昂达主板-P4GE说明书.pdf

发布时间：2022-05-12 发布人：admin 分类：说明书资料大小：0.44M 资料格式：pdf 举报版权申诉

第1页 / 共16页

第2页 / 共16页

第3页 / 共16页

第4页 / 共16页

第5页 / 共16页

第6页 / 共16页

第7页 / 共16页

第8页 / 共16页

文本预览

11111 Electronic Emission Notices Electronic Emission Notices Electronic Emission Notices Electronic Emission Notices Electronic Emission Notices Federal Communications Commission (FCC) Statement (207828) Federal Communications Commission (FCC) Statement (207828) Federal Communications Commission (FCC) Statement (207828) Federal Communications Commission (FCC) Statement (207828) Federal Communications Commission (FCC) Statement (207828) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - REORIENT OR RELOCATE THE RECEIVING ANTENNA - INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER - CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER - CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. Copyright Copyright Copyright Copyright Copyright This manual is copyrighted with all rights reserved. No portion of this manual may be copied or reproduced by any means. While every precaution has been taken in the preparation of this manual, no responsibility for errors or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the information contained herein. Trademarks Trademarks Trademarks Trademarks Trademarks All brand names, logos and registered trademarks mentioned are property of their respective owners.

22222 able of Contents able of Contents TTTTTable of Contents able of Contents able of Contents HARDWARE CONFIGURATION HARDWARE CONFIGURATION .................................................................... .................................................................... .................................................................... 33333 HARDWARE CONFIGURATION .................................................................... .................................................................... HARDWARE CONFIGURATION HARDWARE CONFIGURATION Key Features ............................................................................................................... 3 Motherboard Layout .................................................................................................... 6 Jumper Settings ........................................................................................................... 7 CPU Speed Selection ............................................................................................ 7 JP1 - System Bus Frequency(only for 845G/GE/PE/GV) .................................... 7 JP2 - CMOS Clear .................................................................................................. 7 JP5 - Keyboard Power Select .............................................................................. 7 JP6 - On Board AC97 Codec Sound .................................................................... 7 JP7 - On Board LAN (optional) ............................................................................. 7 SW1 - Code to Voltage Definition(optional) .......................................................... 8 Pin Assignment ..................................................................................................... 9 HARDWARE SETUP HARDWARE SETUP ...................................................................................... ...................................................................................... ...................................................................................... 1010101010 HARDWARE SETUP ...................................................................................... HARDWARE SETUP ...................................................................................... HARDWARE SETUP To Install DDR DIMMs ................................................................................................... 10 Installing a New Processor ......................................................................................... 10 To Install a Processor to ZIF Socket ........................................................................... 10 Connect the Processor Fan Connector ...................................................................... 11 Setting the Processor Speed ...................................................................................... 11 BIOS SETUP BIOS SETUP .................................................................................................. .................................................................................................. .................................................................................................. 1111111111 BIOS SETUP .................................................................................................. BIOS SETUP .................................................................................................. BIOS SETUP Starting Setup .............................................................................................................. 11 Main Menu .................................................................................................................... 12 Standard CMOS Features ........................................................................................... 13 Advanced BIOS Features ........................................................................................... 14 Advanced Chipset Features ....................................................................................... 14 Integrated Peripherals ................................................................................................. 14 Power Management Setup .......................................................................................... 14 PNP/PCI Configurations ................................................................................................ 14 PC Health Status .......................................................................................................... 14 Frequency/Voltage Control ......................................................................................... 14 Set Supervisor/User Password .................................................................................. 15 Flash Update Procedure ............................................................................................. 16 APPENDIX APPENDIX .................................................................................................... .................................................................................................... .................................................................................................... 1616161616 APPENDIX .................................................................................................... APPENDIX APPENDIX .................................................................................................... USB 2.0 Driver Installation for Windows 9X ........................................................... 16 Technical Reference Booklet

33333 ARE CONFIGURATIONTIONTIONTIONTION ARE CONFIGURA ARE CONFIGURA HARDHARDHARDHARDHARDWWWWWARE CONFIGURA ARE CONFIGURA Key Key Key Key Key Features Features Features Features : : : : : Features Chipset Chipset Chipset Chipset Chipset • Intel® 845G/GL/GE/PE/GV Chipset. Processor Processor Processor Processor Processor • • • Supports the Intel® Pentium® 4 processors and the Northwood processors in the 478-pin package. Supports PSB (Processor System Bus) frequency of 400MHz (100MHz bus clock). Supports PSB (Processor System Bus) frequency of 533MHz (133MHz bus clock) (only for 845G,845GE,845PE,845GV). VRM 9.0 (V VRM 9.0 (V oltage R oltage R egulator Modules) on Board egulator Modules) on Board oltage Regulator Modules) on Board VRM 9.0 (Voltage R egulator Modules) on Board oltage R VRM 9.0 (V VRM 9.0 (V egulator Modules) on Board • Flexible motherboard design with on board VRM 9.0, easy to upgrade with future Intel® Pentium® 4 and Northwood processors. Cache Cache Cache Cache Cache • The Intel® Pentium® 4 and Northwood processors built-in L2 Cache. System Memory System Memory System Memory System Memory System Memory Supports up to two DDR DIMMs, single-sided or double-sided. Supports DDR200/266 unregistered, 184-pin non-ECC DDR SDRAM DIMMs. • Up to 2.0 Gbytes of 200MHz or 266MHz DDR SDRAM. • • • Does not support double-sided x16 DDR DIMMs. • Up to 2.0 Gbytes of 333MHz DDR SDRAM (only for 845GE/PE/GV). Note: Please ensure that your DIMMs can meet the specification of SPD. AGP Controller (only for 845G/845GE/845PE) AGP Controller (only for 845G/845GE/845PE) AGP Controller (only for 845G/845GE/845PE) AGP Controller (only for 845G/845GE/845PE) AGP Controller (only for 845G/845GE/845PE) • • Supports AGP2.0 including 1x/2x/4x AGP data transfers and 2x/4x Fast Write protocol. AGP 1.5V connector support only, No support for 3.3V or Universal AGP connectors. • High priority access support. • Delayed transaction support for AGP reads that cannot be serviced immediately. On-board I/O On-board I/O On-board I/O On-board I/O On-board I/O • On board two PCI fast IDE ports supporting up to 4 ATA, ATA2 , Ultra ATA33/ 66/100 IDE HDDs, CD-ROMs, ZIP drives and LS-120 drives as boot drive. • One ECP/EPP parallel port. • • One floppy port supports two FDD of 360KB, 720KB, 1.2MB , 1.44MB and Two 16550 Compatible UART serial ports. 2.88MB capacity. PS/2 keyboard connector. PS/2 mouse is supported. • • • One front panel sound connector. • Infrared (IrDA) is supported via a header. Expanded USB Support Expanded USB Support Expanded USB Support Expanded USB Support Expanded USB Support • • Includes 3 UHCI host controllers,increasing the number of external ports to six. Includes 1 EHCI USB2.0 Host Controller that supports all six ports (Bandwidth shared between six ports). Hardware Configuration

44444 On-board VGA(only for 845G/845GE/845GL/845GV) On-board VGA(only for 845G/845GE/845GL/845GV) On-board VGA(only for 845G/845GE/845GL/845GV) On-board VGA(only for 845G/845GE/845GL/845GV) On-board VGA(only for 845G/845GE/845GL/845GV) 3D Setup Render Engine. 3D Graphics Rasterization Enhancements. Full 2D H/W Acceleration. • Core Frequency of 200MHz. • • High Quality Texture Engine. • • • Motion Video Acceleration. • Up to 1600x1200 in 8 bit Color at 85MHz Refresh. • H/W Motion Compensation Assistance for S/W MPEG2 Decode. • • Software DVD at 30fps. Integrated 24-bit 230MHz RAMDAC. System BIOS System BIOS System BIOS System BIOS System BIOS • • • • PnP, APM, ATAPI and Windows 95/98/2000. Full support of ACPI & DMI. Auto detects and supports LBA harddisks with capacities over 8.4GB. Easy to upgrade BIOS by end-user. Plug and Play Plug and Play Plug and Play Plug and Play Plug and Play • • • Supports Plug and Play specification 1.1. Plug and play for DOS, Windows 3.X, Windows 95/98/2000, as well as Windows XP. Fully steerable PCI interrupts. Power Management Power Management Power Management Power Management Power Management Supports SMM, APM and ACPI. Break switch for instant suspend/resume on system operations. Energy star “Green PC” compliant. • • • • Hardware monitoring circuit is supported, provide voltage, fan speed, etc. monitoring (optional). • WOL (Wake-On-Lan) Header support. • • External Modem Ring-in Wake-up support. Supports suspend-to-RAM(STR)(optional). On-board AC97 Sound On-board AC97 Sound On-board AC97 Sound On-board AC97 Sound On-board AC97 Sound Integrated AC97 controller with standard AC97 Codec. Full-Duplex 16-bit record and play back. PnP and APM 1.2 support. • • Direct Sound and Sound Blaster compatible. • • • Win® 95/98/2000/XP, NT drivers ready. • • Line-in, Line-out, Mic-in and MIDI/Game port. Supports ALC650 AC97 Code for six sound channel output (optional). On-board Realtek RTL8100BL PCI LAN (optional) On-board Realtek RTL8100BL PCI LAN (optional) On-board Realtek RTL8100BL PCI LAN (optional) On-board Realtek RTL8100BL PCI LAN (optional) On-board Realtek RTL8100BL PCI LAN (optional) • • • • • Provides 32-bit performance, PCI bus master capability. Full compliance with IEEE 802.3u 100 Base-T specifications and IEEE 802.3X Full Duplex Flow Control. Supports 10 Mb/s and 100 Mb/s operation. Supports Wake-On-LAN function and remote wake-up. Supports ACPI, PCI Power management and PCI VPD. Technical Reference Booklet

55555 Expansion Slots Expansion Slots Expansion Slots Expansion Slots Expansion Slots • • • 1 CNR slot (shares 1 PCI slot) (optional). 1 AGP slot (845GL/GV supports ADD card only, 845G/GE/PE supports ADD card and AGP card)(optional). 6 PCI bus master slots - ver. 2.1 compliant (1 PCI shares with 1 CNR slot). CAUTION Static electricity can harm delicate components of the motherboard. To prevent damage caused by static electricity, discharge the static electricity from your body before you touch any of the computers electronic components. Hardware Configuration

66666 Motherboard Layout Motherboard Layout Motherboard Layout Motherboard Layout Motherboard Layout The following diagrams show the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. # JP1 is only for 845G/GE/PE/GV. # The LAN connector is optional. # AGP Slot (845GL/GV supports ADD card only, 845G/GE/PE supports ADD card and AGP card) (optional). # The Video Out Connector is only for 845G/GL/GE/GV. # The ALC650 embeds an internal analog switch (by driver software) to share LINE input with Surround output, and share MIC input with CENTER/LFE output. NOTE 1) 2) 3) Be sure to check the cable orientation in order to match the colored strip to the pin 1 end of the connector. When you start up the system, please wait for 5 seconds after you power on AC. It is not recommended to add a metal spacer plate on the back of the Socket478. Otherwise, some components will be short and damaged. Technical Reference Booklet

Jumper Settings Jumper Settings Jumper Settings Jumper Settings Jumper Settings This chapter explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. 77777 6 P J JP7 1 2 P J 5 P J S W 1 1 2 3 4 5 6 JP1 CPU Speed Selection CPU Speed Selection CPU Speed Selection CPU Speed Selection CPU Speed Selection In this motherboard, jumperless feature is implemented such that no jumper is required to be set for different type of CPU installed. 1 Notice: 1. Be sure to save the CMOS setting when exit the CMOS. 2. If the CPU is frequency multiplier locked, no CPU speed change will be seen even if the frequency multiplier setting in CMOS setup is changed. JP1 - System Bus Frequency (only for 845G/GE/PE/GV) JP1 - System Bus Frequency (only for 845G/GE/PE/GV) JP1 - System Bus Frequency (only for 845G/GE/PE/GV) JP1 - System Bus Frequency (only for 845G/GE/PE/GV) JP1 - System Bus Frequency (only for 845G/GE/PE/GV) JP1 1 1 1-2* 3-4 4-5 1 JP2 - CMOS Clear JP2 - CMOS Clear JP2 - CMOS Clear JP2 - CMOS Clear JP2 - CMOS Clear CPU Clock Speed Auto* 133MHz 100MHz JP2 1-2* 2-3 Selection Normal* CMOS Clear JP5 JP5 - Keyboard Power Select JP5 - Keyboard Power Select JP5 - Keyboard Power Select JP5 - Keyboard Power Select JP5 - Keyboard Power Select Select Powered by +5V* Powered by +5V Standby 2-3* 1-2 JP6 - On Board AC97 Codec Sound JP6 - On Board AC97 Codec Sound JP6 - On Board AC97 Codec Sound JP6 - On Board AC97 Codec Sound JP6 - On Board AC97 Codec Sound JP6 2-3 1-2* Function AC97 Sound Disable AC97 Sound Enable* JP7 JP7 - On Board LAN (optional) JP7 - On Board LAN (optional) JP7 - On Board LAN (optional) JP7 - On Board LAN (optional) JP7 - On Board LAN (optional) Function On board LAN Enable* On board LAN Disable 1-2* 2-3 Close Open * = Default setting. Hardware Configuration

88888 SW1 - Code to V SW1 - Code to V oltage Definition (optional) oltage Definition (optional) SW1 - Code to Voltage Definition (optional) oltage Definition (optional) SW1 - Code to V SW1 - Code to V oltage Definition (optional) SW1[1:6] VCC_CORE SW1[1:6] VCC_CORE 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 Off 1.100 1.125 1.150 1.175 1.200 1.225 1.250 1.275 1.300 1.325 1.350 1.375 1.400 1.425 1.450 1.475 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1.500 1.525 1.550 1.575 1.600 1.625 1.650 1.675 1.700 1.725 1.750 1.775 1.800 1.825 1.850 Auto* Technical Reference Booklet On Off * =Auto.

分享到：

赞收藏

资料库

昂达主板-P4GE说明书.pdf

相关推荐

主板

热门标签

最新资料