第1页 / 共142页
第2页 / 共142页
第3页 / 共142页
第4页 / 共142页
第5页 / 共142页
第6页 / 共142页
第7页 / 共142页
第8页 / 共142页
Mimaki打印机-CG-75FX说明书.pdf
TABLE OF CONTENTS
Foreword
On This Operation manual
Features
For safe operation
Pictorial signs
Example of pictorial signs
Never Do the Following
Precautions in installation
Precautions in use
Safety labels
How to read this operation manual
Display panel and Indication of the Keys
CHAPTER 1 Before Use
Checking the accessories
Configuration and function
The Front
The Rear
Operation Panel
Carriage
Pinch rollers and grit rollers
Control the clamp pressure
The sheet sensor
Pen line
Scale seal
Connecting the cables
Menu mode
CHAPTER 2 Basic Operations
Operation
Attach a tool
Adjusting the blade tip of the cutter
Attaching a tool
Attaching ball-point pen on the market
Turining the power on
Tool conditions setting
Cut conditions (CT1, CT2, CT3, CT4, CT5) settings
Plotting conditions (PEN) settings
Pouncing conditions (PIN) settings
Half cut conditions (HLF) settings
Loading a sheet of media
Maximum cutting area
Sheet detection
Loading a leaf sheet
Loading a roll sheet
Execute test cutting (plotting)
Starting cutting (plotting)
Setting an origin
Starting cutting (plotting)
Putting the cutting (plotting) on hold
Turning the power off
CHAPTER 3 Function
Functions invoked with the jog mode (jog keys)
Setting an origin
Paper cut
Two-point axis alignment
Cutting area
Digitization operation
Functions invoked with the specific keys
Switch between remote and the local mode [REMOTE]
Set the tool configurations [TOOL]
Set the distance compensation [TOOL]
Feed the paper [FEED]
Clear the data [DATA CLEAR]
Modify the sheet displacement [ENTER / HOLD]
Enter the registration mark detection mode [END]
Functions
Test cutting [SQUARE CUT]
Cut (plot) the same data on multiple sheets [No. COPIES]
Check the sensor for the registration mark detection [MARK sensor]
Correct the light pointer position [MARK SENSOR]
Examine the cut error [SAMPLE CUT]
Output the list of configurations [LIST]
Output the received data by the ASCII code [ASCII DUMP]
Cut a roll sheet at intervals automatically [SHEET CUT]
Switch the displayed language [DISPLAY]
Set each functions [SET UP]
Setting function
Set the operation of the registration mark detection [MARK DETECT]
Warnings on inputting data with registration marks
Method to detect registration marks
Expand the cut (plot) area [EXPANDS]
Switch the cutting mode [CUT MODE]
Set the function according to the blade tip direction [DUMMY CUT]
Specify the sheet type [SHEET SET]
Set the offset value of the automatic feeding function [FEED OFFSET]
Cut off the sheet automatically after completing cutting operation [AUTO. CUT]
Divide a large data before cutting [DIVISION CUT]
Perform cutting with a dotted line [HALF CUT]
Perform plotting with a perforated line [POUNCING]
Switch the origin point [ORGN SELECT]
RotationSwitch the cut (plot) moving direction [ROTATION]
Change the cutting (plotting) order [SORTING]
Switch the commands from a host computer [COMMAND]
Set the configurations with a computer [INTERFACE]
Set the each device number for a USB connection [DEVICE No.]
Command priority setting [PRIORITY]
The maximum size of the response [DISTANCE]
In use of the undetectable sheet [SHEET sensor]
Set the movement speed of carriage and sheet [UP SPEED]
Set the movement distance of carriage and sheet [JOG STEP]
Mute setting on the key noise and the error buzzer [BUZZER]
Switch the unit of length [MM/INCH]
Uncut parts on the corner [ADJ-PRS OFS]
Select the bumber of pinch roller to use [PINCH ROLL.]
Reset the setting values [SETUP RESET]
CHAPTER 4 In Case Of Trouble
Before taking a phenomenon as a trouble
Trouble for which error messages are given on the LCD
Error message
Warning message
CHAPTER 5 Appendix
Specifications of the main unit
Repeatability condition
Cutter blade
Replacing the cutter blade
Adjusting the cutter blade
How to replace the blade for sheet cutter
Sheet setting
Function Flowchart
Functions invoked with the specific keys
Functions invoked with the jog mode (jog keys)
Functions
CUTTING PLOTTER
CG-FX Series
OPERATION MANUAL
MIMAKI ENGINEERING CO., LTD.
TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan
Phone: +81-3-5420-8671 Fax: +81-3-5420-8687
URL: http: // www.mimaki. co. jp/
D200805
CAUTION
DISCLAIMER OF WARRANTY: THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE
SOLE AND EXCLUSIVE WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR AUTHO-
RIZES DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE
ANY OTHER WARRANTY OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH
ANY PRODUCT WITHOUT MIMAKI'S PRIOR WRITTEN CONSENT. IN NO EVENT SHALL
MIMAKI BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT.
Requests
• This Operation manual has been carefully prepared for your easy understanding, however, please
do not hesitate to contact a distributor in your district or our office if you have any inquiry.
• Description contained in this Operation manual are subject to change without notice for improve-
ment.
• Generally, names and designations referred to in this Operation manual are trade marks or regis-
tered trade marks of the manufacturers or suppliers.
Reproduction of this manual is strictly prohibited.
All Rights Reserved. Copyright © 2007 MIMAKI ENGINEERING Co., Ltd.
– i –
Not for use in a computer room as defined in the Standard for Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75 National Devision.
FCC Statement (USA)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the Operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which cause
the user will be required to correct the interference at his own expense.
•
In the case where MIMAKI-recommended cable is not used for connection of
this device, limits provided by FCC rules can be exceeded.
To prevent this, use of MIMAKI-recommended cable is essential for the
connection of this device.
Interference to televisions and radios
The product described in this manual generates high frequency when operating.
The product can interfere with radios and televisions if set up or commissioned under improper
conditions. The product is not guaranteed against any damage to specific-purpose radio and
televisions.
The product’s interference with your radio or television will be checked by turning on/off the
power switch of the product.
In the event that the product is the cause of interference, try to eliminate it by taking one of the
following corrective measures or taking some of them in combination.
• Change the orientation of the antenna of the television set or radio to find a position without
reception difficulty.
• Separate the television set or radio from this product.
• Plug the power cord of this product into an outlet which is isolated from power circuits connected
to the television set or radio.
– ii –
Foreword
Congratulations on your purchase of a CG-FX series cutting plotter.
CG-FX series cutting plotter is a highly functional cutting plotter with the high-speed registration
mark detection.
Read this Operation manual carefully and make the most effective use of your plotter.
Be sure to read this Operation manual carefully, before starting to operate the plotter.
This Operation manual to the models as firmware version 2.50 or later.
When turning on the power, you can confirm the firmware version. To confirm the firmware version
refer to "Turning the power on" (Refer to Page 2.7)
On This Operation manual
• This Operation manual describes the operation and maintenance of CG-FX series cutting
plotter (hereinafter referred to as the device).
• Please read and fully understand this Operation manual before putting the machine into
service. It is also necessary to keep this Operation manual on hand.
• Make arrangements to deliver this Operation manual to the person in charge of the op-
eration of this device.
• This Operation manual has been carefully prepared for your easy understanding, how-
ever, please do not hesitate to contact a distributor in your district or our office if you have
any inquiry.
• Description contained in this Operation manual are subject to change without notice for
improvement.
•
In the case where this Operation manual should be illegible due to destruction or lost by
fire or breakage, purchase another copy of the Operation manual from our office.
– iii –
Features
The features of the device are described below. Together with the method of operation of the device
explained in this manual, they help you understand how to use the device properly.
Photo electric eye
High accuracy mark-detection sensor enables the mark plotted on sheets to automatically read, com-
pensate distances, set the plotting and compensate paper gradient.
Roll Sheet Stopper Function
The newly developed roll stopper is incorporated so as to set a wide roll paper without sagging.
Two Clamp Pressure Modes Change Over Mechanism
The sheet clamp system has been modified to incorporate two clamp pressure modes change over
mechanism so as to widen the applicable sheet size limit.
Strong pressure mode substantially increases the clamp pressure that prevents a long sheet slippage.
The moderate pressure mode prevents from getting scratching by grit roller during plot operation.
New Cutter Holder
The new cutter holder equipping with a capped tip has a mechanism enabling the tip protrusion to
adjust by the rotable knob with attaching to the pen carriage. (Former type cutter holders are also
usable.)
Front Loading Capability
By installing the roll table at the front side, the roll sheet can be cut by arranging the front loading.
(Unsuitable in use of the automatic sheet cutting function.)
Roll sheet settable up to 6 rolls
Up to 6 roll tables attachable to leg assy.
Plug-in cutting software (FineCut) attached
The plug-in software, FineCut enables to perform finely cutting characters or illustration edited on the
Illustrator.
Automatic Sheet Cutting Function
Enables to cut a roll sheet or a leaf sheet automatically
– iv –
For safe operation
Pictorial signs
Pictorial signs are used in this Operation manual for safe operation of and in prevention of damages to
the device. Pictorial signs and their meanings are given below. Read and fully understand before
reading the text.
•
Indicates the case where it is assumed that misuse of the machine, ignor-
ing this sign, as this may cause fire or poisoning. Be sure to read this
manual for proper operation.
•
Indicates the case where it is assumed that misuse of the machine, ignor-
ing this sign, can cause damage only to property.
•
Indicates a caution you must observe when operating the product.
• The symbol "
" indicates helpful information that will facilitate the use of
the device.
•
Indicates the reference page for related contents.
Example of pictorial signs
• The symbol "
" indicates the case where some phenomenon that requires
a CAUTION sign (including "DANGER" and "WARNING" signs) exists. A
concrete precaution (precaution against an electric shock in the case of the
sketch given on the left) is shown in the illustration.
• The symbol "
" indicates a prohibited behavior. A concrete illustration of
prohibition (disassembly is prohibited in the sketch given on the left) is
shown in or next to the illustration.
• The symbol "
" indicates a thing that is forced to be done and instruction
that is forced to be followed. A concrete illustration of instruction (the
removal of a plug from the receptacle is instructed in the sketch given on
the left) is drawn in the illustration.
– v –
Never Do the Following
WARNING
Do not disassemble or remodel the device.
Abnormal event occurs.
• Never disassemble or remodel
•
If the device is used under an
the main unit of the plotter.
abnormal condition where the
Disassembling/remodeling any of
device produces smoke or
them will result in electric shocks
unpleasant smell, fire or electric
or breakdown of the device.
shocks can result. Be sure to
Do not use the device in damp places.
• Avoid damp environments when
putting the device into service.
Do not splash water onto the
device.
High-humidity or water will give
rise to fire, electric shocks or
breakdown of the device.
turn off the power switch
immediately and detach the plug
from the receptacle. Check first
to be sure that the device no
longer produces smoke, and
contact a distributor in your
district for repair. Never repair
your device by yourself since it is
very dangerous for you to do so.
Handling of the power cable
• Use the supplied power cable.
•
Take care not to damage, break
or work on the power cable.
If a heavy matter is placed on the
power cable, heated or drawn,
the power cable can break to
cause fire or electric shocks.
– vi –
相关推荐
2023年江西萍乡中考道德与法治真题及答案.doc
2012年重庆南川中考生物真题及答案.doc
2013年江西师范大学地理学综合及文艺理论基础考研真题.doc
2020年四川甘孜小升初语文真题及答案I卷.doc
2020年注册岩土工程师专业基础考试真题及答案.doc
2023-2024学年福建省厦门市九年级上学期数学月考试题及答案.doc
2021-2022学年辽宁省沈阳市大东区九年级上学期语文期末试题及答案.doc
2022-2023学年北京东城区初三第一学期物理期末试卷及答案.doc
2018上半年江西教师资格初中地理学科知识与教学能力真题及答案.doc
2012年河北国家公务员申论考试真题及答案-省级.doc
2020-2021学年江苏省扬州市江都区邵樊片九年级上学期数学第一次质量检测试题及答案.doc
2022下半年黑龙江教师资格证中学综合素质真题及答案.doc
