2 Applied formulas
F.6.2.4.3 Approximation of the distribution
F.6.2.5 Definition of good pass fail decision
F.6.2.6 Good balance between test-time and statistical significance
F.6.2.7 Pass fail decision rules
F.6.2.8 Test conditions for RRM delay tests, Combining of TPC commands test 1, Demodulation of Paging channel and Detection of acquisition indicator tests and UE measurement performance tests.
F.6.2.9 Practical Use (informative)
F.6.3 Statistical Testing of HSDPA Receiver Performance
F.6.3.1 Definition
F.6.3.2 Mapping throughput to block error ratio
F.6.3.3 Bad DUT factor
F.6.3.3.1 Bad DUT factor, range of applicability
F.6.3.4 Minimum Test time
F.6.3.5 Test conditions for HSDPA Receiver Performance
F.6.4 Statistical testing of performance requirement (E-DCH and MBMS)
F.6.4.1 Test Method
F.6.4.2 Bad Result Ratio (ER)
F.6.4.3 Mapping of E-DCH and MBMS tests to RRM tests (F.6.2) and HSDPA tests (F.6.3)
F.6.4.4 Test conditions for E-DCH tests and MBMS
Annex G (normative): Environmental conditions
G.1 General
G.2 Environmental requirements
G.2.1 Temperature
G.2.2 Voltage
G.2.3 Vibration
G.2.4 Specified frequency range
Annex H (normative): UE Capabilities (FDD)
H.1 Void
H.2 Void
Annex I (normative): Default Message Contents
Contents of MEASUREMENT REPORT message for Intra frequency test cases
Contents of MEASUREMENT REPORT message for Inter frequency test cases
Contents of MEASUREMENT REPORT message for inter ΠRAT test cases
Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_DCH)
Contents of RADIO BEARER SETUP message: AM or UM (HSDPA)
Contents of Master Information Block PLMN type is the case of GSM-MAP
Contents of Scheduling Block 1 (FDD)
Contents of Scheduling Block 1 (FDD)
Contents of Scheduling Block 1 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of Scheduling Block 1 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of Scheduling Block 1 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of System Information Block type 11 (FDD)
Contents of ACTIVE SET UPDATE message for test cases with SHO in clauses 7.7.1, 7.7.1A, 7.7.2, and 7.7.3.
Annex J (informative): Information about special regional application of test cases and requirements
J.1 Japan
Annex K (normative): Cell configuration mapping
Annex L (normative): Conditions for RRM requirements applicability for operating bands
L.1 Conditions for Idle mode tasks
L.1.1 Conditions for measurements of inter-RAT E-UTRA cells
L.2 Conditions for UE Measurements Procedures
L.2.1 Conditions for E-UTRAN measurements
L.3 Conditions for Measurement Performance for UE
L.3.1 Conditions for intra frequency CPICH RSCP measurements accuracy
L.3.2 Conditions for intra frequency CPICH RSCP relative measurements accuracy
L.3.3 Conditions for inter frequency CPICH RSCP relative measurements accuracy
L.3.4 Conditions for intra frequency CPICH Ec/Io measurements accuracy
L.3.5 Conditions for intra frequency CPICH Ec/Io relative measurements accuracy
L.3.6 Conditions for inter frequency CPICH Ec/Io measurements accuracy
L.3.7 Conditions for inter frequency CPICH Ec/Io relative measurements accuracy
L.3.8 Conditions for intra frequency SFN-SFN observed time difference
L.3.9 Conditions for inter frequency SFN-SFN observed time difference
L.3.10 Conditions for SFN-SFN observed time difference type 1
L.3.11 Conditions for intra frequency SFN-SFN observed time difference type 2 without or with IPDL period active
L.3.12 Conditions for inter frequency SFN-SFN observed time difference type 2
L.4 Conditions for UTRAN Connected mode mobility
L.4.1 Conditions for identification of a new CGI of inter-RAT E-UTRA cell with autonomous gaps
Annex M (informative): Change history
History
ETSI TS 134 121-1 V15.2.0 (2018-10)
TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) conformance specification;
(3GPP TS 34.121-1 version 15.2.0 Release 15)
Radio transmission and reception (FDD);
Part 1: Conformance specification
3GPP TS 34.121-1 version 15.2.0 Release 15
1
ETSI TS 134 121-1 V15.2.0 (2018-10)
Reference
RTS/TSGR-0534121-1vf20
Keywords
UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
of the oneM2M Partners
© ETSI 2018.
All rights reserved.
ETSI
3GPP TS 34.121-1 version 15.2.0 Release 15
2
ETSI TS 134 121-1 V15.2.0 (2018-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by the ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
http://webapp.etsi.org/key/queryform.asp.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
3GPP TS 34.121-1 version 15.2.0 Release 15
3
ETSI TS 134 121-1 V15.2.0 (2018-10)
Contents
Intellectual Property Rights ................................................................................................................................ 2
Foreword ............................................................................................................................................................. 2
Modal verbs terminology .................................................................................................................................... 2
Foreword ........................................................................................................................................................... 59
Introduction ...................................................................................................................................................... 59
1
2
3
3.1
3.2
3.3
3.4
Scope ...................................................................................................................................................... 60
References .............................................................................................................................................. 60
Definitions, symbols, abbreviations and equations ................................................................................ 62
Definitions ........................................................................................................................................................ 62
Symbols ............................................................................................................................................................ 63
Abbreviations ................................................................................................................................................... 63
Equations .......................................................................................................................................................... 64
4
4.1
4.2
4.3
4.4
4.4.1
4.4.2
4.4.3
4.4.4
Frequency bands and channel arrangement ............................................................................................ 66
General ............................................................................................................................................................. 66
Frequency bands ............................................................................................................................................... 67
TX-RX frequency separation ........................................................................................................................... 68
Channel arrangement ........................................................................................................................................ 68
Channel spacing .......................................................................................................................................... 68
Channel raster ............................................................................................................................................. 69
Channel number .......................................................................................................................................... 69
UARFCN .................................................................................................................................................... 71
4A Reference Conditions ............................................................................................................................. 72
4A.1
Generic setup procedures ................................................................................................................................. 72
System information .......................................................................................................................................... 72
4A.2
Message contents .............................................................................................................................................. 72
4A.3
4A.4
Measurement configurations ............................................................................................................................ 73
5
Transmitter Characteristics ..................................................................................................................... 73
5.1
General ............................................................................................................................................................. 73
5.2
Maximum Output Power .................................................................................................................................. 74
5.2.1
Definition and applicability ........................................................................................................................ 74
5.2.2
Minimum Requirements ............................................................................................................................. 75
5.2.3
Test purpose ................................................................................................................................................ 76
5.2.4
Method of test ............................................................................................................................................. 76
5.2.4.1
Initial conditions ................................................................................................................................... 76
5.2.4.2
Procedure .............................................................................................................................................. 77
5.2.5
Test requirements ........................................................................................................................................ 77
5.2A
Maximum Output Power with HS-DPCCH (Release 5 only) .......................................................................... 78
5.2A.1
Definition and applicability ........................................................................................................................ 78
5.2A.2
Minimum Requirements ............................................................................................................................. 78
5.2A.3
Test purpose ................................................................................................................................................ 78
5.2A.4
Method of test ............................................................................................................................................. 78
5.2A.4.1
Initial conditions ................................................................................................................................... 78
5.2A.4.2
Procedure .............................................................................................................................................. 79
5.2A.5
Test requirements ........................................................................................................................................ 79
5.2AA Maximum Output Power with HS-DPCCH (Release 6 and later) .................................................................... 80
Definition and applicability ........................................................................................................................ 80
5.2AA.1
Minimum Requirements ............................................................................................................................. 80
5.2AA.2
5.2AA.3
Test purpose ................................................................................................................................................ 80
Method of test ............................................................................................................................................. 80
5.2AA.4
Initial conditions ................................................................................................................................... 80
5.2AA.4.1
Procedure .............................................................................................................................................. 81
5.2AA.4.2
5.2AA.5
Test requirements ........................................................................................................................................ 81
ETSI
3GPP TS 34.121-1 version 15.2.0 Release 15
4
ETSI TS 134 121-1 V15.2.0 (2018-10)
5.2AB Maximum Output Power for OLTD ................................................................................................................. 82
Definition and applicability ........................................................................................................................ 82
5.2AB.1
Minimum Requirements ............................................................................................................................. 83
5.2AB.2
Test purpose ................................................................................................................................................ 83
5.2AB.3
Method of test ............................................................................................................................................. 83
5.2AB.4
5.2AB.4.1
Initial conditions ................................................................................................................................... 83
Procedure .............................................................................................................................................. 84
5.2AB.4.2
5.2AB.5
Test requirements ........................................................................................................................................ 84
5.2AC Maximum Output Power for UL CLTD activation state 1 ............................................................................... 86
5.2AC.1
Definition and applicability ........................................................................................................................ 86
Minimum Requirements ............................................................................................................................. 86
5.2AC.2
Test purpose ................................................................................................................................................ 87
5.2AC.3
Method of test ............................................................................................................................................. 87
5.2AC.4
5.2AC.4.1
Initial conditions ................................................................................................................................... 87
Procedure .............................................................................................................................................. 87
5.2AC.4.2
5.2AC.5
Test requirements ........................................................................................................................................ 88
5.2AD Maximum Output Power for UL CLTD activation state 2 and 3 ..................................................................... 89
Definition and applicability ........................................................................................................................ 89
5.2AD.1
5.2AD.2
Minimum Requirements ............................................................................................................................. 89
Test purpose ................................................................................................................................................ 90
5.2AD.3
Method of test ............................................................................................................................................. 90
5.2AD.4
Initial conditions ................................................................................................................................... 90
5.2AD.4.1
5.2AD.4.2
Procedure .............................................................................................................................................. 91
5.2AD.5
Test requirements ........................................................................................................................................ 91
Maximum Output Power with HS-DPCCH and E-DCH.................................................................................. 92
5.2B
Definition and applicability ........................................................................................................................ 92
5.2B.1
5.2B.2
Minimum Requirements ............................................................................................................................. 92
Test purpose ................................................................................................................................................ 93
5.2B.3
Method of test ............................................................................................................................................. 93
5.2B.4
Initial conditions ................................................................................................................................... 93
5.2B.4.1
5.2B.4.2
Procedure .............................................................................................................................................. 95
5.2B.5
Test requirements ........................................................................................................................................ 95
5.2BA UE Maximum Output Power for DC-HSUPA (QPSK).................................................................................... 97
Definition and applicability ........................................................................................................................ 97
5.2BA.1
Minimum Requirements ............................................................................................................................. 97
5.2BA.2
5.2BA.3
Test purpose ................................................................................................................................................ 98
Method of test ............................................................................................................................................. 98
5.2BA.4
Initial conditions ................................................................................................................................... 98
5.2BA.4.1
Procedure .............................................................................................................................................. 99
5.2BA.4.2
5.2BA.5
Test requirements ........................................................................................................................................ 99
5.2BB UE Maximum Output Power for DC-HSUPA (16QAM) .............................................................................. 100
Definition and applicability ...................................................................................................................... 100
5.2BB.1
Minimum Requirements ........................................................................................................................... 101
5.2BB.2
Test purpose .............................................................................................................................................. 102
5.2BB.3
5.2BB.4
Method of test ........................................................................................................................................... 102
Initial conditions ................................................................................................................................. 102
5.2BB.4.1
Procedure ............................................................................................................................................ 102
5.2BB.4.2
5.2BB.5
Test requirements ...................................................................................................................................... 103
5.2BC Maximum Output Power with HS-DPCCH and E-DCH for OLTD .............................................................. 104
Definition and applicability ...................................................................................................................... 104
5.2BC.1
Minimum Requirements ........................................................................................................................... 104
5.2BC.2
Test purpose .............................................................................................................................................. 104
5.2BC.3
Method of test ........................................................................................................................................... 105
5.2BC.4
5.2BC.4.1
Initial conditions ....................................................................................................................................... 105
5.2BC.4.2
Procedure .................................................................................................................................................. 107
5.2BC.4.2.1 Procedure for sub-test 1 to 4 ..................................................................................................................... 107
5.2BC.5
Test requirements ...................................................................................................................................... 107
5.2BD Maximum Output Power with HS-DPCCH and E-DCH for UL CLTD activation state 1 ............................ 108
Definition and applicability ...................................................................................................................... 108
5.2BD.1
Minimum Requirements ........................................................................................................................... 109
5.2BD.2
Test purpose .............................................................................................................................................. 109
5.2BD.3
5.2BD.4
Method of test ........................................................................................................................................... 109
ETSI
3GPP TS 34.121-1 version 15.2.0 Release 15
5
ETSI TS 134 121-1 V15.2.0 (2018-10)
Initial conditions ................................................................................................................................. 109
5.2BD.4.1
Procedure ............................................................................................................................................ 111
5.2BD.4.2
Procedure for sub-test 1 to 4 .......................................................................................................... 111
5.2BD.4.2.1
5.2BD.5
Test requirements ...................................................................................................................................... 112
5.2BE Maximum Output Power with HS-DPCCH and E-DCH for UL CLTD activation state 2 and 3. .................. 113
5.2BE.1
Definition and applicability ...................................................................................................................... 113
Minimum Requirements ........................................................................................................................... 113
5.2BE.2
Test purpose .............................................................................................................................................. 114
5.2BE.3
Method of test ........................................................................................................................................... 114
5.2BE.4
5.2BE.4.1
Initial conditions ................................................................................................................................. 114
Procedure ............................................................................................................................................ 116
5.2BE.4.2
Procedure for sub-test 1 to 4 .......................................................................................................... 116
5.2BE.4.2.1
5.2BE.5
Test requirements ...................................................................................................................................... 116
UE relative code domain power accuracy ...................................................................................................... 118
5.2C
Definition and applicability ...................................................................................................................... 118
5.2C.1
Minimum Requirements ........................................................................................................................... 118
5.2C.2
Test purpose .............................................................................................................................................. 118
5.2C.3
Method of test ........................................................................................................................................... 118
5.2C.4
5.2C.4.1
Initial conditions ................................................................................................................................. 118
Procedure ............................................................................................................................................ 119
5.2C.4.2
5.2C.5
Test requirements ...................................................................................................................................... 120
5.2CA UE relative code domain power accuracy for OLTD ..................................................................................... 121
5.2CA.1
Definition and applicability ...................................................................................................................... 121
Minimum Requirements ........................................................................................................................... 121
5.2CA.2
Test purpose .............................................................................................................................................. 121
5.2CA.3
Method of test ........................................................................................................................................... 121
5.2CA.4
5.2CA.4.1
Initial conditions ................................................................................................................................. 121
Procedure ............................................................................................................................................ 122
5.2CA.4.2
5.2CA.5
Test requirements ...................................................................................................................................... 123
5.2CB UE relative code domain power accuracy for UL CLTD activation state 1 ................................................... 124
Definition and applicability ...................................................................................................................... 124
5.2CB.1
5.2CB.2
Minimum Requirements ........................................................................................................................... 124
Test purpose .............................................................................................................................................. 124
5.2CB.3
Method of test ........................................................................................................................................... 124
5.2CB.4
Initial conditions ................................................................................................................................. 124
5.2CB.4.1
5.2CB.4.2
Procedure ............................................................................................................................................ 125
5.2CB.5
Test requirements ...................................................................................................................................... 126
5.2CC UE relative code domain power accuracy for UL CLTD activation state 2 and 3 ......................................... 127
Definition and applicability ...................................................................................................................... 127
5.2CC.1
5.2CC.2
Minimum Requirements ........................................................................................................................... 127
Test purpose .............................................................................................................................................. 127
5.2CC.3
Method of test ........................................................................................................................................... 127
5.2CC.4
Initial conditions ................................................................................................................................. 127
5.2CC.4.1
Procedure ............................................................................................................................................ 128
5.2CC.4.2
5.2CC.5
Test requirements ...................................................................................................................................... 129
UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH .................................................... 130
5.2D
Definition and applicability ...................................................................................................................... 130
5.2D.1
Minimum Requirements ........................................................................................................................... 130
5.2D.2
5.2D.3
Test purpose .............................................................................................................................................. 130
Method of test ........................................................................................................................................... 131
5.2D.4
Initial conditions ................................................................................................................................. 131
5.2D.4.1
Procedure ............................................................................................................................................ 132
5.2D.4.2
5.2D.5
Test requirements ...................................................................................................................................... 133
5.2DA UE Relative Code Domain Power Accuracy for DC-HSUPA with QPSK .................................................... 134
Definition and applicability ...................................................................................................................... 134
5.2DA.1
Minimum Requirements ........................................................................................................................... 134
5.2DA.2
Test purpose .............................................................................................................................................. 134
5.2DA.3
5.2DA.4
Method of test ........................................................................................................................................... 135
Initial conditions ................................................................................................................................. 135
5.2DA.4.1
Procedure ............................................................................................................................................ 135
5.2DA.4.2
5.2DA.5
Test requirements ...................................................................................................................................... 136
5.2DB UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH for OLTD .................................. 136
ETSI
3GPP TS 34.121-1 version 15.2.0 Release 15
6
ETSI TS 134 121-1 V15.2.0 (2018-10)
5.2DB.1
5.2DB.2
5.2DB.3
5.2DB.4
5.2DB.4.1
5.2DB.4.2
5.2DB.5
5.2DC UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH for UL CLTD activation state
Definition and applicability ...................................................................................................................... 136
Minimum Requirements ........................................................................................................................... 137
Test purpose .............................................................................................................................................. 137
Method of test ........................................................................................................................................... 137
Initial conditions ................................................................................................................................. 137
Procedure ............................................................................................................................................ 139
Test requirements ...................................................................................................................................... 139
1 ...................................................................................................................................................................... 140
Definition and applicability ...................................................................................................................... 140
Minimum Requirements ........................................................................................................................... 141
Test purpose .............................................................................................................................................. 141
Method of test ........................................................................................................................................... 141
Initial conditions ................................................................................................................................. 141
Procedure ............................................................................................................................................ 143
Test requirements ...................................................................................................................................... 143
5.2DC.1
5.2DC.2
5.2DC.3
5.2DC.4
5.2DC.4.1
5.2DC.4.2
5.2DC.5
5.2DD UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH for UL CLTD activation state
2 and 3 ............................................................................................................................................................ 144
Definition and applicability ...................................................................................................................... 144
5.2DD.1
Minimum Requirements ........................................................................................................................... 144
5.2DD.2
Test purpose .............................................................................................................................................. 145
5.2DD.3
Method of test ........................................................................................................................................... 145
5.2DD.4
Initial conditions ................................................................................................................................. 145
5.2DD.4.1
Procedure ............................................................................................................................................ 147
5.2DD.4.2
Test requirements ...................................................................................................................................... 148
5.2DD.5
UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM ............................. 148
5.2E
Definition and applicability ...................................................................................................................... 148
5.2E.1
Minimum Requirements ........................................................................................................................... 149
5.2E.2
Test purpose .............................................................................................................................................. 149
5.2E.3
Method of test ........................................................................................................................................... 149
5.2E.4
Initial conditions ................................................................................................................................. 149
5.2E.4.1
Procedure ............................................................................................................................................ 150
5.2E.4.2
5.2E.5
Test requirements ...................................................................................................................................... 151
5.2EA UE Relative Code Domain Power Accuracy for DC-HSUPA with 16QAM ................................................. 152
Definition and applicability ...................................................................................................................... 152
5.2EA.1
5.2EA.2
Minimum Requirements ........................................................................................................................... 152
Test purpose .............................................................................................................................................. 152
5.2EA.3
Method of test ........................................................................................................................................... 153
5.2EA.4
Initial conditions ................................................................................................................................. 153
5.2EA.4.1
5.2EA.4.2
Procedure ............................................................................................................................................ 153
5.2EA.5
Test requirements ...................................................................................................................................... 154
UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM for OLTD ............ 154
5.2EB
Definition and applicability ...................................................................................................................... 154
5.2EB.1
Minimum Requirements ........................................................................................................................... 155
5.2EB.2
5.2EB.3
Test purpose .............................................................................................................................................. 155
Method of test ........................................................................................................................................... 155
5.2EB.4
Initial conditions ................................................................................................................................. 155
5.2EB.4.1
Procedure ............................................................................................................................................ 156
5.2EB.4.2
5.2EB.5
Test requirements ...................................................................................................................................... 157
5.2EC
UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM for UL CLTD
activation state 1 ............................................................................................................................................. 158
Definition and applicability ...................................................................................................................... 158
Minimum Requirements ........................................................................................................................... 158
Test purpose .............................................................................................................................................. 159
Method of test ........................................................................................................................................... 159
Initial conditions ................................................................................................................................. 159
Procedure ............................................................................................................................................ 160
Test requirements ...................................................................................................................................... 161
5.2EC.1
5.2EC.2
5.2EC.3
5.2EC.4
5.2EC.4.1
5.2EC.4.2
5.2EC.5
5.2ED UE Relative Code Domain Power Accuracy for HS-DPCCH and E-DCH with 16QAM for UL CLTD
5.2ED.1
5.2ED.2
activation state 2 and 3 ................................................................................................................................... 162
Definition and applicability ...................................................................................................................... 162
Minimum Requirements ........................................................................................................................... 162
ETSI
3GPP TS 34.121-1 version 15.2.0 Release 15
7
ETSI TS 134 121-1 V15.2.0 (2018-10)
5.2ED.3
5.2ED.4
5.2ED.4.1
5.2ED.4.2
5.2ED.5
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.3.4.1
5.3.4.2
5.3.5
5.3A
5.3A.1
5.3A.2
5.3A.3
5.3A.4
5.3A.4.1
5.3A.4.2
5.3A.5
5.3B
5.3B.1
5.3B.2
5.3B.3
5.3B.4
5.3B.4.1
5.3B.4.2
5.3B.5
5.3C
5.3C.1
5.3C.2
5.3C.3
5.3C.4
5.3C.4.1
5.3C.4.2
5.3C.5
5.3D
5.3D.1
5.3D.2
5.3D.3
5.3D.4
5.3D.4.1
5.3D.4.2
5.3D.5
5.4
5.4.1
5.4.1.1
5.4.1.2
5.4.1.3
5.4.1.4
5.4.1.5
5.4.1A
5.4.1A.1
5.4.1A.2
5.4.1A.3
5.4.1A.4
5.4.1A.5
5.4.2
5.4.2.1
5.4.2.2
5.4.2.3
Test purpose .............................................................................................................................................. 162
Method of test ........................................................................................................................................... 163
Initial conditions ................................................................................................................................. 163
Procedure ............................................................................................................................................ 164
Test requirements ...................................................................................................................................... 165
Frequency Error .............................................................................................................................................. 165
Definition and applicability ...................................................................................................................... 165
Minimum Requirements ........................................................................................................................... 166
Test purpose .............................................................................................................................................. 166
Method of test ........................................................................................................................................... 166
Initial conditions ................................................................................................................................. 166
Procedure ............................................................................................................................................ 166
Test Requirements .................................................................................................................................... 166
Frequency Error for DC-HSUPA ................................................................................................................... 166
Definition and applicability ...................................................................................................................... 166
Minimum Requirements ........................................................................................................................... 167
Test purpose .............................................................................................................................................. 167
Method of test ........................................................................................................................................... 167
Initial conditions ................................................................................................................................. 167
Procedure ............................................................................................................................................ 167
Test Requirements .................................................................................................................................... 167
Frequency Error for OLTD ............................................................................................................................ 168
Definition and applicability ...................................................................................................................... 168
Minimum Requirements ........................................................................................................................... 168
Test purpose .............................................................................................................................................. 168
Method of test ........................................................................................................................................... 168
Initial conditions ................................................................................................................................. 168
Procedure ............................................................................................................................................ 169
Test Requirements .................................................................................................................................... 169
Frequency Error for UL CLTD Activation state 1 ......................................................................................... 169
Definition and applicability ...................................................................................................................... 169
Minimum Requirements ........................................................................................................................... 169
Test purpose .............................................................................................................................................. 169
Method of test ........................................................................................................................................... 170
Initial conditions ................................................................................................................................. 170
Procedure ............................................................................................................................................ 170
Test Requirements .................................................................................................................................... 171
Frequency Error for UL CLTD Activation state 2 and 3 ................................................................................ 171
Definition and applicability ...................................................................................................................... 171
Minimum Requirements ........................................................................................................................... 171
Test purpose .............................................................................................................................................. 171
Method of test ........................................................................................................................................... 171
Initial conditions ................................................................................................................................. 171
Procedure ............................................................................................................................................ 172
Test Requirements .................................................................................................................................... 172
Output Power Dynamics in the Uplink ........................................................................................................... 172
Open Loop Power Control in the Uplink .................................................................................................. 172
Definition and applicability ................................................................................................................. 172
Minimum requirements ....................................................................................................................... 172
Test purpose ........................................................................................................................................ 173
Method of test ..................................................................................................................................... 173
Test requirements ................................................................................................................................ 174
Open Loop Power Control in the Uplink for DC-HSUPA........................................................................ 175
Definition and applicability ................................................................................................................. 175
Minimum requirements ....................................................................................................................... 175
Test purpose ........................................................................................................................................ 175
Method of test ..................................................................................................................................... 175
Test requirements ................................................................................................................................ 177
Inner Loop Power Control in the Uplink .................................................................................................. 177
Definition and applicability ................................................................................................................. 177
Minimum requirements ....................................................................................................................... 177
Test purpose ........................................................................................................................................ 178
ETSI
相关推荐
2023年江西萍乡中考道德与法治真题及答案.doc
2012年重庆南川中考生物真题及答案.doc
2013年江西师范大学地理学综合及文艺理论基础考研真题.doc
2020年四川甘孜小升初语文真题及答案I卷.doc
2020年注册岩土工程师专业基础考试真题及答案.doc
2023-2024学年福建省厦门市九年级上学期数学月考试题及答案.doc
2021-2022学年辽宁省沈阳市大东区九年级上学期语文期末试题及答案.doc
2022-2023学年北京东城区初三第一学期物理期末试卷及答案.doc
2018上半年江西教师资格初中地理学科知识与教学能力真题及答案.doc
2012年河北国家公务员申论考试真题及答案-省级.doc
2020-2021学年江苏省扬州市江都区邵樊片九年级上学期数学第一次质量检测试题及答案.doc
2022下半年黑龙江教师资格证中学综合素质真题及答案.doc
