EIKI爱其投影机-EIP-3000N说明书.pdf-资料库

第1页 / 共68页

第2页 / 共68页

第3页 / 共68页

第4页 / 共68页

第5页 / 共68页

第6页 / 共68页

第7页 / 共68页

第8页 / 共68页

EIP-3000N OWNER’S MANUAL EIKI INDUSTRIAL CO., LTD. EIP-3000N_EN_CD__cover 7 06.5.11, 10:18 AM

IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the con- tents of the carton thoroughly against the list of “Supplied accessories” on page 11. Model No.: Serial No.: SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat- ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 and of the same rating as above, which is also indicated on the pin fuse marked face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. or DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi- ately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: WARNING: THIS APPARATUS MUST BE EARTHED. IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green-and-yellow : Earth Blue Brown : Neutral : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: • The wire which is coloured green-and-yellow must be connected to the terminal in the or coloured green or • The wire which is coloured blue must be connected to the terminal which is marked with • The wire which is coloured brown must be connected to the terminal which is marked with plug which is marked by the letter E or by the safety earth symbol green-and-yellow. the letter N or coloured black. the letter L or coloured red. IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN. ii EIP-3000N_EN_CD_a 2 06.5.10, 9:36 AM

EIP-3000N_EN_CD_a 3 06.5.10, 9:36 AM iii

The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian and Portuguese. Carefully read through the operation instructions before operating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch und Portugiesisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch. Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, espagnol, italien et portugais. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur. El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español, italiano y portugués. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector. Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano e portoghese. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore. O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano e Português. Leia cuidadosamente todas as instruções de operação antes de operar o projetor. iv EIP-3000N_EN_CD_a 4 06.5.10, 9:36 AM

Before using the projector, please read this owner’s manual carefully. Introduction ENGLISH 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE. U.S.A. ONLY WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. See bottom of projector. CAUTION RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead sym- bol, within an equilateral triangle, is in- tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment. U.S.A. ONLY INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. U.S.A. ONLY EIP-3000N_EN_CD_b 1 06.5.10, 9:37 AM 1

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification. U.S.A. ONLY WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: The cooling fan in this projector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY-ON button on the projector or the STANDBY button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE. PRODUCT DISPOSAL This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org . Caution Concerning Lamp Replacement See “Replacing the Lamp” on page 55. This EIKI projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. 2 EIP-3000N_EN_CD_b 2 06.5.10, 9:37 AM

How to Read this Owner’s Manual • In this owner’s manual, the illustration and the screen display are simplified for explanation, and may differ slightly from the actual display. Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button RETURN button • Press l RETURN to return to the previous screen when the menu is displayed. Menu Selections (Adjustments) Example: Adjusting “Bright”. • This operation can also be performed by using the buttons on the projector. Press BMENU. • The “Picture” menu screen for the se- lected input mode is displayed. Example: “Picture” screen menu for INPUT 1 (RGB) mode Menu item Press Q or O and select “Picture” to adjust. Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SCR PRJ Net. Help Standard 0 0 0 0 K 1 7 5 0 0 Bright SEL./ADJ. ENTER END 1 2 40 Buttons used in this operation Button used in this step On-screen display Info ........Indicates safeguards for using the projector. Note.........Indicates additional information for setting up and operating the projector. For Future Reference Maintenance P. 52 Troubleshooting PP. 59 and 60 Index P. 63 EIP-3000N_EN_CD_b 3 06.5.10, 9:37 AM 3

Contents Preparing Introduction How to Read this Owner’s Manual ....... 3 Contents ............................................... 4 IMPORTANT SAFEGUARDS ............... 6 How to Access the PDF Owner’s Manuals ............................................ 10 Accessories ........................................ 11 Part Names and Functions ................. 12 Inserting the Batteries .......................... 15 Usable Range ...................................... 15 Quick Start Quick Start .......................................... 16 Using Setup Setting up the Projector ...................... 18 Setting up the Projector ....................... 18 Standard Setup (Front Projection) ....... 18 Ceiling-mount Setup ............................ 18 Projection (PRJ) Mode ......................... 19 Screen Size and Projection Distance .. 20 Connections Connections ........................................ 21 Samples of Cables for Connection ..... 22 Connecting to a Computer ................. 23 Connecting to Video Equipment ......... 24 Connecting to a Monitor with RGB Input Terminal ............................................ 25 Controlling the Projector by a Computer .. 26 Connecting the Power Cord ............... 27 Basic Operation Turning the Projector On/Off .............. 28 Turning the Projector on ....................... 28 Turning the Power off (Putting the Projector into Standby Mode) ........... 29 Image Projection ................................. 30 About the Setup Guide ........................ 30 Adjusting the Projected Image ............ 30 Switching the Input Mode .................... 32 Adjusting the Volume ........................... 32 Displaying the Black Screen and Turning off the Sound Temporarily ................. 32 Correcting Trapezoidal Distortion ........ 33 Resize Mode ......................................... 34 Useful Features Operating with the Remote Control .... 36 Displaying and Setting the Break Timer .... 36 Auto Sync (Auto Sync Adjustment) ..... 36 Freezing a Moving Image .................... 36 Selecting the Picture Mode .................. 36 Menu Items ......................................... 37 Using the Menu Screen ...................... 40 Menu Selections (Adjustments) ........... 40 Picture Adjustment (“Picture” menu) .. 42 Selecting the Picture Mode .................. 42 Adjusting the Image ............................. 43 Adjusting the Color Temperature ......... 43 Progressive ........................................... 43 Lamp Setting ........................................ 43 Adjusting the Projected Image (“SCR - ADJ” menu) ......................... 44 Setting the Resize Mode ...................... 44 Adjusting the Image Position ............... 44 Keystone Correction ............................ 44 Setting the On-screen Display ............. 45 Selecting the Background Image ........ 45 Selecting the Setup Guide ................... 45 Reversing/Inverting Projected Images ... 45 Selecting the On-screen Display Language ... 45 Adjusting the Projector Function (“PRJ - ADJ” menu) .......................... 46 Auto Search Function ........................... 46 Auto Sync (Auto Sync Adjustment) ..... 46 Auto Power Off Function ...................... 46 Setting the Confirmation Sound (System Sound) ................................. 46 Speaker Setting .................................... 46 Selecting the Transmission Speed (RS-232C) ... 47 Fan Mode Setting ................................. 47 Checking the Lamp Life Status ........... 47 System Lock Function .......................... 47 Locking the Operation Buttons on the Projector (Keylock Function) ............. 48 Setting up the Projector Network Environment (“Network” menu) ........ 49 Setting a Password .............................. 49 DHCP Client Setting ............................. 50 TCP/IP Setting ...................................... 50 Confirming the Projector Information ... 50 Troubleshooting with the “Help” menu ...... 51 Utilizing the “Help” menu functions ..... 51 4 EIP-3000N_EN_CD_b 4 06.5.10, 9:37 AM

资料库

EIKI爱其投影机-EIP-3000N说明书.pdf

相关推荐

投影机

热门标签

最新资料