Milestone Semiconductor Inc.
GENERAL DESCRIPTION
MST9611 is an Over-Voltage-Protection
(OVP) and Over-Current-Protection (OCP)
device. It can disconnect IN to OUT to
protect load in case wrong input operating
conditions are detected. The system is
positive overvoltage protected up to 36V.
The internal overvoltage thresholds (OVLO)
is 6.1V and internal overcurrent thresholds
(OCP)
MST9611 also has
internal over
temperature protect(OTP)
function and it can monitor chip temperature
to protect the device.
The device is packaged in advanced
is 2.7A.
Over Voltage and Over Current Protection IC
FEATURES
Typical RON: 100mΩ NMOS @5V/1A
Maximum Output Current: 2.5A.
VIN Operating Range: 2.5V to 36V
Internal Overvoltage Lockout : 6.1V
Internal Overcurrent Lockout : 2.7A(MIN)
Overvoltage-Protection Response Time:
<500ns
Startup Debounce Time: 16ms(TYP).
Typical Output Power on Time:
16.5ms(TYP).
Internal Thermal-Shutdown Protection
ESD Protected: Human Body Model :
JESD22-A114(All pins)±2KV
APPLICATION
GPS and Navigation Equipment
Portable Media Devices, Laptop & MID
SLR Digital Cameras
Industrial Handheld
Equipment
and Enterprise
full-Green Packaging (DFN4).
Page1-7 Rev.1.1 Mar-06-2018
Milestone Semiconductor Inc.
PIN ASSIGNMENT
Over Voltage and Over Current Protection IC
PIN
1
2、3
4
NAME
IN
GND
OUT
DISCRIPTION
Input Voltage.
Ground. Connect GND pins together for proper operation.
Load Output.
BLOCK DIAGRAM
FUNCTIONAL DESCRIPTION
feature a
The OVP switch with overvoltage protection
low 100mΩ (typical)
on-resistance(RON) internal FET and protect low-voltage systems against voltage faults up
to 36VDC. The internal overvoltage thresholds (OVLO) is 6.1V and internal overcurrent
thresholds (OCP) is 2.7A.
The internal FET turns off when the junction temperature exceeds +155ºC (TYP.). The device
exits thermal shutdown after the junction temperature cools by 20ºC (TYP.).
Page2-7 Rev.1.1 Mar-06-2018
Milestone Semiconductor Inc.
Input Capacitor
Over Voltage and Over Current Protection IC
To limit the voltage drop on the input supply caused by transient inrush current when
the switch turns on into a discharged load capacitor or short-circuit, a capacitor 1μF or lager
must be placed between the VIN and GND pins.
Output Capacitor
A 1μF or lager capacitor should be placed between the OUT and GND pins.
ABSOLUTE MAXIMUM RATINGS
Stresses exceeding the absolute maximum ratings may damage the device. The device may
not function or be operable above the recommended operating conditions and stressing the parts
to these levels is not recommended. In addition, extended exposure to stresses above the
recommended operating conditions may affect device reliability. The absolute maximum ratings
are stress ratings only.
SYMBOL
VIN
VOUT
ISW1
ISW2
PD
TSTG
TA
TStore
TJ
PARAMETERS
VIN to GND
VOUT to GND
MIN
-0.3
-0.3
Maximum Continuous Current of switch IN-OUT
Maximum Peak Current of switch IN-OUT(10ms)
Power Dissipation at TA= +70℃
Storage Junction Temperature
Operating Temperature Range
Soldering Temperature (reflow).
Junction Temperature
-65
-40
MAX
36
28
2.7
4
1.0
+150
+85
+260
+150
UNIT
V
V
A
A
W
℃
℃
℃
℃
Page3-7 Rev.1.1 Mar-06-2018
Milestone Semiconductor Inc.
ELECTRICAL CHARACTERISTICS
Over Voltage and Over Current Protection IC
Unless otherwise noted, typical values are at VIN=5V and TA=25℃.
SYMBOL
PARAMETERS
CONDITIONS
MIN
TYP
MAX
UNIT
Basic Operation
Input Voltage
VIN Quiescent Current VIN=5V, OUT floating
2.5
110
100
4.0
36
VIN=5.0V, IOUT=1A
VIN rise up
5.9
6.1
6.3
V
μA
mΩ
KΩ
V
V
V
ms
ms
ms
VIN
IIN
RON
Rdischarge
VOVLO
VUVLO_R
Input Over
On-Resistance of
Switch IN-OUT
Output discharge
resistance
Overvoltage protect
of VIN
Overvoltage protect
hysteresis of VIN
Under Voltage
Lockout Threshold
tDEB
Debounce Time
tON
Switch Turn-On Time
Output power-on
Time
tON_ALL
tOFF_RES(1)
VIN Rising
Time from 2.1V VOVLO to VOUT
stop rising
150
300
ns
Dynamic Characteristics: see figure
Overcurrent protect of
IOCP
I
2.7
3.3
A
Page4-7 Rev.1.1 Mar-06-2018
Milestone Semiconductor Inc.
ISHORT
TOCP
OCP debounce time
TREC_OCP OCP recovery time
Over Temperature Protection(OTP)
Thermal Shutdown
Thermal-shutdown Hysteresis
Over Voltage and Over Current Protection IC
180
30
1
155
20
mA
ms
s
℃
℃
Note:
1、 Guaranteed by characterization and design.
APPLICATION CIRCUITS
Note1: Reference input and output capacitance value is 1uF.
*:This electric circuit only supplies for reference.
Page5-7 Rev.1.1 Mar-06-2018
Milestone Semiconductor Inc.
TYPICAL CHARACTERISTICS
Over Voltage and Over Current Protection IC
Input Quiescent Current vs.Temperature OVP threshold vs. Temperature
On Resistance vs. Temperature Input Quiescent Current vs. Input Voltage
Power ON Debounce Time Switch Turn-on Time
Page6-7 Rev.1.1 Mar-06-2018
Milestone Semiconductor Inc.
Over Voltage and Over Current Protection IC
OVP Turn-off Response Time OCP Recovery
PACKAGE DIMENSION
Page7-7 Rev.1.1 Mar-06-2018