第1页 / 共6333页
第2页 / 共6333页
第3页 / 共6333页
第4页 / 共6333页
第5页 / 共6333页
第6页 / 共6333页
第7页 / 共6333页
第8页 / 共6333页
3GPP TS 36 521-1 V15.5.0 (2019-07).pdf
Intellectual Property Rights
Legal Notice
Modal verbs terminology
Foreword
Introduction
1 Scope
2 References
3 Definitions, symbols and abbreviations
3.1 Definitions
3.2 Symbols
3.3 Abbreviations
4 General
4.1 Categorization of test requirements in CA, UL-MIMO, ProSe, Dual Connectivity, UE category 0, UE category M1, UE category M2
4.2 RF requirements in later releases
5 Frequency bands and channel arrangement
5.1 General
5.2 Operating bands
5.2A Operating bands for CA
5.2B Operating bands for UL-MIMO
5.2C Operating bands for Dual Connectivity
5.2D Operating bands for ProSe
5.2E Operating bands for UE category 0, UE category M1, M2 and UE category 1bis
5.2F Operating bands for UE category NB1 and NB2
5.2G Operating bands for V2X Communication
5.3 TXŒRX frequency separation
5.3A TXŒRX frequency separation for CA
5.3F TXŒRX frequency separation for category NB1 and NB2
5.4 Channel arrangement
5.4.1 Channel spacing
5.4.1A Channel spacing for CA
5.4.1F Channel spacing for UE category NB1 and NB2
5.4.2 Channel bandwidth
5.4.2.1 Channel bandwidths per operating band
5.4.2A Channel bandwidth for CA
5.4.2A.1 Channel bandwidths per operating band for CA
5.4.2B Channel bandwidth for UL-MIMO
5.4.2B.1 Channel bandwidths per operating band for UL- MIMO
5.4.2C Channel bandwidth for Dual Connectivity
5.4.2D Channel bandwidth for ProSe
5.4.2D.1 Channel bandwidths per operating band for ProSe
5.4.2F Channel bandwidth for category NB1 and category NB2
5.4.2G Channel bandwidth for V2X Communication
5.4.2G.1 Channel bandwidths per operating band for V2X Communication
5.4.3 Channel raster
5.4.3A Channel raster for CA
5.4.3F Channel raster for UE category NB1 and NB2
5.4.4 Carrier frequency and EARFCN
5.4.4F Carrier frequency and EARFCN for category NB1 and NB2
6 Transmitter Characteristics
6.1 General
6.2 Transmit power
6.2.1 Void
6.2.2 UE Maximum Output Power
6.2.2.1 Test purpose
6.2.2.2 Test applicability
6.2.2.3 Minimum conformance requirements
6.2.2.4 Test description
6.2.2.4.1 Initial condition
6.2.2.4.2 Test procedure
6.2.2.4.3 Message contents
6.2.2.5 Test requirements
6.2.2_1 Maximum Output Power for HPUE
6.2.2_1.1 Test purpose
6.2.2_1.2 Test applicability
6.2.2_1.3 Minimum conformance requirements
6.2.2_1.4 Test description
6.2.2_1.5 Test requirements
6.2.2A UE Maximum Output Power for CA
6.2.2A.0 Minimum conformance requirements
6.2.2A.1 UE Maximum Output Power for CA (intra-band contiguous DL CA and UL CA)
6.2.2A.1.1 Test purpose
6.2.2A.1.2 Test applicability
6.2.2A.1.3 Minimum conformance requirements
6.2.2A.1.4 Test description
6.2.2A.1.5 Test Requirements
6.2.2A.1_3 UE Maximum Output Power for CA and HPUE (intra-band contiguous DL CA and UL CA)
6.2.2A.1_3.1 Test purpose
6.2.2A.1_3.2 Test applicability
6.2.2A.1_3.3 Minimum conformance requirements
6.2.2A.1_3.4 Test description
6.2.2A.1_3.5 Test Requirements
6.2.2A.2 UE Maximum Output Power for CA (inter-band DL CA and UL CA)
6.2.2A.2.1 Test purpose
6.2.2A.2.2 Test applicability
6.2.2A.2.3 Minimum conformance requirements
6.2.2A.2.4 Test description
6.2.2A.2.5 Test Requirements
6.2.2A.3 UE Maximum Output Power for CA (intra-band non-contiguous DL CA and UL CA)
6.2.2A.4 UE Maximum Output Power for CA (3UL CA)
6.2.2A.4.1 Test purpose
6.2.2A.4.2 Test applicability
6.2.2A.4.3 Minimum conformance requirements
6.2.2A.4.4 Test description
6.2.2A.4.5 Test Requirements
6.2.2A.4.1 Void
6.2.2A.4.2 Void
6.2.2B UE Maximum Output Power for UL-MIMO
6.2.2B.1 Test purpose
6.2.2B.2 Test applicability
6.2.2B.3 Minimum conformance requirements
6.2.2B.4 Test description
6.2.2B.4.1 Initial condition
6.2.2B.4.2 Test procedure
6.2.2B.4.3 Message contents
6.2.2B.5 Test requirements
6.2.2B_1 HPUE Maximum Output Power for UL-MIMO
6.2.2B_1.1 Test purpose
6.2.2B_1.2 Test applicability
6.2.2B_1.3 Minimum conformance requirements
6.2.2B_1.4 Test description
6.2.2B_1.5 Test requirements
6.2.2C
6.2.2D UE Maximum Output Power for ProSe
6.2.2D.0 Minimum conformance requirements
6.2.2D.1 UE Maximum Output Power for ProSe Discovery
6.2.2D.1.1 Test purpose
6.2.2D.1.2 Test applicability
6.2.2D.1.3 Minimum Conformance requirements
6.2.2D.1.4 Test description
6.2.2D.1.5 Test requirements
6.2.2D.2 UE Maximum Output Power for ProSe Direct Communication
6.2.2D.2.1 Test purpose
6.2.2D.2.2 Test applicability
6.2.2D.2.3 Minimum conformance requirements
6.2.2D.2.4 Test description
6.2.2E UE Maximum Output Power for UE category 0
6.2.2E.1 Test purpose
6.2.2E.2 Test applicability
6.2.2E.3 Minimum conformance requirements
6.2.2E.4 Test description
6.2.2E.4.3 Message contents
6.2.2E.5 Test requirements
6.2.2EA UE Maximum Output Power for UE category M1
6.2.2EA.1 Test purpose
6.2.2EA.2 Test applicability
6.2.2EA.3 Minimum conformance requirements
6.2.2EA.4 Test description
6.2.2EA.4.3 Message contents
6.2.2EA.5 Test requirements
6.2.2EB UE Maximum Output Power for UE category 1bis
6.2.2EB.1 Test purpose
6.2.2EB.2 Test applicability
6.2.2EB.3 Minimum conformance requirements
6.2.2EB.4 Test description
6.2.2EB.4.1 Initial conditions
6.2.2EB.4.2 Test procedure
6.2.2EB.4.3 Message contents
6.2.2EB.5 Test requirement
6.2.2EC UE Maximum Output Power for UE category M2
6.2.2EC.1 Test purpose
6.2.2EC.2 Test applicability
6.2.2EC.3 Minimum conformance requirements
6.2.2EC.4 Test description
6.2.2EC.4.1 Initial condition
6.2.2EC.4.2 Test procedure
6.2.2EC.4.3 Message contents
6.2.2EC.5 Test requirements
6.2.2F UE Maximum Output Power for category NB1 and NB2
6.2.2F.1 Test purpose
6.2.2F.2 Test applicability
6.2.2F.3 Minimum conformance requirements
6.2.2F.4 Test description
6.2.2F.4.1 Initial condition
6.2.2F.4.2 Test procedure
6.2.2F.4.3 Message contents
6.2.2F.5 Test requirements
6.2.2FA UE Maximum Output Power for category NB1 and NB2/Power Class 6
6.2.2FA.1 Test purpose
6.2.2FA.2 Test applicability
6.2.2FA.3 Minimum conformance requirements
6.2.2FA.4 Test description
6.2.2FA.5 Test requirements
6.2.2G UE Maximum Output Power for V2X Communication
6.2.2G.1 UE Maximum Output Power for V2X Communication / Non-concurrent with E-UTRA uplink transmission
6.2.2G.1.1 Test purpose
6.2.2G.1.2 Test applicability
6.2.2G.1.3 Minimum conformance requirements
6.2.2G.1.4 Test description
6.2.2G.1.4.1 Initial conditions
6.2.2G.1.4.2 Test procedure
6.2.2G.1.4.3 Message contents
6.2.2G.1.5 Test requirements
6.2.2G.2 UE Maximum Output Power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmission
6.2.2G.2.1 Test purpose
6.2.2G.2.2 Test applicability
6.2.2G.2.3 Minimum conformance requirements
6.2.2G.2.4 Test description
6.2.2G.2.4.1 Initial conditions
6.2.2G.2.4.2 Test procedure
6.2.2G.2.4.3 Message contents
6.2.2G.2.5 Test requirements
6.2.2G.3 UE Maximum Output Power for V2X Communication / Intra-band contiguous multi-carrier operation
6.2.2G.3.1 Test purpose
6.2.2G.3.2 Test applicability
6.2.2G.3.3 Minimum conformance requirements
6.2.2G.3.4 Test description
6.2.2G.3.4.1 Initial conditions
6.2.2G.3.4.2 Test procedure
6.2.2G.3.4.3 Message contents
6.2.2G.3.5 Test requirements
6.2.2G.4 UE Maximum Output Power for V2X Communication / Power class 2
6.2.2G.4.1 UE Maximum Output Power for V2X Communication / Power class 2 / Non-concurrent with E-UTRA uplink transmissions
6.2.2G.4.1.1 Test purpose
6.2.2G.4.1.2 Test applicability
6.2.2G.4.1.3 Minimum conformance requirements
6.2.2G.4.1.4 Test description
6.2.2G.4.1.4.1 Initial conditions
6.2.2G.4.1.4.2 Test procedure
6.2.2G.4.1.4.3 Message contents
6.2.2G.4.1.5 Test requirements
6.2.3 Maximum Power Reduction (MPR)
6.2.3.1 Test purpose
6.2.3.2 Test applicability
6.2.3.3 Minimum conformance requirements
6.2.3.4 Test description
6.2.3.4.1 Initial condition
6.2.3.4.2 Test procedure
6.2.3.4.3 Message contents
6.2.3.5 Test requirements
6.2.3_1 Maximum Power Reduction (MPR) for HPUE
6.2.3_1.1 Test purpose
6.2.3_1.2 Test applicability
6.2.3_1.3 Minimum conformance requirements
6.2.3_1.4 Test description
6.2.3_1.5 Test requirements
6.2.3_2 Maximum Power Reduction (MPR) for Multi-Cluster PUSCH
6.2.3_2.1 Test purpose
6.2.3_2.2 Test applicability
6.2.3_2.3 Minimum conformance requirements
6.2.3_2.4 Test description
6.2.3_2.4.1 Initial condition
6.2.3_2.4.2 Test procedure
6.2.3_2.4.3 Message contents
6.2.3_2.5 Test requirements
6.2.3_3 Maximum Power Reduction (MPR) for UL 64QAM
6.2.3_3.1 Test purpose
6.2.3_3.2 Test applicability
6.2.3_3.3 Minimum conformance requirements
6.2.3_3.4 Test description
6.2.3_3.4.1 Initial condition
6.2.3_3.4.2 Test procedure
6.2.3_3.4.3 Message contents
6.2.3_3.5 Test requirements
6.2.3_4 Maximum Power Reduction (MPR) for Multi-Cluster PUSCH with UL 64QAM
6.2.3_4.1 Test purpose
6.2.3_4.2 Test applicability
6.2.3_4.3 Minimum conformance requirements
6.2.3_4.4 Test description
6.2.3_4.4.1 Initial condition
6.2.3_4.4.2 Test procedure
6.2.3_4.4.3 Message contents
6.2.3_4.5 Test requirements
6.2.3_5 Maximum Power Reduction (MPR) for UL 256QAM
6.2.3_5.1 Test purpose
6.2.3_5.2 Test applicability
6.2.3_5.3 Minimum conformance requirements
6.2.3_5.4 Test description
6.2.3_5.4.1 Initial condition
6.2.3_5.4.2 Test procedure
6.2.3_5.4.3 Message contents
6.2.3_5.5 Test requirements
6.2.3_6 Maximum Power Reduction (MPR) for Multi-Cluster PUSCH with UL 256QAM
6.2.3_6.1 Test purpose
6.2.3_6.2 Test applicability
6.2.3_6.3 Minimum conformance requirements
6.2.3_6.4 Test description
6.2.3_6.4.1 Initial condition
6.2.3_6.4.2 Test procedure
6.2.3_6.4.3 Message contents
6.2.3_6.5 Test requirements
6.2.3A Maximum Power Reduction (MPR) for CA
6.2.3A.1 Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA)
6.2.3A.1.1 Test purpose
6.2.3A.1.2 Test applicability
6.2.3A.1.3 Minimum conformance requirements
6.2.3A.1.4 Test description
6.2.3A.1.5 Test Requirements
6.2.3A.1_1 Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM
6.2.3A.1_1.1 Test purpose
6.2.3A.1_1.2 Test applicability
6.2.3A.1_1.3 Minimum conformance requirements
6.2.3A.1_1.4 Test description
6.2.3A.1_1.5 Test requirement
6.2.3A.1_2 Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM
6.2.3A.1_2.1 Test purpose
6.2.3A.1_2.2 Test applicability
6.2.3A.1_2.3 Minimum conformance requirements
6.2.3A.1_2.4 Test description
6.2.3A.1_2.5 Test requirement
6.2.3A.1_3 Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for HPUE
6.2.3A.1_3.1 Test purpose
6.2.3A.1_3.2 Test applicability
6.2.3A.1_3.3 Minimum conformance requirements
6.2.3A.1_3.4 Test description
6.2.3A.1_3.5 Test Requirements
6.2.3A.2 Maximum Power Reduction (MPR) for CA (inter-band DL CA and UL CA)
6.2.3A.2.1 Test purpose
6.2.3A.2.2 Test applicability
6.2.3A.2.3 Minimum conformance requirements
6.2.3A.2.4 Test description
6.2.3A.2.5 Test Requirements
6.2.3A.2_1 Maximum Power Reduction (MPR) for CA (inter-band DL CA and UL CA) for UL 64QAM
6.2.3A.2_1.1 Test purpose
6.2.3A.2_1.2 Test applicability
6.2.3A.2_1.3 Minimum conformance requirements
6.2.3A.2_1.4 Test description
6.2.3A.2_1.5 Test Requirements
6.2.3A.2_2 Maximum Power Reduction (MPR) for CA (inter-band DL CA and UL CA) for UL 256QAM
6.2.3A.2_2.1 Test purpose
6.2.3A.2_2.2 Test applicability
6.2.3A.2_2.3 Minimum conformance requirements
6.2.3A.2_2.4 Test description
6.2.3A.2_2.5 Test Requirement
6.2.3A.3 Maximum Power Reduction (MPR) for CA (intra-band non-contiguous DL CA and UL CA)
6.2.3A.3.1 Test purpose
6.2.3A.3.2 Test applicability
6.2.3A.3.3 Minimum conformance requirements
6.2.3A.3.4 Test description
6.2.3A.3.5 Test Requirements
6.2.3A.3_1 Maximum Power Reduction (MPR) for CA (intra-band non-contiguous DL CA and UL CA) for UL 64QAM
6.2.3A.3_1.1 Test purpose
6.2.3A.3_1.2 Test applicability
6.2.3A.3_1.3 Minimum conformance requirements
6.2.3A.3_1.4 Test description
6.2.3A.3_1.5 Test Requirements
6.2.3A.3_2 Maximum Power Reduction (MPR) for CA (intra-band non-contiguous DL CA and UL CA) for UL 256QAM
6.2.3A.3_2.1 Test purpose
6.2.3A.3_2.2 Test applicability
6.2.3A.3_2.3 Minimum conformance requirements
6.2.3A.3_2.4 Test description
6.2.3A.3_2.5 Test Requirements
6.2.3A.4 Maximum Power Reduction (MPR) for CA (3UL CA)
6.2.3A.4.1 Test purpose
6.2.3A.4.2 Test applicability
6.2.3A.4.3 Minimum conformance requirements
6.2.3A.4.4 Test description
6.2.3A.4.4.1 Initial conditions
6.2.3A.4.5 Test Requirements
6.2.3B Maximum Power Reduction (MPR) for UL-MIMO
6.2.3B.1 Test purpose
6.2.3B.2 Test applicability
6.2.3B.3 Minimum conformance requirements
6.2.3B.4 Test description
6.2.3B.4.1 Initial condition
6.2.3B.4.2 Test procedure
6.2.3B.4.3 Message contents
6.2.3B.5 Test requirements
6.2.3D UE Maximum Output Power for ProSe
6.2.3D.0 Minimum conformance requirements
6.2.3D.1 Maximum Power Reduction (MPR) for ProSe Discovery
6.2.3D.1.1 Test purpose
6.2.3D.1.2 Test applicability
6.2.3D.1.3 Minimum conformance requirements
6.2.3D.1.4 Test description
6.2.3D.1.4.1 Initial condition
6.2.3D.1.4.2 Test procedure
6.2.3D.1.4.3 Message contents
6.2.3D.1.5 Test requirements
6.2.3D.2 Maximum Power Reduction (MPR) ProSe Direct Communication
6.2.3D.2.1 Test purpose
6.2.3D.2.2 Test applicability
6.2.3D.2.3 Minimum conformance requirements
6.2.3D.2.4 Test description
6.2.3D.2.4.1 Initial conditions
6.2.3D.2.4.2 Test procedure
6.2.3D.2.4.3 Message contents
6.2.3D.2.5 Test requirements
6.2.3E Maximum Power Reduction (MPR) for UE category 0
6.2.3E.1 Test purpose
6.2.3E.2 Test applicability
6.2.3E.3 Minimum conformance requirements
6.2.3E.4 Test description
6.2.3E.4.1 Initial condition
6.2.3E.4.2 Test procedure
6.2.3E.4.3 Message contents
6.2.3E.5 Test requirements
6.2.3EA Maximum Power Reduction (MPR) for UE category M1
6.2.3EA.1 Test purpose
6.2.3EA.2 Test applicability
6.2.3EA.3 Minimum conformance requirements
6.2.3EA.4 Test description
6.2.3EA.4.1 Initial condition
6.2.3EA.4.2 Test procedure
6.2.3EA.4.3 Message contents
6.2.3EA.5 Test requirements
6.2.3EB Maximum Power Reduction (MPR) for UE category 1bis
6.2.3EB.1 Test purpose
6.2.3EB.2 Test applicability
6.2.3EB.3 Minimum conformance requirements
6.2.3EB.4 Test description
6.2.3EB.4.1 Initial conditions
6.2.3EB.4.2 Test procedure
6.2.3EB.4.3 Message contents
6.2.3EB.5 Test requirement
6.2.3EC Maximum Power Reduction (MPR) for UE category M2
6.2.3EC.1 Test purpose
6.2.3EC.2 Test applicability
6.2.3EC.3 Minimum conformance requirements
6.2.3EC.4 Test description
6.2.3EC.4.1 Initial condition
6.2.3EC.4.2 Test procedure
6.2.3EC.4.3 Message contents
6.2.3EC.5 Test requirements
6.2.3F Maximum Power Reduction (MPR) for category NB1 and NB2
6.2.3F.1 Test purpose
6.2.3F.2 Test applicability
6.2.3F.3 Minimum conformance requirements
6.2.3F.4 Test description
6.2.3F.4.1 Initial condition
6.2.3F.4.2 Test procedure
6.2.3F.4.3 Message contents
6.2.3F.5 Test requirements
6.2.3FA Maximum Power Reduction (MPR) for category NB1 and NB2/Power Class 6
6.2.3FA.1 Test purpose
6.2.3FA.2 Test applicability
6.2.3FA.3 Minimum conformance requirements
6.2.3FA.4 Test description
6.2.3FA.5 Test requirements
6.2.3G Maximum Power Reduction (MPR) for V2X communication
6.2.3G.1 Maximum Power Reduction (MPR) for V2X Communication / Power class 3
6.2.3G.1.1 Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Contiguous allocation of PSCCH and PSSCH / Non
6.2.3G.1.2 Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Non-contiguous allocation of PSCCH and PSSCH /
6.2.3G.1.2.1 Test purpose
6.2.3G.1.2.2 Test applicability
6.2.3G.1.2.3 Minimum conformance requirements
6.2.3G.1.2.4 Test description
6.2.3G.1.2.4.1 Initial conditions
6.2.3G.1.2.4.2 Test procedure
6.2.3G.1.2.4.3 Message contents
6.2.3G.1.2.5 Test requirement
6.2.3G.1.3 Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Simultaneous E-UTRA V2X sidelink and E-UTRA up
6.2.3G.1.3.1 Test purpose
6.2.3G.1.3.2 Test applicability
6.2.3G.1.3.3 Minimum conformance requirements
6.2.3G.1.3.4 Test description
6.2.3G.1.3.4.1 Initial conditions
6.2.3G.1.3.4.2 Test procedure
6.2.3G.1.3.4.3 Message contents
6.2.3G.1.3.5 Test requirements
6.2.3G.1.4 Maximum Power Reduction (MPR) for V2X Communication / Power class 3 / Intra-band contiguous multi-carrier operation
6.2.3G.1.4.1 Test purpose
6.2.3G.1.4.2 Test applicability
6.2.3G.1.4.3 Minimum conformance requirements
6.2.3G.1.4.4 Test description
6.2.3G.1.4.4.1 Initial conditions
6.2.3G.1.4.4.2 Test procedure
6.2.3G.1.4.4.3 Message contents
6.2.3G.1.4.5 Test requirement
6.2.3G.2 Maximum Power Reduction (MPR) for V2X Communication / Power class 2
6.2.3G.2.1 Maximum Power Reduction (MPR) for V2X Communication / Power class 2 / Contiguous allocation of PSCCH and PSSCH / Non
6.2.3G.2.1.1 Test purpose
6.2.3G.2.1.2 Test applicability
6.2.3G.2.1.3 Minimum conformance requirements
6.2.3G.2.1.4 Test description
6.2.3G.2.1.4.1 Initial condition
6.2.3G.2.1.4.2 Test procedure
6.2.3G.2.1.4.3 Message contents
6.2.3G.2.1.5 Test Requirements
6.2.3G.2.2 Maximum Power Reduction (MPR) for V2X Communication / Power class 2 / Non-contiguous allocation of PSCCH and PSSCH /
6.2.3G.2.2.1 Test purpose
6.2.3G.2.2.2 Test applicability
6.2.3G.2.2.3 Minimum conformance requirements
6.2.3G.2.2.4 Test description
6.2.3G.2.2.4.1 Initial conditions
6.2.3G.2.2.4.2 Test procedure
6.2.3G.2.2.4.3 Message contents
6.2.3G.2.2.5 Test requirement
6.2.4 Additional Maximum Power Reduction (A-MPR)
6.2.4.1 Test purpose
6.2.4.2 Test applicability
6.2.4.3 Minimum conformance requirements
6.2.4.4 Test description
6.2.4.4.1 Initial condition
6.2.4.4.2 Test procedure
6.2.4.4.3 Message contents
6.2.4.5 Test requirements
6.2.4_1 Additional Maximum Power Reduction (A-MPR) for HPUE
6.2.4_1.2 Test applicability
6.2.4_1.3 Minimum conformance requirements
6.2.4_1.4 Test description
6.2.4_1.5 Test requirements
6.2.4_2 Additional Maximum Power Reduction (A-MPR) for UL 64QAM
6.2.4_2.1 Test purpose
6.2.4_2.2 Test applicability
6.2.4_2.3 Minimum conformance requirements
6.2.4_2.4 Test description
6.2.4_2.4.1 Initial condition
6.2.4_2.4.2 Test procedure
6.2.4_2.4.3 Message contents
6.2.4_2.5 Test requirements
6.2.4_3 Additional Maximum Power Reduction (A-MPR) with PUSCH frequency hopping
6.2.4_3.1 Test purpose
6.2.4_3.2 Test applicability
6.2.4_3.3 Minimum conformance requirements
6.2.4_3.4 Test description
6.2.4_3.5 Test requirements
6.2.4_4 Additional Maximum Power Reduction (A-MPR) for UL 256QAM
6.2.4_4.1 Test purpose
6.2.4_4.2 Test applicability
6.2.4_4.3 Minimum conformance requirements
6.2.4_4.4 Test description
6.2.4_4.4.1 Initial condition
6.2.4_4.4.2 Test procedure
6.2.4_4.4.3 Message contents
6.2.4_4.5 Test requirements
6.2.4A Additional Maximum Power Reduction (A-MPR) for CA
6.2.4A.1 Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA)
6.2.4A.1.1 Test purpose
6.2.4A.1.2 Test applicability
6.2.4A.1.3 Minimum conformance requirements
6.2.4A.1.3.5 A-MPR for CA_NS_05 for CA_38C
6.2.4A.1.3.6 A-MPR for CA_NS_06 for CA_7C
6.2.4A.1.3.7 A-MPR for CA_NS_07 for CA_39C
6.2.4A.1.4 Test description
6.2.4A.1.5 Test requirements
6.2.4A.1_1 Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM
6.2.4A.1_1.1 Test purpose
6.2.4A.1_1.2 Test applicability
6.2.4A.1_1.3 Minimum conformance requirements
6.2.4A.1_1.3.5 A-MPR for CA_NS_05 for CA_38C
6.2.4A.1_1.3.6 A-MPR for CA_NS_06 for CA_7C
6.2.4A.1_1.3.7 A-MPR for CA_NS_07 for CA_39C
6.2.4A.1_1.3.8 A-MPR for CA_NS_08 for CA_42C
6.2.4A.1_1.4 Test description
6.2.4A.1_1.5 Test requirements
6.2.4A.1_2 Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM
6.2.4A.1_2.1 Test purpose
6.2.4A.1_2.2 Test applicability
6.2.4A.1_2.3 Minimum conformance requirements
6.2.4A.1_2.3.5 A-MPR for CA_NS_05 for CA_38C
6.2.4A.1_2.3.6 A-MPR for CA_NS_06 for CA_7C
6.2.4A.1_2.3.7 A-MPR for CA_NS_07 for CA_39C
6.2.4A.1_2.4 Test description
6.2.4A.1_2.5 Test requirements
6.2.4A.2 Additional Maximum Power Reduction (A-MPR) for CA (inter-band DL CA and UL CA)
6.2.4A.2.1 Test purpose
6.2.4A.2.2 Test applicability
6.2.4A.2.3 Minimum conformance requirements
6.2.4A.2.4 Test description
6.2.4A.2.4.1 Initial conditions
6.2.4A.2.4.2 Test procedure
6.2.4A.2.4.3 Message contents
6.2.4A.2.5 Test requirements
6.2.4A.2_1 Additional Maximum Power Reduction (A-MPR) for CA (inter-band DL CA and UL CA) for UL 64QAM
6.2.4A.2_1.1 Test purpose
6.2.4A.2_1.2 Test applicability
6.2.4A.2_1.3 Minimum conformance requirements
6.2.4A.2_1.4 Test description
6.2.4A.2_1.4.1 Initial conditions
6.2.4A.2_1.4.2 Test procedure
6.2.4A.2_1.4.3 Message contents
6.2.4A.2_1.5 Test requirements
6.2.4A.2_2 Additional Maximum Power Reduction (A-MPR) for CA (inter-band DL CA and UL CA) for UL 256QAM
6.2.4A.2_2.1 Test purpose
6.2.4A.2_2.2 Test applicability
6.2.4A.2_2.3 Minimum conformance requirements
6.2.4A.2_2.4 Test description
6.2.4A.2_2.4.1 Initial conditions
6.2.4A.2_2.4.2 Test procedure
6.2.4A.2_2.4.3 Message contents
6.2.4A.2_2.5 Test requirements
6.2.4A.3 Additional Maximum Power Reduction (A-MPR) for CA (intra-band non-contiguous DL CA and UL CA)
6.2.4A.3.1 Minimum conformance requirements
6.2.4A.2_2 Void
6.2.4A.4 Additional Maximum Power Reduction (A-MPR) for CA (3UL CA)
6.2.4A.4.1 Test purpose
6.2.4A.4.2 Test applicability
6.2.4A.4.3 Minimum conformance requirements
6.2.4A.4.4 Test description
6.2.4A.4.4.1 Initial conditions
6.2.4A.4.5 Test Requirements
6.2.4B Additional Maximum Power Reduction (A-MPR) for UL-MIMO
6.2.4B.1 Test purpose
6.2.4B.2 Test applicability
6.2.4B.3 Minimum conformance requirements
6.2.4B.4 Test description
6.2.4B.4.1 Initial condition
6.2.4B.4.2 Test procedure
6.2.4B.4.3 Message contents
6.2.4B.5 Test requirements
6.2.4E Additional Maximum Power Reduction (A-MPR) for UE category 0
6.2.4E.1 Test purpose
6.2.4E.2 Test applicability
6.2.4E.3 Minimum conformance requirements
6.2.4E.4 Test description
6.2.4E.4.1 Initial condition
6.2.4E.4.2 Test procedure
6.2.4E.4.3 Message contents
6.2.4E.5 Test requirements
6.2.4EA Additional Maximum Power Reduction (A-MPR) for UE category M1
6.2.4EA.1 Test purpose
6.2.4EA.2 Test applicability
6.2.4EA.3 Minimum conformance requirements
6.2.4EA.4 Test description
6.2.4EA.4.1 Initial condition
6.2.4EA.4.2 Test procedure
6.2.4EA.4.3 Message contents
6.2.4EA.5 Test requirements
6.2.4EB Additional Maximum Power Reduction (A-MPR) for UE category 1bis
6.2.4EB.1 Test purpose
6.2.4EB.2 Test applicability
6.2.4EB.3 Minimum conformance requirements
6.2.4EB.4 Test description
6.2.4EB.4.1 Initial conditions
6.2.4EB.4.2 Test procedure
6.2.4EB.4.3 Message contents
6.2.4EB.5 Test requirement
6.2.4G Additional Maximum Power Reduction (A-MPR) for V2X Communication
6.2.4G.1 Additional Maximum Power Reduction (A-MPR) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.2.4G.1.1 Test purpose
6.2.4G.1.2 Test applicability
6.2.4G.1.3 Minimum conformance requirements
6.2.4G.1.4 Test description
6.2.4G.1.4.3 Message contents
6.2.4G.1.5 Test Requirements
6.2.4G.2 Additional Maximum Power Reduction (A-MPR) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink
6.2.4G.2.1 Test purpose
6.2.4G.2.2 Test applicability
6.2.4G.2.3 Minimum conformance requirements
6.2.4G.2.4 Test description
6.2.4G.2.4.3 Message contents
6.2.4G.2.5 Test Requirements
6.2.5 Configured UE transmitted Output Power
6.2.5.1 Test purpose
6.2.5.2 Test applicability
6.2.5.3 Minimum conformance requirements
6.2.5.4 Test description
6.2.5.4.1 Initial conditions
6.2.5.4.2 Test procedure
6.2.5.4.3 Message contents
6.2.5.5 Test requirement
6.2.5_1 Configured UE transmitted Output Power for HPUE
6.2.5_1.1 Test purpose
6.2.5_1.2 Test applicability
6.2.5_1.3 Minimum conformance requirements
6.2.5_1.4 Test description
6.2.5_1.4.1 Initial conditions
6.2.5_1.4.2 Test procedure
6.2.5_1.4.3 Message contents
6.2.5_1.5 Test requirement
6.2.5A Configured transmitted power for CA
6.2.5A.1 Configured UE transmitted Output Power for CA (intra-band contiguous DL CA and UL CA)
6.2.5A.1.1 Test purpose
6.2.5A.1.2 Test applicability
6.2.5A.1.3 Minimum conformance requirements
6.2.5A.1.4 Test description
6.2.5A.1.5 Test requirement
6.2.5A.2 Void
6.2.5A.3 Configured UE transmitted Output Power for CA (inter-band DL CA and UL CA)
6.2.5A.3.1 Test purpose
6.2.5A.3.2 Test applicability
6.2.5A.3.3 Minimum conformance requirements
6.2.5A.3.4 Test description
6.2.5A.3.5 Test requirement
6.2.5A.4 Configured UE transmitted Output Power for CA (intra-band non-contiguous DL CA and UL CA)
6.2.5A.4.1 Test purpose
6.2.5A.4.2 Test applicability
6.2.5A.4.3 Minimum conformance requirements
6.2.5A.4.4 Test description
6.2.5A.4.5 Test requirement
6.2.5A.5 Configured UE transmitted Output Power for CA (3UL CA)
6.2.5A.5.1 Test purpose
6.2.5A.5.2 Test applicability
6.2.5A.5.3 Minimum conformance requirements
6.2.5A.5.4 Test description
6.2.5A.5.5 Test requirement
6.2.5B Configured UE transmitted Output Power for UL-MIMO
6.2.5B.1 Test purpose
6.2.5B.2 Test applicability
6.2.5B.3 Minimum conformance requirements
6.2.5B.4 Test description
6.2.5B.4.1 Initial conditions
6.2.5B.4.2 Test procedure
6.2.5B.4.3 Message contents
6.2.5B.5 Test requirement
6.2.5E Configured UE transmitted Output Power for UE category 0
6.2.5E.1 Test purpose
6.2.5E.2 Test applicability
6.2.5E.3 Minimum conformance requirements
6.2.5E.4 Test description
6.2.5E.4.1 Initial conditions
6.2.5E.4.2 Test procedure
6.2.5E.4.3 Message contents
6.2.5E.5 Test requirement
6.2.5EA Configured UE transmitted Power for UE category M1
6.2.5EA.1 Test purpose
6.2.5EA.2 Test applicability
6.2.5EA.3 Minimum conformance requirements
6.2.5EA.4 Test description
6.2.5EA.4.1 Initial condition
6.2.5EA.4.2 Test procedure
6.2.5EA.4.3 Message contents
6.2.5EA.5 Test requirements
6.2.5EB Configured UE transmitted Power for UE category 1bis
6.2.5EB.1 Test purpose
6.2.5EB.2 Test applicability
6.2.5EB.3 Minimum conformance requirements
6.2.5EB.4 Test description
6.2.5EB.4.1 Initial conditions
6.2.5EB.4.2 Test procedure
6.2.5EB.4.3 Message contents
6.2.5EB.5 Test requirement
6.2.5EC Configured UE transmitted Power for UE category M2
6.2.5EC.1 Test purpose
6.2.5EC.2 Test applicability
6.2.5EC.3 Minimum conformance requirements
6.2.5EC.4 Test description
6.2.5EC.4.1 Initial condition
6.2.5EC.4.2 Test procedure
6.2.5EC.4.3 Message contents
6.2.5EC.5 Test requirements
6.2.5F Configured UE transmitted Output Power for UE category NB1 and NB2
6.2.5F.1 Test purpose
6.2.5F.2 Test applicability
6.2.5F.3 Minimum conformance requirements
6.2.5F.4 Test description
6.2.5F.4.1 Initial conditions
6.2.5F.4.2 Test procedure
6.2.5F.4.3 Message contents
6.2.5F.5 Test requirement
6.2.5FA Configured UE transmitted Output Power for UE category NB1 and NB2/Power Class 6
6.2.5FA.1 Test purpose
6.2.5FA.2 Test applicability
6.2.5FA.3 Minimum conformance requirements
6.2.5FA.4 Test description
6.2.5FA.4.1 Initial conditions
6.2.5FA.4.2 Test procedure
6.2.5FA.4.3 Message contents
6.2.5FA.5 Test requirement
6.2.5G Configured UE transmitted Output Power for V2X Communication
6.2.5G.1 Configured UE transmitted Output Power for V2X Communication / Non-concurrent with E-UTRA uplink transmission
6.2.5G.1.1 Test purpose
6.2.5G.1.2 Test applicability
6.2.5G.1.3 Minimum conformance requirements
6.2.5G.1.4 Test description
6.2.5G.1.5 Test requirements
6.2.5G.2 Configured UE transmitted Output Power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink tran
6.2.5G.2.1 Test purpose
6.2.5G.2.2 Test applicability
6.2.5G.2.3 Minimum conformance requirements
6.2.5G.2.4 Test description
6.2.5G.2.4.1 Initial conditions
6.2.5G.2.4.2 Test procedure
6.2.5G.2.4.3 Message contents
6.2.5G.2.5 Test requirements
6.2.5G.3 Configured UE transmitted Output Power for V2X Communication / Intra-band contiguous multi-carrier operation
6.2.5G.3.1 Test purpose
6.2.5G.3.2 Test applicability
6.2.5G.3.3 Minimum conformance requirements
6.2.5G.3.4 Test description
6.2.5G.3.4.1 Initial conditions
6.2.5G.3.4.2 Test procedure
6.2.5G.3.4.3 Message contents
6.2.5G.3.5 Test requirement
6.3 Output Power Dynamics
6.3.1 Void
6.3.2 Minimum Output Power
6.3.2.1 Test purpose
6.3.2.2 Test applicability
6.3.2.3 Minimum conformance requirements
6.3.2.4 Test description
6.3.2.4.1 Initial conditions
6.3.2.4.2 Test procedure
6.3.2.4.3 Message contents
6.3.2.5 Test requirement
6.3.2A Minimum Output Power for CA
6.3.2A.0 Minimum conformance requirements
6.3.2A.1 Minimum Output Power for CA (intra-band contiguous DL CA and UL CA)
6.3.2A.1.1 Test purpose
6.3.2A.1.2 Test applicability
6.3.2A.1.3 Minimum conformance requirements
6.3.2A.1.4 Test description
6.3.2A.1.4.1 Initial conditions
6.3.2A.1.4.2 Test procedure
6.3.2A.1.4.3 Message contents
6.3.2A.1.5 Test requirements
6.3.2A.2 Minimum Output Power for CA (inter-band DL CA and UL CA)
6.3.2A.2.1 Test purpose
6.3.2A.2.2 Test applicability
6.3.2A.2.3 Minimum conformance requirements
6.3.2A.2.4 Test description
6.3.2A.2.4.1 Initial conditions
6.3.2A.2.4.2 Test procedure
6.3.2A.2.4.3 Message contents
6.3.2A.2.5 Test requirements
6.3.2A.3 Minimum Output Power for CA (intra-band non-contiguous DL CA and UL CA)
6.3.2A.3.1 Test purpose
6.3.2A.3.2 Test applicability
6.3.2A.3.3 Minimum conformance requirements
6.3.2A.3.4 Test description
6.3.2A.3.4.1 Initial conditions
6.3.2A.3.4.2 Test procedure
6.3.2A.3.4.3 Message contents
6.3.2A.3.5 Test requirements
6.3.2A.4 Minimum Output Power for CA (3UL CA)
6.3.2A.4.1 Test purpose
6.3.2A.4.2 Test applicability
6.3.2A.4.3 Minimum conformance requirements
6.3.2A.4.4 Test description
6.3.2A.4.4.1 Initial conditions
6.3.2A.4.4.2 Test procedure
6.3.2A.4.4.3 Message contents
6.3.2A.4.5 Test requirements
6.3.2B Minimum Output Power for UL-MIMO
6.3.2B.1 Test purpose
6.3.2B.2 Test applicability
6.3.2B.3 Minimum conformance requirements
6.3.2B.4 Test description
6.3.2B.4.1 Initial conditions
6.3.2B.4.2 Test procedure
6.3.2B.4.3 Message contents
6.3.2B.5 Test requirement
6.3.2E Minimum Output Power for UE category 0
6.3.2E.1 Test purpose
6.3.2E.2 Test applicability
6.3.2E.3 Minimum conformance requirements
6.3.2E.4 Test description
6.3.2E.4.1 Initial conditions
6.3.2E.4.2 Test procedure
6.3.2E.4.3 Message contents
6.3.2E.5 Test requirement
6.3.2EA Minimum Output Power for UE category M1
6.3.2EA.1 Test purpose
6.3.2EA.2 Test applicability
6.3.2EA.3 Minimum conformance requirements
6.3.2EA.4 Test description
6.3.2EA.4.1 Initial condition
6.3.2EA.4.2 Test procedure
6.3.2EA.4.3 Message contents
6.3.2EA.5 Test requirements
6.3.2EB Minimum Output Power for UE category 1bis
6.3.2EB.1 Test purpose
6.3.2EB.2 Test applicability
6.3.2EB.3 Minimum conformance requirements
6.3.2EB.4 Test description
6.3.2EB.4.1 Initial conditions
6.3.2EB.4.2 Test procedure
6.3.2EB.4.3 Message contents
6.3.2EB.5 Test requirement
6.3.2EC Minimum Output Power for UE category M2
6.3.2EC.1 Test purpose
6.3.2EC.2 Test applicability
6.3.2EC.3 Minimum conformance requirements
6.3.2EC.4 Test description
6.3.2EC.4.1 Initial condition
6.3.2EC.4.2 Test procedure
6.3.2EC.4.3 Message contents
6.3.2EC.5 Test requirements
6.3.2F Minimum Output Power for category NB1 and NB2
6.3.2F.1 Test purpose
6.3.2F.2 Test applicability
6.3.2F.3 Minimum conformance requirements
6.3.2F.4 Test description
6.3.2F.4.1 Initial conditions
6.3.2F.4.2 Test procedure
6.3.2F.4.3 Message contents
6.3.2F.5 Test requirements
6.3.2G Minimum output power for V2X Communication
6.3.2G.1 Minimum output power for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.3.2G.1.1 Test purpose
6.3.2G.1.2 Test applicability
6.3.2G.1.3 Minimum conformance requirements
6.3.2G.1.4 Test description
6.3.2G.1.4.1 Initial conditions
6.3.2G.1.4.2 Test procedure
6.3.2G.1.4.3 Message contents
6.3.2G.1.5 Test requirements
6.3.2G.2 Minimum output power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
6.3.2G.2.1 Test purpose
6.3.2G.2.2 Test applicability
6.3.2G.2.3 Minimum conformance requirements
6.3.2G.2.4 Test description
6.3.2G.2.4.1 Initial conditions
6.3.2G.2.4.2 Test procedure
6.3.2G.2.4.3 Message contents
6.3.2G.2.5 Test requirements
6.3.2G.3 Minimum output power for V2X Communication / Intra-band contiguous multi-carrier operation
6.3.2G.3.1 Test purpose
6.3.2G.3.2 Test applicability
6.3.2G.3.3 Minimum conformance requirements
6.3.2G.3.4 Test description
6.3.2G.3.4.1 Initial conditions
6.3.2G.3.4.2 Test procedure
6.3.2G.3.4.3 Message contents
6.3.2G.3.5 Test requirements
6.3.3 Transmit OFF power
6.3.3.1 Test purpose
6.3.3.2 Test applicability
6.3.3.3 Minimum conformance requirement
6.3.3.4 Test description
6.3.3.5 Test requirement
6.3.3A UE Transmit OFF power for CA
6.3.3A.0 Minimum conformance requirements
6.3.3A.1 UE Transmit OFF power for CA (intra-band contiguous DL CA and UL CA)
6.3.3A.1.1 Test purpose
6.3.3A.1.2 Test applicability
6.3.3A.1.3 Minimum conformance requirements
6.3.3A.1.4 Test description
6.3.3A.1.5 Test Requirements
6.3.3A.2 UE Transmit OFF power for CA (inter-band DL CA and UL CA)
6.3.3A.2.1 Test purpose
6.3.3A.2.2 Test applicability
6.3.3A.2.3 Minimum conformance requirements
6.3.3A.2.4 Test description
6.3.3A.2.5 Test Requirements
6.3.3A.3 UE Transmit OFF power for CA (intra-band non-contiguous DL CA and UL CA)
6.3.3A.3.1 Test purpose
6.3.3A.3.2 Test applicability
6.3.3A.3.3 Minimum conformance requirements
6.3.3A.3.4 Test description
6.3.3A.3.5 Test Requirements
6.3.3A.4 UE Transmit OFF power for CA (3UL CA)
6.3.3A.4.1 Test purpose
6.3.3A.4.2 Test applicability
6.3.3A.4.3 Minimum conformance requirements
6.3.3A.4.4 Test description
6.3.3A.4.5 Test Requirements
6.3.3B UE Transmit OFF power for UL-MIMO
6.3.3B.1 Test purpose
6.3.3B.2 Test applicability
6.3.3B.3 Minimum conformance requirement
6.3.3B.4 Test description
6.3.3B.5 Test requirement
6.3.3C
6.3.3D UE Transmit OFF power for ProSe
6.3.3D.0 Minimum conformance requirements
6.3.3D.1 UE Transmit OFF power for ProSe Direct Discovery
6.3.3D.1.1 Test purpose
6.3.3D.1.2 Test applicability
6.3.3D.1.3 Minimum Conformance requirements
6.3.3D.1.4 Test description
6.3.3D.1.5 Test requirements
6.3.3E UE Transmit OFF power for UE category 0
6.3.3E.1 Test purpose
6.3.3E.2 Test applicability
6.3.3E.3 Minimum conformance requirement
6.3.3E.4 Test description
6.3.3E.5 Test requirement
6.3.3EA UE Transmit OFF power for UE category M1
6.3.3EA.1 Test purpose
6.3.3EA.2 Test applicability
6.3.3EA.3 Minimum conformance requirements
6.3.3EA.4 Test description
6.3.3EA.5 Test requirements
6.3.3EB UE Transmit OFF power for UE category 1bis
6.3.3EB.1 Test purpose
6.3.3EB.2 Test applicability
6.3.3EB.3 Minimum conformance requirements
6.3.3EB.4 Test description
6.3.3EB.5 Test requirement
6.3.3EC UE Transmit OFF power for UE category M2
6.3.3EC.1 Test purpose
6.3.3EC.2 Test applicability
6.3.3EC.3 Minimum conformance requirements
6.3.3EC.4 Test description
6.3.3EC.5 Test requirements
6.3.3F Transmit OFF power for category NB1 and NB2
6.3.3F.1 Test purpose
6.3.3F.2 Test applicability
6.3.3F.3 Minimum conformance requirement
6.3.3F.4 Test description
6.3.3F.5 Test requirement
6.3.3G UE Transmit OFF power for V2X Communication
6.3.3G.1 UE Transmit OFF power for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.3.3G.1.1 Test purpose
6.3.3G.1.2 Test applicability
6.3.3G.1.3 Minimum conformance requirements
6.3.3G.1.4 Test description
6.3.3G.1.5 Test requirements
6.3.3G.2 UE Transmit OFF power for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
6.3.3G.2.1 Test purpose
6.3.3G.2.2 Test applicability
6.3.3G.2.3 Minimum conformance requirements
6.3.3G.2.4 Test description
6.3.3G.2.5 Test requirements
6.3.3G.3 UE Transmit OFF power for V2X Communication / Intra-band contiguous multi-carrier operation
6.3.3G.3.1 Test purpose
6.3.3G.3.2 Test applicability
6.3.3G.3.3 Minimum conformance requirements
6.3.3G.3.4 Test description
6.3.3G.3.5 Test requirement
6.3.4 ON/OFF time mask
6.3.4.1 General ON/OFF time mask
6.3.4.1.1 Test purpose
6.3.4.1.2 Test applicability
6.3.4.1.3 Minimum conformance requirement
6.3.4.1.4 Test description
6.3.4.1.5 Test requirement
6.3.4.2 PRACH and SRS time mask
6.3.4.2.1 PRACH time mask
6.3.4.2.2 SRS time mask
6.3.4A ON/OFF time mask for CA
6.3.4A.0 Minimum conformance requirements
6.3.4A.1 General ON/OFF time mask for CA
6.3.4A.1.1 General ON/OFF time mask for CA (intra-band contiguous DL CA and UL CA)
6.3.4A.1.1.4.2 Test procedure
6.3.4A.1.1.4.3 Message contents
6.3.4A.1.1.5 Test requirement
6.3.4A.1.2 General ON/OFF time mask for CA (inter-band DL CA and UL CA)
6.3.4A.1.2.4.2 Test procedure
6.3.4A.1.2.4.3 Message contents
6.3.4A.1.2.5 Test requirement
6.3.4A.1.3 General ON/OFF time mask for CA (intra-band non-contiguous DL CA and UL CA)
6.3.4A.1.3.4.2 Test procedure
6.3.4A.1.3.4.3 Message contents
6.3.4A.1.3.5 Test requirement
6.3.4A.1.4 General ON/OFF time mask for CA (3UL CA)
6.3.4A.1.4.4.2 Test procedure
6.3.4A.1.4.4.3 Message contents
6.3.4A.1.4.5 Test requirement
6.3.4B ON/OFF time mask for UL-MIMO
6.3.4B.1 General ON/OFF time mask for UL-MIMO
6.3.4B.1.1 Test purpose
6.3.4B.1.2 Test applicability
6.3.4B.1.3 Minimum conformance requirement
6.3.4B.1.4 Test description
6.3.4B.1.5 Test requirement
6.3.4C ON/OFF time mask for DC
6.3.4C.1 General ON/OFF time mask for Dual Connectivity
6.3.4C.1.1 Test purpose
6.3.4C.1.2 Test applicability
6.3.4C.1.3 Minimum conformance requirements
6.3.4C.1.4 Test description
6.3.4C.1.4.1 Initial conditions
6.3.4C.1.4.2 Test procedure
6.3.4C.1.4.3 Message contents
6.3.4C.1.5 Test requirement
6.3.4C.1_1 General ON/OFF time mask for asynchronous Dual Connectivity
6.3.4C.1_1.1 Test purpose
6.3.4C.1_1.2 Test applicability
6.3.4C.1_1.3 Minimum conformance requirements
6.3.4C.1_1.4 Test description
6.3.4C.1_1.4.1 Initial conditions
6.3.4C.1_1.4.2 Test procedure
6.3.4C.1_1.4.3 Message contents
6.3.4C.1_1.5 Test requirement
6.3.4E ON/OFF time mask for UE category 0
6.3.4E.1 General ON/OFF time mask for UE category 0
6.3.4E.1.1 Test purpose
6.3.4E.1.2 Test applicability
6.3.4E.1.3 Minimum conformance requirement
6.3.4E.1.4 Test description
6.3.4E.1.5 Test requirement
6.3.4E.2 PRACH and SRS time mask for UE category 0
6.3.4E.2.1 PRACH time mask for UE category 0
6.3.4E.2.2 SRS time mask for UE category 0
6.3.4EA ON/OFF time mask for UE category M1
6.3.4EA.1 General ON/OFF time mask for UE category M1
6.3.4EA.1.1 Test purpose
6.3.4EA.1.2 Test applicability
6.3.4EA.1.3 Minimum conformance requirement
6.3.4EA.1.4 Test description
6.3.4EA.1.5 Test requirement
6.3.4EA.2 PRACH and SRS ON/OFF time mask for UE category M1
6.3.4EA.2.1 PRACH time mask for UE category M1
6.3.4EA.2.2 SRS time mask for UE category M1
6.3.4EB ON/OFF time mask for UE category 1bis
6.3.4EB.1 General ON/OFF time mask for UE category 1bis
6.3.4EB.1.1 Test purpose
6.3.4EB.1.2 Test applicability
6.3.4EB.1.3 Minimum conformance requirement
6.3.4EB.1.4 Test description
6.3.4EB.1.5 Test requirement
6.3.4EB.2 PRACH and SRS ON/OFF time mask for UE category 1bis
6.3.4EB.2.1 PRACH time mask for UE category 1bis
6.3.4EB.2.1.1 Test purpose
6.3.4EB.2.1.2 Test applicability
6.3.4EB.2.1.3 Minimum conformance requirement
6.3.4EB.2.1.4 Test description
6.3.4EB.2.1.4.1 Initial conditions
6.3.4EB.2.1.4.2 Test procedure
6.3.4EB.2.1.4.3 Message contents
6.3.4EB.2.1.5 Test requirement
6.3.4EB.2.2 SRS time mask for UE category 1bis
6.3.4EB.2.2.1 Test purpose
6.3.4EB.2.2.2 Test applicability
6.3.4EB.2.2.3 Minimum conformance requirement
6.3.4EB.2.2.4 Test description
6.3.4EB.2.2.4.1 Initial conditions
6.3.4EB.2.2.4.2 Test procedure
6.3.4EB.2.2.4.3 Message contents
6.3.4EB.2.2.5 Test requirement
6.3.4EC ON/OFF time mask for UE category M2
6.3.4EC.1 General ON/OFF time mask for UE category M2
6.3.4EC.1.1 Test purpose
6.3.4EC.1.2 Test applicability
6.3.4EC.1.3 Minimum conformance requirement
6.3.4EC.1.4 Test description
6.3.4EC.1.5 Test requirement
6.3.4F ON/OFF time mask for category NB1 and NB2
6.3.4F.1 General ON/OFF time mask for category NB1 and NB2
6.3.4F.1.1 Test purpose
6.3.4F.1.2 Test applicability
6.3.4F.1.3 Minimum conformance requirement
6.3.4F.1.4 Test description
6.3.4F.1.5 Test requirement
6.3.4F.2 NPRACH time mask for category NB1 and NB2
6.3.4F.2.1 Test purpose
6.3.4F.2.2 Test applicability
6.3.4F.2.3 Minimum conformance requirement
6.3.4F.2.4 Test description
6.3.4F.2.5 Test requirement
6.3.4G ON/OFF time mask for V2X Communication
6.3.4G.1 General ON/OFF time mask for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.3.4G.1.1 Test purpose
6.3.4G.1.2 Test applicability
6.3.4G.1.3 Minimum conformance requirements
6.3.4G.1.4 Test description
6.3.4G.1.4.1 Initial conditions
6.3.4G.1.4.2 Test procedure
6.3.4G.1.4.3 Message contents
6.3.4G.1.5 Test requirement
6.3.4G.2 General ON/OFF time mask for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
6.3.4G.2.1 Test purpose
6.3.4G.2.2 Test applicability
6.3.4G.2.3 Minimum conformance requirements
6.3.4G.2.4 Test description
6.3.4G.2.4.1 Initial conditions
6.3.4G.2.4.2 Test procedure
6.3.4G.2.4.3 Message contents
6.3.4G.2.5 Test requirement
6.3.4G.3 General ON/OFF time mask for V2X Communication / Intra-band contiguous multi-carrier operation
6.3.4G.3.1 Test purpose
6.3.4G.3.2 Test applicability
6.3.4G.3.3 Minimum conformance requirements
6.3.4G.3.4 Test description
6.3.4G.3.4.1 Initial conditions
6.3.4G.3.4.2 Test procedure
6.3.4G.3.4.3 Message contents
6.3.4G.3.5 Test requirement
6.3.4G.4 PSSS/SSSS time mask for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.3.4G.4.1 Test purpose
6.3.4G.4.2 Test applicability
6.3.4G.4.3 Minimum conformance requirements
6.3.4G.4.4 Test description
6.3.4G.4.4.1 Initial conditions
6.3.4G.4.4.2 Test procedure
6.3.4G.4.4.3 Message contents
6.3.4G.4.5 Test requirement
6.3.5 Power Control
6.3.5.1 Power Control Absolute power tolerance
6.3.5.1.1 Test purpose
6.3.5.1.2 Test applicability
6.3.5.1.3 Minimum conformance requirement
6.3.5.1.4 Test description
6.3.5.1.5 Test requirement
6.3.5.2 Power Control Relative power tolerance
6.3.5.2.1 Test purpose
6.3.5.2.2 Test applicability
6.3.5.2.3 Minimum conformance requirement
6.3.5.2.4 Test description
6.3.5.2.5 Test requirement
6.3.5.3 Aggregate power control tolerance
6.3.5.3.1 Test purpose
6.3.5.3.2 Test applicability
6.3.5.3.3 Minimum conformance requirement
6.3.5.3.4 Test description
6.3.5.3.5 Test requirement
6.3.5_1 Power Control for HPUE
6.3.5_1.1 Power Control Absolute power tolerance for HPUE
6.3.5_1.1.1 Test purpose
6.3.5_1.1.2 Test applicability
6.3.5_1.1.3 Minimum conformance requirement
6.3.5_1.1.4 Test description
6.3.5_1.1.5 Test requirement
6.3.5_1.2 Power Control Relative power tolerance for HPUE
6.3.5_1.2.1 Test purpose
6.3.5_1.2.2 Test applicability
6.3.5_1.2.3 Minimum conformance requirement
6.3.5_1.2.4 Test description
6.3.5_1.2.5 Test requirement
6.3.5_1.3 Aggregate power control tolerance for HPUE
6.3.5_1.3.1 Test purpose
6.3.5_1.3.2 Test applicability
6.3.5_1.3.3 Minimum conformance requirement
6.3.5_1.3.4 Test description
6.3.5_1.3.5 Test requirement
6.3.5A Power Control for CA
6.3.5A.1 Power Control Absolute power tolerance for CA
6.3.5A.1.0 Minimum conformance requirements
6.3.5A.1.1 Power Control Absolute power tolerance for CA (intra-band contiguous DL CA and UL CA)
6.3.5A.1.2 Power Control Absolute power tolerance for CA (inter-band DL CA and UL CA)
6.3.5A.1.3 Power Control Absolute power tolerance for CA (intra-band non-contiguous DL CA and UL CA)
6.3.5A.1.4 Power Control Absolute power tolerance for CA (3UL CA)
6.3.5A.1.4.1 Test purpose
6.3.5A.1.4.2 Test applicability
6.3.5A.1.4.3 Minimum conformance requirements
6.3.5A.1.4.4 Test description
6.3.5A.1.4.5 Test Requirements
6.3.5A.1.5 Power Control Absolute power tolerance for CA(SRS carrier based switching)
6.3.5A.2 Power Control Relative power tolerance for CA
6.3.5A.2.0 Minimum conformance requirements
6.3.5A.2.1 Power Control Relative power tolerance for CA (intra-band contiguous DL CA and UL CA)
6.3.5A.2.2 Power Control Relative power tolerance for CA (inter-band DL CA and UL CA)
6.3.5A.2.3 Power Control Relative power tolerance for CA (intra-band non-contiguous DL CA and UL CA)
6.3.5A.2.4 Power Control Relative power tolerance for CA (3UL CA)
6.3.5A.2.4.1 Power Control Relative power tolerance for CA (intra-band contiguous 3DL CA and 3UL CA)
6.3.5A.2.4.1.1 Test purpose
6.3.5A.2.4.1.2 Test applicability
6.3.5A.2.4.1.3 Minimum conformance requirements
6.3.5A.2.4.1.4 Test description
6.3.5A.2.4.1.4.1 Initial conditions
6.3.5A.2.4.1.4.2 Test procedure
6.3.5A.2.4.1.4.3 Message contents
6.3.5A.2.4.1.5 Test Requirements
6.3.5A.2.4.2 Power Control Relative power tolerance for CA (inter-band 3DL CA and 3UL CA)
6.3.5A.2.4.2.1 Test purpose
6.3.5A.2.4.2.2 Test applicability
6.3.5A.2.4.2.3 Minimum conformance requirement
6.3.5A.2.4.2.4 Test description
6.3.5A.2.4.2.4.1 Initial conditions
6.3.5A.2.4.2.4.2 Test procedure
6.3.5A.2.4.2.4.3 Message contents
6.3.5A.2.4.2.5 Test requirement
6.3.5A.2.4.3 Power Control Relative power tolerance for CA (intra-band non-contiguous 3DL CA and 3UL CA)
6.3.5A.2.4.3.1 Test purpose
6.3.5A.2.4.3.2 Test applicability
6.3.5A.2.4.3.3 Minimum conformance requirement
6.3.5A.2.4.3.4 Test description
6.3.5A.2.4.3.4.1 Initial conditions
6.3.5A.2.4.3.4.2 Test procedure
6.3.5A.2.4.3.4.3 Message contents
6.3.5A.2.4.3.5 Test requirement
6.3.5A.3 Aggregate power control tolerance for CA
6.3.5A.3.0 Minimum conformance requirements
6.3.5A.3.1 Aggregate power control tolerance for CA (intra-band contiguous DL CA and UL CA)
6.3.5A.3.2 Aggregate power control tolerance for CA (inter-band DL CA and UL CA)
6.3.5A.3.3 Aggregate power control tolerance for CA (intra-band non-contiguous DL CA and UL CA)
6.3.5A.3.4 Aggregate Power Control Tolerance for CA (3UL CA)
6.3.5A.3.4.1 Test purpose
6.3.5A.3.4.2 Test applicability
6.3.5A.3.4.3 Minimum conformance requirements
6.3.5A.3.4.4 Test description
6.3.5A.3.4.5 Test Requirements
6.3.5B Power Control for UL- MIMO
6.3.5B.1 Power Control Absolute Power Tolerance for UL- MIMO
6.3.5B.1.1 Test purpose
6.3.5B.1.2 Test applicability
6.3.5B.1.3 Minimum conformance requirement
6.3.5B.1.4 Test description
6.3.5B.1.5 Test requirement
6.3.5B.2 Power Control Relative power tolerance for UL-MIMO
6.3.5B.2.1 Test purpose
6.3.5B.2.2 Test applicability
6.3.5B.2.3 Minimum conformance requirement
6.3.5B.2.4 Test description
6.3.5B.2.5 Test requirement
6.3.5B.3 Aggregate power control tolerance for UL-MIMO
6.3.5B.3.1 Test purpose
6.3.5B.3.2 Test applicability
6.3.5B.3.3 Minimum conformance requirement
6.3.5B.3.4 Test description
6.3.5B.3.5 Test requirement
6.3.5C Power Control for DC
6.3.5C.1
6.3.5C.2 Power Control Relative power tolerance for Dual Connectivity
6.3.5C.2_1 Power Control Relative power tolerance for asynchronous Dual Connectivity
6.3.5D
6.3.5E Power Control for UE category 0
6.3.5E.1 Power Control Absolute power tolerance for UE category 0
6.3.5E.1.1 Test purpose
6.3.5E.1.2 Minimum conformance requirement
6.3.5E.1.3 Test applicability
6.3.5E.1.4 Test description
6.3.5E.1.5 Test requirement
6.3.5E.2 Power Control Relative power tolerance for UE category 0
6.3.5E.2.1 Test purpose
6.3.5E.2.2 Test applicability
6.3.5E.2.3 Minimum conformance requirement
6.3.5E.2.4 Test description
6.3.5E.2.5 Test requirement
6.3.5E.3 Aggregate power control tolerance for UE category 0
6.3.5E.3.1 Test purpose
6.3.5E.3.2 Test applicability
6.3.5E.3.3 Minimum conformance requirement
6.3.5E.3.4 Test description
6.3.5E.3.5 Test requirement
6.3.5EA Power control for UE category M1
6.3.5EA.1 Power Control Absolute power tolerance for UE category M1
6.3.5EA.1.1 Test purpose
6.3.5EA.1.2 Test applicability
6.3.5EA.1.3 Minimum conformance requirement
6.3.5EA.1.4 Test description
6.3.5EA.1.5 Test requirement
6.3.5EA.2 Power Control Relative power tolerance for UE category M1
6.3.5EA.2.1 Test purpose
6.3.5EA.2.2 Test applicability
6.3.5EA.2.3 Minimum conformance requirement
6.3.5EA.2.4 Test description
6.3.5EA.2.5 Test requirement
6.3.5EA.3 Aggregate power control tolerance for UE category M1
6.3.5EA.3.1 Test purpose
6.3.5EA.3.2 Test applicability
6.3.5EA.3.3 Minimum conformance requirement
6.3.5EA.3.4 Test description
6.3.5EA.3.5 Test requirement
6.3.5EA.3_1 Aggregate power control tolerance for UE category M1 (CE Mode B)
6.3.5EA.3_1.1 Test purpose
6.3.5EA.3_1.2 Test applicability
6.3.5EA.3_1.3 Minimum conformance requirement
6.3.5EA.3_1.4 Test description
6.3.5EA.3_1.5 Test requirement
6.3.5EB Power Control for UE category 1bis
6.3.5EB.1 Power Control Absolute power tolerance for UE category 1bis
6.3.5EB.1.1 Test purpose
6.3.5EB.1.2 Test applicability
6.3.5EB.1.3 Minimum conformance requirement
6.3.5EB.1.4 Test description
6.3.5EB.1.4.1 Initial conditions
6.3.5EB.1.4.2 Test procedure
6.3.5EB.1.4.3 Message contents
6.3.5EB.1.5 Test requirements
6.3.5EB.2 Power Control Relative power tolerance for UE category 1bis
6.3.5EB.2.1 Test purpose
6.3.5EB.2.2 Test applicability
6.3.5EB.2.3 Minimum conformance requirement
6.3.5EB.2.4 Test description
6.3.5EB.2.4.1 Initial conditions
6.3.5EB.2.4.2 Test procedure
6.3.5EB.2.4.3 Message contents
6.3.5EB.2.5 Test requirements
6.3.5EB.3 Aggregate power control tolerance for UE category 1bis
6.3.5EB.3.1 Test purpose
6.3.5EB.3.2 Test applicability
6.3.5EB.3.3 Minimum conformance requirement
6.3.5EB.3.4 Test description
6.3.5EB.3.4.1 Initial conditions
6.3.5EB.3.4.2 Test procedure
6.3.5EB.3.4.3 Message contents
6.3.5EB.3.5 Test requirements
6.3.5EC
6.3.5EC.1 Power Control Absolute power tolerance for UE category M2
6.3.5EC.1.1 Test purpose
6.3.5EC.1.2 Test applicability
6.3.5EC.1.3 Minimum conformance requirement
6.3.5EC.1.4 Test description
6.3.5EC.1.5 Test requirement
6.3.5EC.2 Power Control Relative power tolerance for UE category M2
6.3.5EC.2.1 Test purpose
6.3.5EC.2.2 Test applicability
6.3.5EC.2.3 Minimum conformance requirement
6.3.5EC.2.4 Test description
6.3.5EC.2.5 Test requirement
6.3.5EC.3 Aggregate power control tolerance for UE category M2
6.3.5EC.3.1 Test purpose
6.3.5EC.3.2 Test applicability
6.3.5EC.3.3 Minimum conformance requirement
6.3.5EC.3.4 Test description
6.3.5EC.3.5 Test requirement
6.3.5F Power Control for category NB1 and NB2
6.3.5F.1 Power Control Absolute power tolerance for category NB1 and NB2
6.3.5F.1.1 Test purpose
6.3.5F.1.2 Test applicability
6.3.5F.1.3 Minimum conformance requirements
6.3.5F.1.4 Test description
6.3.5F.1.5 Test requirement
6.3.5F.2 Power Control Relative power tolerance for category NB1 and NB2
6.3.5F.2.1 Test purpose
6.3.5F.2.2 Test applicability
6.3.5F.2.3 Minimum conformance requirements
6.3.5F.2.4 Test description
6.3.5F.2.5 Test requirement
6.3.5F.3 Aggregate power control tolerance for category NB1 and NB2
6.3.5F.3.1 Test purpose
6.3.5F.3.2 Test applicability
6.3.5F.3.3 Minimum conformance requirement
6.3.5F.3.4 Test description
6.3.5FA Power Control for category NB1 and NB2/Power Class 6
6.3.5FA.1 Power Control Absolute power tolerance for category NB1 and NB2/Power Class 6
6.3.5FA.1.1 Test purpose
6.3.5FA.1.2 Test applicability
6.3.5FA.1.3 Minimum conformance requirements
6.3.5FA.1.4 Test description
6.3.5FA.1.5 Test requirement
6.3.5FA.2 Power Control Relative power tolerance for category NB1 and NB2/Power Class 6
6.3.5FA.2.1 Test purpose
6.3.5FA.2.2 Test applicability
6.3.5FA.2.3 Minimum conformance requirements
6.3.5FA.2.4 Test description
6.3.5FA.2.5 Test requirement
6.3.5FA.3 Aggregate power control tolerance for category NB1 and NB2/Power Class 6
6.3.5FA.3.1 Test purpose
6.3.5FA.3.2 Test applicability
6.3.5FA.3.3 Minimum conformance requirements
6.3.5FA.3.4 Test description
6.3.5FA.3.5 Test requirement
6.3.5G Power Control Absolute power tolerance for V2X Communication
6.3.5G.1 Power Control Absolute power tolerance for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.3.5G.2 Power Control Absolute power tolerance for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink tran
6.3.5G.3 Power Control Absolute power tolerance for V2X Communication / Intra-band contiguous multi-carrier operation
6.4 Void
6.5 Transmit signal quality
6.5.1 Frequency Error
6.5.1.1 Test purpose
6.5.1.2 Test applicability
6.5.1.3 Minimum conformance requirements
6.5.1.4 Test description
6.5.1.4.1 Initial condition
6.5.1.4.2 Test procedure
6.5.1.4.3 Message contents
6.5.1.5 Test requirement
6.5.1A Frequency error for CA
6.5.1A.0 Minimum conformance requirements
6.5.1A.1 Frequency error for CA (intra-band contiguous DL CA and UL CA)
6.5.1A.1.1 Test purpose
6.5.1A.1.2 Test applicability
6.5.1A.1.3 Minimum conformance requirements
6.5.1A.1.4 Test description
6.5.1A.1.5 Test Requirements
6.5.1A.2 Frequency error for CA (inter-band DL CA and UL CA)
6.5.1A.2.1 Test purpose
6.5.1A.2.2 Test applicability
6.5.1A.2.3 Minimum conformance requirements
6.5.1A.2.4 Test description
6.5.1A.2.4.3 Message contents
6.5.1A.2.5 Test requirement
6.5.1A.3 Frequency error for CA (intra-band non-contiguous DL CA and UL CA)
6.5.1A.3.1 Test purpose
6.5.1A.3.2 Test applicability
6.5.1A.3.3 Minimum conformance requirements
6.5.1A.3.4 Test description
6.5.1A.3.5 Test Requirements
6.5.1A.4 Frequency error for CA (3UL CA)
6.5.1A.4.1 Test purpose
6.5.1A.4.2 Test applicability
6.5.1A.4.3 Minimum conformance requirements
6.5.1A.4.4 Test description
6.5.1A.5 Test Requirements
6.5.1B Frequency Error for UL-MIMO
6.5.1B.1 Test purpose
6.5.1B.2 Test applicability
6.5.1B.3 Minimum conformance requirements
6.5.1B.4 Test description
6.5.1B.4.1 Initial condition
6.5.1B.4.2 Test procedure
6.5.1B.4.3 Message contents
6.5.1B.5 Test requirement
6.5.1C
6.5.1D Frequency Error for ProSe
6.5.1D.0 Minimum conformance requirements
6.5.1D.1 Frequency error for ProSe Direct Discovery
6.5.1D.1.1 Test purpose
6.5.1D.1.2 Test applicability
6.5.1D.1.3 Minimum conformance requirements
6.5.1D.1.4 Test description
6.5.1D.1.5 Test requirement
6.5.1D.2 Frequency error for ProSe Direct Communication
6.5.1D.2.1 Test purpose
6.5.1D.2.2 Test applicability
6.5.1D.2.3 Minimum conformance requirements
6.5.1D.2.4 Test description
6.5.1D.2.5 Test requirements
6.5.1E Frequency Error for UE category 0
6.5.1E.1 Test purpose
6.5.1E.2 Test applicability
6.5.1E.3 Minimum conformance requirements
6.5.1E.4 Test description
6.5.1E.4.1 Initial condition
6.5.1E.4.2 Test procedure
6.5.1E.4.3 Message contents
6.5.1E.5 Test requirement
6.5.1EA Frequency Error for UE category M1
6.5.1EA.1 Test purpose
6.5.1EA.2 Test applicability
6.5.1EA.3 Minimum conformance requirements
6.5.1EA.4 Test description
6.5.1EA.4.1 Initial condition
6.5.1EA.4.2 Test procedure
6.5.1EA.4.3 Message contents
6.5.1EA.5 Test requirement
6.5.1EA_1 Frequency Error for UE category M1 (CEmodeB)
6.5.1EA_1.1 Test purpose
6.5.1EA_1.2 Test applicability
6.5.1EA_1.3 Minimum conformance requirements
6.5.1EA_1.4 Test description
6.5.1EA_1.4.1 Initial condition
6.5.1EA_1.4.2 Test procedure
6.5.1EA_1.4.3 Message contents
6.5.1EA_1.5 Test requirement
6.5.1EB Frequency Error for UE category 1bis
6.5.1EB.1 Test purpose
6.5.1EB.2 Test applicability
6.5.1EB.3 Minimum conformance requirements
6.5.1EB.4 Test description
6.5.1EB.4.1 Initial conditions
6.5.1EB.4.2 Test procedure
6.5.1EB.4.3 Message contents
6.5.1EB.5 Test requirement
6.5.1EC Frequency Error for UE category M2
6.5.1EC.1 Test purpose
6.5.1EC.2 Test applicability
6.5.1EC.3 Minimum conformance requirements
6.5.1EC.4 Test description
6.5.1EC.4.1 Initial condition
6.5.1EC.4.2 Test procedure
6.5.1EC.4.3 Message contents
6.5.1EC.5 Test requirements
6.5.1F Frequency Error for category NB1 and NB2
6.5.1F.1 Test purpose
6.5.1F.2 Test applicability
6.5.1F.3 Minimum conformance requirements
6.5.1F.4 Test description
6.5.1F.4.1 Initial conditions
6.5.1F.4.2 Test procedure
6.5.1F.4.3 Message contents
6.5.1F.5 Test requirement
6.5.1G Frequency Error for V2X Communication
6.5.1G.1 Frequency Error for V2X Communication / Non-concurrent with E-UTRA uplink transmission
6.5.1G.1.1 Test purpose
6.5.1G.1.2 Test applicability
6.5.1G.1.3 Minimum Conformance Requirements
6.5.1G.1.4 Test description
6.5.1G.1.4.1 Initial condition
6.5.1G.1.4.2 Test procedure
6.5.1G.1.4.3 Message contents
6.5.1G.1.5 Test requirement
6.5.1G.2 Frequency error for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
6.5.2 Transmit modulation
6.5.2.1 Error Vector Magnitude (EVM)
6.5.2.1.1 Test Purpose
6.5.2.1.2 Test applicability
6.5.2.1.3 Minimum conformance requirements
6.5.2.1.4 Test description
6.5.2.1.5 Test requirement
6.5.2.1_1 Error Vector Magnitude (EVM) for UL 64QAM
6.5.2.1_1.1 Test Purpose
6.5.2.1_1.2 Test applicability
6.5.2.1_1.3 Minimum conformance requirements
6.5.2.1_1.4 Test description
6.5.2.1_1.5 Test requirement
6.5.2.1_2 Error Vector Magnitude (EVM) for UL 256QAM
6.5.2.1_2.1 Test Purpose
6.5.2.1_2.2 Test applicability
6.5.2.1_2.3 Minimum conformance requirements
6.5.2.1_2.4 Test description
6.5.2.1_2.5 Test requirement
6.5.2.1A PUSCH-EVM with exclusion period
6.5.2.1A.1 Test purpose
6.5.2.1A.2 Test applicability
6.5.2.1A.3 Minimum conformance requirement
6.5.2.1A.4 Test description
6.5.2.1A.5 Test requirement
6.5.2.1E Error Vector Magnitude (EVM) for UE category 0
6.5.2.1E.1 Error Vector Magnitude (EVM) for UE category 0
6.5.2.1E.2 PUSCH-EVM with exclusion period for UE category 0
6.5.2.1EA Error Vector Magnitude (EVM) for UE category M1
6.5.2.1EA.1 Error Vector Magnitude (EVM) for UE category M1
6.5.2.1EA.2 PUSCH-EVM with exclusion period for UE category M1
6.5.2.1EB Error Vector Magnitude (EVM) for UE category 1bis
6.5.2.1EB.1 Test purpose
6.5.2.1EB.2 Test applicability
6.5.2.1EB.3 Minimum conformance requirements
6.5.2.1EB.4 Test description
6.5.2.1EB.5 Test requirement
6.5.2.1EC Error Vector Magnitude (EVM) for UE category M2
6.5.2.1EC.1 Error Vector Magnitude (EVM) for UE category M2
6.5.2.1F.1 Error Vector Magnitude (EVM) for category NB1 and NB2
6.5.2.1F.1.1 Test Purpose
6.5.2.1F.1.2 Test applicability
6.5.2.1F.1.3 Minimum conformance requirements
6.5.2.1F.1.4 Test description
6.5.2.1F.1.5 Test requirement
6.5.2.1G Error Vector Magnitude (EVM) for V2X Communication
6.5.2.1G.0 Minimum conformance requirements
6.5.2.1G.1 Error Vector Magnitude (EVM) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.5.2.1G.1.1 Test Purpose
6.5.2.1G.1.2 Test applicability
6.5.2.1G.1.3 Minimum conformance requirements
6.5.2.1G.1.4 Test description
6.5.2.1G.1.4.1 Initial conditions
6.5.2.1G.1.4.2 Test procedure
6.5.2.1G.1.4.3 Message contents
6.5.2.1G.1.5 Test requirement
6.5.2.1G.2 Error Vector Magnitude (EVM) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmission
6.5.2.1G.2.1 Test Purpose
6.5.2.1G.2.2 Test applicability
6.5.2.1G.2.3 Minimum conformance requirements
6.5.2.1G.2.4 Test description
6.5.2.1G.2.4.1 Initial conditions
6.5.2.1G.2.4.2 Test procedure
6.5.2.1G.2.4.3 Message contents
6.5.2.1G.2.5 Test requirement
6.5.2.1G.3 Error Vector Magnitude (EVM) for V2X Communication / Intra-band contiguous multi-carrier operation
6.5.2.1G.3.1 Test Purpose
6.5.2.1G.3.2 Test applicability
6.5.2.1G.3.3 Minimum conformance requirements
6.5.2.1G.3.4 Test description
6.5.2.1G.3.4.1 Initial conditions
6.5.2.1G.3.4.2 Test procedure
6.5.2.1G.3.4.3 Message contents
6.5.2.1G.3.5 Test requirement
6.5.2.2 Carrier leakage
6.5.2.2.1 Test Purpose
6.5.2.2.2 Test applicability
6.5.2.2.3 Minimum conformance requirements
6.5.2.2.4 Test description
6.5.2.2.5 Test requirement
6.5.2.2E Carrier leakage for UE category 0
6.5.2.2E.1 Test Purpose
6.5.2.2E.2 Test applicability
6.5.2.2E.3 Minimum conformance requirements
6.5.2.2E.4 Test description
6.5.2.2E.5 Test requirement
6.5.2.2EA Carrier leakage for UE category M1
6.5.2.2EA.1 Test Purpose
6.5.2.2EA.2 Test applicability
6.5.2.2EA.3 Minimum conformance requirements
6.5.2.2EA.4 Test description
6.5.2.2EA.5 Test requirement
6.5.2.2EB Carrier leakage for UE category 1bis
6.5.2.2EB.1 Test purpose
6.5.2.2EB.2 Test applicability
6.5.2.2EB.3 Minimum conformance requirements
6.5.2.2EB.4 Test description
6.5.2.2EB.5 Test requirement
6.5.2.2F Carrier leakage for category NB1 and NB2
6.5.2.2F.1 Test Purpose
6.5.2.2F.2 Test applicability
6.5.2.2F.3 Minimum conformance requirements
6.5.2.2F.4 Test description
6.5.2.2F.5 Test requirement
6.5.2.2G Carrier leakage for V2X Communication
6.5.2.2G.0 Minimum conformance requirements
6.5.2.2G.1 Carrier leakage for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.5.2.2G.1.1 Test Purpose
6.5.2.2G.1.2 Test applicability
6.5.2.2G.1.3 Minimum conformance requirements
6.5.2.2G.1.4 Test description
6.5.2.2G.1.4.1 Initial conditions
6.5.2.2G.1.4.2 Test procedure
6.5.2.2G.1.4.3 Message contents
6.5.2.2G.1.5 Test requirement
6.5.2.3 In-band emissions for non allocated RB
6.5.2.3.1 Test Purpose
6.5.2.3.2 Test applicability
6.5.2.3.3 Minimum conformance requirements
6.5.2.3.4 Test description
6.5.2.3.5 Test requirement
6.5.2.3E In-band emissions for non allocated RB for UE category 0
6.5.2.3E.1 Test Purpose
6.5.2.3E.2 Test applicability
6.5.2.3E.3 Minimum conformance requirements
6.5.2.3E.4 Test description
6.5.2.3E.5 Test requirement
6.5.2.3EA In-band emissions for non allocated RB for UE category M1
6.5.2.3EA.1 Test Purpose
6.5.2.3EA.2 Test applicability
6.5.2.3EA.3 Minimum conformance requirements
6.5.2.3EA.4 Test description
6.5.2.3EA.5 Test requirement
6.5.2.3EB In-band emissions for non allocated RB for UE category 1bis
6.5.2.3EB.1 Test purpose
6.5.2.3EB.2 Test applicability
6.5.2.3EB.3 Minimum conformance requirements
6.5.2.3EB.4 Test description
6.5.2.3EB.5 Test requirement
6.5.2.3F In-band emissions for non allocated RB for category NB1 and NB2
6.5.2.3F.1 Test purpose
6.5.2.3F.2 Test applicability
6.5.2.3F.3 Minimum conformance requirements
6.5.2.3F.4 Test description
6.5.2.3F.4.1 Initial conditions
6.5.2.3F.4.2 Test procedure
6.5.2.3F.4.3 Message contents
6.5.2.3F.5 Test requirement
6.5.2.3G In-band emissions for non-allocated RB for V2X Communication
6.5.2.3G.1 In-band emissions for non-allocated RB for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.5.2.3G.1.1 Test Purpose
6.5.2.3G.1.2 Test applicability
6.5.2.3G.1.3 Minimum conformance requirements
6.5.2.3G.1.4 Test description
6.5.2.3G.1.4.1 Initial conditions
6.5.2.3G.1.4.2 Test procedure
6.5.2.3G.1.4.3 Message contents
6.5.2.3G.1.5 Test requirement
6.5.2.3G.2 In-band emissions for non-allocated RB for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink tr
6.5.2.3G.3 In-band emissions for non-allocated RB for V2X Communication / Intra-band contiguous MCC operation
6.5.2.3G.3.2 Test Applicability
6.5.2.3G.3.3 Minimum conformance requirements
6.5.2.3G.3.4.3 Message Contents
6.5.2.3G.3.5 Test Requirement
6.5.2.4 EVM equalizer spectrum flatness
6.5.2.4.1 Test Purpose
6.5.2.4.2 Test applicability
6.5.2.4.3 Minimum conformance requirements
6.5.2.4.4 Test description
6.5.2.4.5 Test requirement
6.5.2.4E EVM equalizer spectrum flatness for UE category 0
6.5.2.4E.1 Test Purpose
6.5.2.4E.2 Test applicability
6.5.2.4E.3 Minimum conformance requirements
6.5.2.4E.4 Test description
6.5.2.4E.5 Test requirement
6.5.2.4EA EVM equalizer spectrum flatness for UE category M1
6.5.2.4EA.1 Test Purpose
6.5.2.4EA.2 Test applicability
6.5.2.4EA.3 Minimum conformance requirements
6.5.2.4EA.4 Test description
6.5.2.4EA.5 Test requirement
6.5.2.4EB EVM equalizer spectrum flatness for UE category 1bis
6.5.2.4EB.1 Test purpose
6.5.2.4EB.2 Test applicability
6.5.2.4EB.3 Minimum conformance requirements
6.5.2.4EB.4 Test description
6.5.2.4EB.5 Test requirement
6.5.2.4G EVM equalizer spectrum flatness for V2X transmission
6.5.2.4G.1 EVM equalizer spectrum flatness for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.5.2.4G.1.1 Test Purpose
6.5.2.4G.1.2 Test applicability
6.5.2.4G.1.3 Minimum conformance requirements
6.5.2.4G.1.4 Test description
6.5.2.4G.1.4.1 Initial conditions
6.5.2.4G.1.4.2 Test procedure
6.5.2.4G.1.4.3 Message contents
6.5.2.4G.1.5 Test requirement
6.5.2.4G.3 EVM equalizer spectrum flatness for V2X Communication / Intra-band contiguous multi-carrier operation
6.5.2.4G.3.2 Test Applicability
6.5.2.4G.3.3 Minimum conformance requirements
6.5.2.4G.3.4 Test Description
6.5.2.4G.3.4.1 Initial Conditions
6.5.2.4G.3.4.2 Test Procedure
6.5.2.4G.3.4.3 Message Contents
6.5.2.4G.3.5 Test requirement
6.5.2A Transmit modulation for CA
6.5.2A.1 Error Vector Magnitude (EVM) for CA
6.5.2A.1.0 Minimum conformance requirements
6.5.2A.1.1 Error Vector Magnitude (EVM) for CA (intra-band contiguous DL CA and UL CA)
6.5.2A.1.1_1 EVM for CA (intra-band contiguous DL CA and UL CA) with UL 64QAM
6.5.2A.1.1_2 EVM for CA (intra-band contiguous DL CA and UL CA) with UL 256QAM
6.5.2A.1.2 Error Vector Magnitude (EVM) for CA (inter-band DL CA and UL CA)
6.5.2A.1.2_1 Error Vector Magnitude (EVM) for CA (inter-band DL CA and UL CA) for UL 64QAM
6.5.2A.1.2_2 Error Vector Magnitude (EVM) for CA (inter-band DL CA and UL CA) for UL 256QAM
6.5.2A.1.3 Error Vector Magnitude (EVM) for CA (intra-band non-contiguous DL CA and UL CA)
6.5.2A.1.3_1 Error Vector Magnitude (EVM) for CA (intra-band non-contiguous DL CA and UL CA) for UL 64QAM
6.5.2A.1.3_2 Error Vector Magnitude (EVM) for CA (intra-band non-contiguous DL CA and UL CA) for UL 256QAM
6.5.2A.1.4 Error Vector Magnitude (EVM) for CA (3UL CA)
6.5.2A.2 Carrier leakage for CA
6.5.2A.2.0 Minimum conformance requirements
6.5.2A.2.1 Carrier leakage for CA (intra-band contiguous DL CA and UL CA)
6.5.2A.2.2 Carrier leakage for CA (inter-band DL CA and UL CA)
6.5.2A.2.3 Carrier leakage for CA (intra-band non-contiguous DL CA and UL CA)
6.5.2A.2.4 Carrier leakage for CA (3UL CA)
6.5.2A.3 In-band emissions for non allocated RB for CA
6.5.2A.3.0 Minimum conformance requirements
6.5.2A.3.1 In-band emissions for non allocated RB for CA (intra-band contiguous DL CA and UL CA)
6.5.2A.3.2 In-band emissions for non allocated RB for CA (inter-band DL CA and UL CA)
6.5.2A.3.3 In-band emissions for non allocated RB for CA (intra-band non-contiguous DL CA and UL CA)
6.5.2A.3.4 In-band emissions for non allocated RB for CA (3UL CA)
6.5.2B Transmit modulation for UL- MIMO
6.5.2B.1 Error Vector Magnitude (EVM) for UL- MIMO
6.5.2B.1.1 Test Purpose
6.5.2B.1.2 Test applicability
6.5.2B.1.3 Minimum conformance requirements
6.5.2B.1.4 Test description
6.5.2B.1.5 Test requirement
6.5.2B.2 Carrier leakage for UL-MIMO
6.5.2B.2.1 Test Purpose
6.5.2B.2.2 Test applicability
6.5.2B.2.3 Minimum conformance requirements
6.5.2B.2.4 Test description
6.5.2B.2.5 Test requirement
6.5.2B.3 In-band emissions for non allocated RB for UL-MIMO
6.5.2B.3.1 Test Purpose
6.5.2B.3.2 Test applicability
6.5.2B.3.3 Minimum conformance requirements
6.5.2B.3.4 Test description
6.5.2B.3.5 Test requirement
6.5.2B.4 EVM equalizer spectrum flatness for UL-MIMO
6.5.2B.4.1 Test Purpose
6.5.2B.4.2 Test applicability
6.5.2B.4.3 Minimum conformance requirements
6.5.2B.4.4 Test description
6.5.2B.4.5 Test requirement
6.6 Output RF spectrum emissions
6.6.1 Occupied bandwidth
6.6.1.1 Test purpose
6.6.1.2 Test applicability
6.6.1.3 Minimum conformance requirements
6.6.1.4 Test description
6.6.1.4.1 Initial conditions
6.6.1.4.2 Test procedure
6.6.1.4.3 Message contents
6.6.1.5 Test requirement
6.6.1A Occupied bandwidth for CA
6.6.1A.0 Minimum conformance requirements
6.6.1A.1 Occupied bandwidth for CA (intra-band contiguous DL CA and UL CA)
6.6.1A.1.1 Test purpose
6.6.1A.1.2 Test applicability
6.6.1A.1.3 Minimum conformance requirements
6.6.1A.1.4 Test description
6.6.1A.1.5 Test Requirements
6.6.1A.2 Occupied bandwidth for CA (inter-band DL CA and UL CA)
6.6.1A.2.1 Test purpose
6.6.1A.2.2 Test applicability
6.6.1A.2.3 Minimum conformance requirements
6.6.1A.2.4 Test description
6.6.1A.2.5 Test Requirements
6.6.1A.3 Occupied bandwidth for CA (intra-band non-contiguous DL CA and UL CA)
6.6.1A.3.1 Test purpose
6.6.1A.3.2 Test applicability
6.6.1A.3.3 Minimum conformance requirements
6.6.1A.3.4 Test description
6.6.1A.3.5 Test Requirements
6.6.1A.4 Occupied bandwidth for CA (3DL CA and 3UL CA)
6.6.1A.4.1 Test purpose
6.6.1A.4.2 Test applicability
6.6.1A.4.3 Minimum conformance requirements
6.6.1A.4.4 Test description
6.6.1A.4.5 Test Requirements
6.6.1B Occupied bandwidth for UL-MIMO
6.6.1B.1 Test purpose
6.6.1B.2 Test applicability
6.6.1B.3 Minimum conformance requirements
6.6.1B.4 Test description
6.6.1B.4.1 Initial conditions
6.6.1B.4.2 Test procedure
6.6.1B.4.3 Message contents
6.6.1E Occupied bandwidth for UE category 0
6.6.1E.1 Test purpose
6.6.1E.2 Test applicability
6.6.1E.2 Minimum conformance requirements
6.6.1E.4 Test description
6.6.1E.4.1 Initial conditions
6.6.1E.4.2 Test procedure
6.6.1E.4.3 Message contents
6.6.1E.5 Test requirement
6.6.1EA Occupied bandwidth for UE category M1
6.6.1EA.1 Test purpose
6.6.1EA.2 Test applicability
6.6.1EA.3 Minimum conformance requirements
6.6.1EA.4 Test description
6.6.1E.4A.1 Initial conditions
6.6.1EA.4.2 Test procedure
6.6.1EA.4.3 Message contents
6.6.1EA.5 Test requirement
6.6.1EB Occupied bandwidth for UE category 1bis
6.6.1EB.1 Test purpose
6.6.1EB.2 Test applicability
6.6.1EB.3 Minimum conformance requirements
6.6.1EB.4 Test description
6.6.1EB.4.1 Initial conditions
6.6.1EB.4.2 Test procedure
6.6.1EB.4.3 Message contents
6.6.1EB.5 Test requirement
6.6.1EC Occupied bandwidth for UE category M2
6.6.1EC.1 Test purpose
6.6.1EC.2 Test applicability
6.6.1EC.3 Minimum conformance requirements
6.6.1EC.4 Test description
6.6.1EC.4.1 Initial conditions
6.6.1EC.4.2 Test procedure
6.6.1EC.4.3 Message contents
6.6.1EC.5 Test requirement
6.6.1F Occupied bandwidth for category NB1 and NB2
6.6.1F.1 Test purpose
6.6.1F.2 Test applicability
6.6.1F.3 Minimum conformance requirements
6.6.1F.4 Test description
6.6.1F.4.1 Initial conditions
6.6.1F.4.2 Test procedure
6.6.1F.4.3 Message contents
6.6.1F.5 Test requirement
6.6.1G Occupied bandwidth for V2X Communication
6.6.1G.1 Occupied bandwidth for V2X Communication / Non-concurrent with E-UTRA uplink transmission
6.6.1G.1.1 Test purpose
6.6.1G.1.2 Test applicability
6.6.1G.1.3 Minimum conformance requirements
6.6.1G.1.4 Test description
6.6.1G.1.4.1 Initial conditions
6.6.1G.1.4.2 Test procedure
6.6.1G.1.4.3 Message contents
6.6.1G.1.5 Test requirements
6.6.1G.2 Occupied bandwidth for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
6.6.1G.2.1 Test purpose
6.6.1G.2.2 Test applicability
6.6.1G.2.3 Minimum conformance requirements
6.6.1G.2.4 Test description
6.6.1G.2.4.1 Initial conditions
6.6.1G.2.4.2 Test procedure
6.6.1G.2.4.3 Message contents
6.6.1G.2.5 Test requirements
6.6.1G.3 Occupied bandwidth for V2X Communication / Intra-band contiguous multi-carrier operation
6.6.1G.3.1 Test purpose
6.6.1G.3.2 Test applicability
6.6.1G.3.3 Minimum conformance requirements
6.6.1G.3.4 Test description
6.6.1G.3.4.1 Initial conditions
6.6.1G.3.4.2 Test procedure
6.6.1G.3.4.3 Message contents
6.6.1G.3.5 Test requirements
6.6.2 Out of band emission
6.6.2.1 Spectrum Emission Mask
6.6.2.1.1 Test purpose
6.6.2.1.2 Test applicability
6.6.2.1.3 Minimum conformance requirements
6.6.2.1.4 Test description
6.6.2.1.5 Test requirements
6.6.2.1_1 Spectrum Emission Mask for Multi-Cluster PUSCH
6.6.2.1_1.1 Test purpose
6.6.2.1_1.2 Test applicability
6.6.2.1_1.3 Minimum conformance requirements
6.6.2.1_1.4 Test description
6.6.2.1_1.5 Test requirements
6.6.2.1A Spectrum emission mask for CA
6.6.2.1A.0 Minimum conformance requirements
6.6.2.1A.1 Spectrum emission mask for CA (intra-band contiguous DL CA and UL CA)
6.6.2.1A.2 Spectrum emission mask for CA (inter-band DL CA and UL CA)
6.6.2.1A.3 Spectrum emission mask for CA (intra-band non-contiguous DL CA and UL CA)
6.6.2.1A.4 Spectrum emission mask for CA (3UL CA)
6.6.2.1B Spectrum Emission Mask for UL-MIMO
6.6.2.1B.1 Test purpose
6.6.2.1B.2 Test applicability
6.6.2.1B.3 Minimum conformance requirements
6.6.2.1B.4 Test description
6.6.2.1B.5 Test requirements
6.6.2.1E Spectrum Emission Mask for UE category 0
6.6.2.1E.1 Test purpose
6.6.2.1E.2 Test applicability
6.6.2.1E.3 Minimum conformance requirements
6.6.2.1E.4 Test description
6.6.2.1E.5 Test requirements
6.6.2.1EA Spectrum Emission Mask for UE category M1
6.6.2.1EA.1 Test purpose
6.6.2.1EA.2 Test applicability
6.6.2.1EA.3 Minimum conformance requirements
6.6.2.1EA.4 Test description
6.6.2.1EA.5 Test requirements
6.6.2.1EB Spectrum Emission Mask for UE category 1bis
6.6.2.1EB.1 Test purpose
6.6.2.1EB.2 Test applicability
6.6.2.1EB.3 Minimum conformance requirements
6.6.2.1EB.4 Test description
6.6.2.1EB.5 Test requirements
6.6.2.1EC Spectrum Emission Mask for UE category M2
6.6.2.1EC.1 Test purpose
6.6.2.1EC.2 Test applicability
6.6.2.1EC.3 Minimum conformance requirements
6.6.2.1EC.4 Test description
6.6.2.1EC.5 Test requirements
6.6.2.1F Spectrum Emission Mask for category NB1 and NB2
6.6.2.1F.1 Test purpose
6.6.2.1F.2 Test applicability
6.6.2.1F.3 Minimum conformance requirements
6.6.2.1F.4 Test description
6.6.2.1F.5 Test requirements
6.6.2.1G Spectrum Emission Mask for V2X Communication
6.6.2.1G.1 Spectrum Emission Mask for V2X Communication Non-concurrent with E-UTRA uplink transmissions
6.6.2.1G.1.1 Test purpose
6.6.2.1G.1.2 Test applicability
6.6.2.1G.1.3 Minimum conformance requirements
6.6.2.1G.1.4 Test description
6.6.2.1G.1.4.1 Initial conditions
6.6.2.1G.1.4.2 Test procedure
6.6.2.1G.1.4.3 Message contents
6.6.2.1G.1.5 Test requirements
6.6.2.1G.2 Spectrum Emission Mask for V2X Communication /Sidelink simultaneous with E-UTRA uplink transmissions
6.6.2.1G.2.1 Test purpose
6.6.2.1G.2.2 Test applicability
6.6.2.1G.2.3 Minimum conformance requirements
6.6.2.1G.2.4 Test description
6.6.2.1G.2.5 Test requirements
6.6.2.1G.3 Spectrum Emission Mask for V2X Communication / Intra-band contiguous MCC operation
6.6.2.1G.3.1 Test purpose
6.6.2.1G.3.2 Test Applicability
6.6.2.1G.3.3 Minimum conformance requirements
6.6.2.1G.3.4 Test Description
6.6.2.1G.3.4.1 Initial conditions
6.6.2.1G.3.4.2 Test procedure
6.6.2.1G.3.4.3 Message Contents
6.6.2.1G.3.5 Test Requirement
6.6.2.2 Additional Spectrum Emission Mask
6.6.2.2.1 Test purpose
6.6.2.2.2 Test applicability
6.6.2.2.3 Minimum conformance requirements
6.6.2.2.4 Test description
6.6.2.2.5 Test requirements
6.6.2.2_1 Additional Spectrum Emission Mask for UL 64QAM
6.6.2.2_1.1 Test purpose
6.6.2.2_1.2 Test applicability
6.6.2.2_1.3 Minimum conformance requirements
6.6.2.2_1.4 Test description
6.6.2.2_1.5 Test requirements
6.6.2.2_2 Additional Spectrum Emission Mask with PUSCH frequency hopping
6.6.2.2_2.1 Test purpose
6.6.2.2_2.2 Test applicability
6.6.2.2_2.3 Minimum conformance requirements
6.6.2.2_2.4 Test description
6.6.2.2_2.5 Test requirements
6.6.2.2_2 Additional Spectrum Emission Mask for UL 256QAM
6.6.2.2_2.1 Test purpose
6.6.2.2_2.2 Test applicability
6.6.2.2_2.3 Minimum conformance requirements
6.6.2.2_2.4 Test description
6.6.2.2_2.5 Test requirements
6.6.2.2A Additional Spectrum Emission Mask for CA
6.6.2.2A.1 Additional Spectrum Emission Mask for CA (intra-band contiguous DL CA and UL CA)
6.6.2.2A.1_1 Additional Spectrum Emission Mask for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM
6.6.2.2A.1_2 Additional Spectrum Emission Mask for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM
6.6.2.2A.2 Additional Spectrum Emission Mask for CA (inter-band DL CA and UL CA)
6.6.2.2A.2_1 Additional Spectrum Emission Mask for CA (inter-band DL CA and UL CA) for UL 64QAM
6.6.2.2A.2_2 Additional Spectrum Emission Mask for CA (inter-band DL CA and UL CA) for UL 256QAM
6.6.2.2A.3 Additional Spectrum Emission Mask for CA (intra-band non-contiguous DL CA and UL CA)
6.6.2.2A.4 Additional Spectrum Emission Mask for CA (3UL CA)
6.6.2.2B Additional Spectrum Emission Mask for UL-MIMO
6.6.2.2B.1 Test purpose
6.6.2.2B.2 Test applicability
6.6.2.2B.3 Minimum conformance requirements
6.6.2.2B.4 Test description
6.6.2.2B.5 Test requirements
6.6.2.2E Additional Spectrum Emission Mask for UE category 0
6.6.2.2E.1 Test purpose
6.6.2.2E.2 Test applicability
6.6.2.2E.3 Minimum conformance requirements
6.6.2.2E.4 Test description
6.6.2.2E.5 Test requirements
6.6.2.2EA Additional Spectrum Emission Mask for UE category M1
6.6.2.2EA.1 Test purpose
6.6.2.2EA.2 Test applicability
6.6.2.2EA.3 Minimum conformance requirements
6.6.2.2EA.4 Test description
6.6.2.2EA.5 Test requirements
6.6.2.2EB Additional Spectrum Emission Mask for UE category 1bis
6.6.2.2EB.1 Test purpose
6.6.2.2EB.2 Test applicability
6.6.2.2EB.3 Minimum conformance requirements
6.6.2.2EB.4 Test description
6.6.2.2EB.5 Test requirements
6.6.2.2G Additional Spectrum Emission Mask for V2X Communication
6.6.2.2G.0 Minimum Requirements
6.6.2.2G.1 Additional Spectrum Emission Mask for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.6.2.2G.1.1 Test purpose
6.6.2.2G.1.2 Test applicability
6.6.2.2G.1.3 Minimum conformance requirements
6.6.2.2G.1.4 Test description
6.6.2.2G.1.4.1 Initial conditions
6.6.2.2G.1.4.2 Test procedure
6.6.2.2G.1.4.3 Message contents
6.6.2.2G.1.5 Test requirements
6.6.2.2G.2 Additional Spectrum Emission Mask for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmissions
6.6.2.2G.2.1 Test purpose
6.6.2.2G.2.2 Test applicability
6.6.2.2G.2.3 Minimum conformance requirements
6.6.2.2G.2.4 Test description
6.6.2.2G.2.4.1 Initial conditions
6.6.2.2G.2.4.2 Test procedure
6.6.2.2G.2.4.3 Message contents
6.6.2.2G.2.5 Test requirements
6.6.2.3 Adjacent Channel Leakage power Ratio
6.6.2.3.1 Test purpose
6.6.2.3.2 Test applicability
6.6.2.3.3 Minimum conformance requirements
6.6.2.3.4 Test description
6.6.2.3.5 Test requirement
6.6.2.3_1 Adjacent Channel Leakage power Ratio for HPUE
6.6.2.3_1.1 Test purpose
6.6.2.3_1.2 Test applicability
6.6.2.3_1.3 Minimum conformance requirements
6.6.2.3_1.4 Test description
6.6.2.3_1.5 Test requirement
6.6.2.3_2 Adjacent Channel Leakage power Ratio for Multi-Cluster PUSCH
6.6.2.3_2.1 Test purpose
6.6.2.3_2.2 Test applicability
6.6.2.3_2.3 Minimum conformance requirements
6.6.2.3_2.4 Test description
6.6.2.3_2.5 Test requirement
6.6.2.3_3 Adjacent Channel Leakage power Ratio for UL 64QAM
6.6.2.3_3.1 Test purpose
6.6.2.3_3.2 Test applicability
6.6.2.3_3.3 Minimum conformance requirements
6.6.2.3_3.4 Test description
6.6.2.3_3.5 Test requirement
6.6.2.3_4 Adjacent Channel Leakage power Ratio for Multi-Cluster PUSCH with UL 64QAM
6.6.2.3_4.1 Test purpose
6.6.2.3_4.2 Test applicability
6.6.2.3_4.3 Minimum conformance requirements
6.6.2.3_4.4 Test description
6.6.2.3_4.5 Test requirement
6.6.2.3_5 Adjacent Channel Leakage power Ratio for UL 256QAM
6.6.2.3_5.1 Test purpose
6.6.2.3_5.2 Test applicability
6.6.2.3_5.3 Minimum conformance requirements
6.6.2.3_5.4 Test description
6.6.2.3_5.5 Test requirement
6.6.2.3_6 Adjacent Channel Leakage power Ratio for Multi-Cluster PUSCH with UL 256QAM
6.6.2.3_6.1 Test purpose
6.6.2.3_6.2 Test applicability
6.6.2.3_6.3 Minimum conformance requirements
6.6.2.3_6.4 Test description
6.6.2.3_6.5 Test requirement
6.6.2.3A Adjacent Channel Leakage power Ratio for CA
6.6.2.3A.0 Minimum conformance requirements
6.6.2.3A.0.1 Minimum requirement UTRA for CA
6.6.2.3A.0.2 Minimum requirements for CA E-UTRA
6.6.2.3A.1 Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA)
6.6.2.3A.1_1 Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM
6.6.2.3A.1_2 Adjacent Channel Leakage power Ratio for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM
6.6.2.3A.2 Adjacent Channel Leakage power Ratio for CA (inter-band DL CA and UL CA)
6.6.2.3A.2_1 Adjacent Channel Leakage power Ratio for CA (inter-band DL CA and UL CA) for UL 64QAM
6.6.2.3A.2_2 Adjacent Channel Leakage power Ratio for CA (inter-band DL CA and UL CA) for UL 256QAM
6.6.2.3A.3 Adjacent Channel Leakage power Ratio for CA (intra-band non-contiguous DL CA and UL CA)
6.6.2.3A.3.1 Test purpose
6.6.2.3A.3_1 Adjacent Channel Leakage power Ratio for CA (intra-band non-contiguous DL CA and UL CA) for UL 64QAM
6.6.2.3A.3_1.1 Test purpose
6.6.2.3A.3_1.2 Test applicability
6.6.2.3A.3_1.3 Minimum conformance requirements
6.6.2.3A.3_1.4 Test description
6.6.2.3A.3_1.4.1 Initial condition
6.6.2.3A.3_1.4.3 Message contents
6.6.2.3A.3_1.5 Test Requirements
6.6.2.3A.3.2 Test applicability
6.6.2.3A.3.3 Minimum conformance requirements
6.6.2.3A.3_2 Adjacent Channel Leakage power Ratio for CA (intra-band non-contiguous DL CA and UL CA) for UL 256QAM
6.6.2.3A.3_2.1 Test purpose
6.6.2.3A.3_2.2 Test applicability
6.6.2.3A.3_2.3 Minimum conformance requirements
6.6.2.3A.3_2.4 Test description
6.6.2.3A.3_2.4.1 Initial condition
6.6.2.3A.3_2.4.3 Message contents
6.6.2.3A.3_2.5 Test Requirements
Same as in clause 6.6.2.3A.3_1.5.6.6.2.3A.3.4 Test description
6.6.2.3A.3.4.1 Initial condition
6.6.2.3A.3.4.3 Message contents
6.6.2.3A.3.5 Test Requirements
6.6.2.3A.3.5.1 Test requirements E-UTRA
6.6.2.3A.4.1 Test purpose
6.6.2.3A.4.2 Test applicability
6.6.2.3A.4.3 Minimum conformance requirements
6.6.2.3A.4.4 Test description
6.6.2.3A.4.4.1 Initial conditions
6.6.2.3A.4.4.2 Test procedure
6.6.2.3A.4.4.3 Message contents
6.6.2.3A.4.5 Test Requirements
6.6.2.3B Adjacent Channel Leakage power Ratio for UL-MIMO
6.6.2.3B.1 Test purpose
6.6.2.3B.2 Test applicability
6.6.2.3B.3 Minimum conformance requirements
6.6.2.3B.4 Test description
6.6.2.3B.5 Test requirement
6.6.2.3E Adjacent Channel Leakage power Ratio for UE category 0
6.6.2.3E.1 Test purpose
6.6.2.3E.2 Test applicability
6.6.2.3E.3 Minimum conformance requirements
6.6.2.3E.4 Test description
6.6.2.3E.5 Test requirement
6.6.2.3EA Adjacent Channel Leakage power Ratio for UE category M1
6.6.2.3EA.1 Test purpose
6.6.2.3EA.2 Test applicability
6.6.2.3EA.3 Minimum conformance requirements
6.6.2.3EA.4 Test description
6.6.2.3EA.5 Test requirement
6.6.2.3EB Adjacent Channel Leakage power Ratio for UE category 1bis
6.6.2.3EB.1 Test purpose
6.6.2.3EB.2 Test applicability
6.6.2.3EB.3 Minimum conformance requirements
6.6.2.3EB.4 Test description
6.6.2.3EB.5 Test requirement
6.6.2.3EC Adjacent Channel Leakage power Ratio for UE category M2
6.6.2.3EC.1 Test purpose
6.6.2.3EC.2 Test applicability
6.6.2.3EC.3 Minimum conformance requirements
6.6.2.3EC.4 Test description
6.6.2.3EC.5 Test requirement
6.6.2.3F Adjacent Channel Leakage power Ratio for category NB1 and NB2
6.6.2.3F.1 Test purpose
6.6.2.3F.2 Test applicability
6.6.2.3F.3 Minimum conformance requirements
6.6.2.3F.4 Test description
6.6.2.3F.5 Test requirement
6.6.2.3G Adjacent Channel Leakage power Ratio for V2X Communication
6.6.2.3G.1 Adjacent Channel Leakage power Ratio for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.6.2.3G.1.1 Test purpose
6.6.2.3G.1.2 Test applicability
6.6.2.3G.1.3 Minimum conformance requirements
6.6.2.3G.1.4 Test description
6.6.2.3G.1.4.1 Initial conditions
6.6.2.3G.1.4.2 Test procedure
6.6.2.3G.1.4.3 Message contents
6.6.2.3G.1.5 Test requirements
6.6.2.3G.2 Adjacent Channel Leakage power Ratio for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink tran
6.6.2.3G.2.1 Test purpose
6.6.2.3G.2.2 Test applicability
6.6.2.3G.2.3 Minimum conformance requirements
6.6.2.3G.2.4 Test description
6.6.2.3G.2.4.1 Initial conditions
6.6.2.3G.2.4.2 Test procedure
6.6.2.3G.2.4.3 Message contents
6.6.2.3G.2.5 Test requirements
6.6.2.4 Void
6.6.3 Spurious emissions
6.6.3.1 Transmitter Spurious emissions
6.6.3.1.1 Test purpose
6.6.3.1.2 Test applicability
6.6.3.1.3 Minimum conformance requirements
6.6.3.1.4 Test description
6.6.3.1.5 Test requirement
6.6.3.1_1 Transmitter Spurious emissions for Multi-Cluster PUSCH
6.6.3.1_1.1 Test purpose
6.6.3.1_1.2 Test applicability
6.6.3.1_1.3 Minimum conformance requirements
6.6.3.1_1.4 Test description
6.6.3.1_1.5 Test requirement
6.6.3.1A Transmitter Spurious emissions for CA
6.6.3.1A.0 Minimum conformance requirements
6.6.3.1A.1 Transmitter Spurious emissions for CA (intra-band contiguous DL CA and UL CA)
6.6.3.1A.2 Transmitter Spurious emissions for CA (inter-band DL CA and UL CA)
6.6.3.1A.3 Transmitter Spurious emissions for CA (intra-band non-contiguous DL CA and UL CA)
6.6.3.1A.4 Transmitter Spurious emissions for CA (3UL CA)
6.6.3.1A.4.1 Transmitter Spurious emissions for CA (intra-band contiguous 3DL CA and 3UL CA)
6.6.3.1A.4.1.1 Test purpose
6.6.3.1A.4.1.2 Test applicability
6.6.3.1A.4.1.3 Minimum conformance requirements
6.6.3.1A.4.1.4 Test description
6.6.3.1A.4.1.4.1 Initial conditions
6.6.3.1A.4.1.4.2 Test procedure
6.6.3.1A.4.1.4.3 Message contents
6.6.3.1A.4.1.5 Test Requirements
6.6.3.1A.4.2 Transmitter Spurious emissions for CA (inter-band 3DL CA and 3UL CA)
6.6.3.1A.4.2.1 Test purpose
6.6.3.1A.4.2.2 Test applicability
6.6.3.1A.4.2.3 Minimum conformance requirements
6.6.3.1A.4.2.4 Test description
6.6.3.1A.4.2.4.1 Initial conditions
6.6.3.1A.4.2.4.2 Test procedure
6.6.3.1A.4.2.4.3 Message contents
6.6.3.1A.4.2.5 Test Requirements
6.6.3.1A.4.3 Transmitter Spurious emissions for CA (3UL CA) (intra-band non-contiguous 3DL CA and 3UL CA)
6.6.3.1A.4.3.1 Test purpose
6.6.3.1A.4.3.2 Test applicability
6.6.3.1A.4.3.3 Minimum conformance requirements
6.6.3.1A.4.3.4 Test description
6.6.3.1A.4.3.4.1 Initial conditions
6.6.3.1A.4.3.4.2 Test procedure
6.6.3.1A.4.3.4.3 Message contents
6.6.3.1A.4.3.5 Test requirement
6.6.3.2 Spurious emission band UE co-existence
6.6.3.2.1 Test purpose
6.6.3.2.2 Test applicability
6.6.3.2.3 Minimum conformance requirements
6.6.3.2.4 Test description
6.6.3.2.5 Test requirement
6.6.3.2_1 Void
6.6.3.2A Spurious emission band UE co-existence for CA
6.6.3.2A.0 Minimum conformance requirements
6.6.3.2A.1 Spurious emission band UE co-existence for CA (intra-band contiguous DL CA and UL CA)
6.6.3.2A.2 Spurious emission band UE co-existence for CA (inter-band DL CA and UL CA)
6.6.3.2A.3 Spurious emission band UE co-existence for CA (intra-band non-contiguous DL CA and UL CA)
6.6.3.2A.4 Spurious emission band UE co-existence for CA (3UL CA)
6.6.3.3 Additional spurious emissions
6.6.3.3.1 Test purpose
6.6.3.3.2 Test applicability
6.6.3.3.3 Minimum conformance requirements
6.6.3.3.4 Test description
6.6.3.3.5 Test requirement
6.6.3.3_1 Additional spurious emissions for UL 64QAM
6.6.3.3_1.1 Test purpose
6.6.3.3_1.2 Test applicability
6.6.3.3_1.3 Minimum conformance requirements
6.6.3.3_1.4 Test description
6.6.3.3_1.5 Test requirement
6.6.3.3_2 Additional spurious emissions for UL 256QAM
6.6.3.3_2.1 Test purpose
6.6.3.3_2.2 Test applicability
6.6.3.3_2.3 Minimum conformance requirements
6.6.3.3_2.4 Test description
6.6.3.3_2.5 Test requirement
6.6.3.3A Additional spurious emissions for CA
6.6.3.3A.1 Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA)
6.6.3.3A.1_1 Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA) for UL 64QAM
6.6.3.3A.1_2 Additional spurious emissions for CA (intra-band contiguous DL CA and UL CA) for UL 256QAM
6.6.3.3A.2 Additional spurious emissions for CA (inter-band DL CA and UL CA)
6.6.3.3A.2_1 Additional spurious emissions for CA (inter-band DL CA and UL CA) for UL 64QAM
6.6.3.3A.2_2 Additional spurious emissions for CA (inter-band DL CA and UL CA) for UL 256QAM
Same test requirements as in clause 6.6.3.3A.2.5.6.6.3.3A.3 Additional spurious emissions for CA (intra-band non-contiguous DL
6.6.3B Spurious emission for UL-MIMO
6.6.3B.1 Transmitter Spurious emissions for UL-MIMO
6.6.3B.1.1 Test purpose
6.6.3B.1.2 Test applicability
6.6.3B.1.3 Minimum conformance requirements
6.6.3B.1.4 Test description
6.6.3B.1.5 Test requirement
6.6.3B.2 Spurious emission band UE co-existence for UL-MIMO
6.6.3B.2.1 Test purpose
6.6.3B.2.2 Test applicability
6.6.3B.2.3 Minimum conformance requirements
6.6.3B.2.4 Test description
6.6.3B.2.5 Test requirement
6.6.3B.3 Additional spurious emissions for UL-MIMO
6.6.3B.3.1 Test purpose
6.6.3B.3.2 Test applicability
6.6.3B.3.3 Minimum conformance requirements
6.6.3B.3.4 Test description
6.6.3B.3.5 Test requirement
6.6.3E Spurious emission for UE category 0
6.6.3E.1 Transmitter Spurious emissions for UE category 0
6.6.3E.1.1 Test purpose
6.6.3E.1.2 Test applicability
6.6.3E.1.3 Minimum conformance requirements
6.6.3E.1.4 Test description
6.6.3E.1.5 Test requirement
6.6.3E.2 Spurious emission band UE co-existence for UE category 0
6.6.3E.2.1 Test purpose
6.6.3E.2.2 Test applicability
6.6.3E.2.3 Minimum conformance requirements
6.6.3E.2.4 Test description
6.6.3E.2.5 Test requirement
6.6.3E.3 Additional spurious emissions for UE category 0
6.6.3E.3.1 Test purpose
6.6.3E.3.2 Test applicability
6.6.3E.3.3 Minimum conformance requirements
6.6.3E.3.4 Test description
6.6.3E.3.5 Test requirement
6.6.3EA Spurious emission for UE category M1
6.6.3EA.1 Transmitter Spurious emissions for UE category M1
6.6.3EA.1.1 Test purpose
6.6.3EA.1.2 Test applicability
6.6.3EA.1.3 Minimum conformance requirements
6.6.3EA.1.4 Test description
6.6.3EA.1.5 Test requirement
6.6.3EA.2 Spurious emission band UE co-existence for UE category M1
6.6.3EA.2.1 Test purpose
6.6.3EA.2.2 Test applicability
6.6.3EA.2.3 Minimum conformance requirements
6.6.3EA.2.4 Test description
6.6.3EA.2.5 Test requirement
6.6.3EA.3 Additional spurious emissions for UE category M1
6.6.3EA.3.1 Test purpose
6.6.3EA.3.2 Test applicability
6.6.3EA.3.3 Minimum conformance requirements
6.6.3EA.3.4 Test description
6.6.3EA.3.5 Test requirement
6.6.3EB Spurious emission for UE category 1bis
6.6.3EB.1 Transmitter Spurious emissions for UE category 1bis
6.6.3EB.1.1 Test purpose
6.6.3EB.1.2 Test applicability
6.6.3EB.1.3 Minimum conformance requirements
6.6.3EB.1.4 Test description
6.6.3EB.1.5 Test requirement
6.6.3EB.2 Spurious emission band UE co-existence for UE category 1bis
6.6.3EB.2.1 Test purpose
6.6.3EB.2.2 Test applicability
6.6.3EB.2.3 Minimum conformance requirements
6.6.3EB.2.4 Test description
6.6.3EB.2.5 Test requirement
6.6.3EB.3 Additional spurious emissions for UE category 1bis
6.6.3EB.3.1 Test purpose
6.6.3EB.3.2 Test applicability
6.6.3EB.3.3 Minimum conformance requirements
6.6.3EB.3.4 Test description
6.6.3E.3.5 Test requirement
6.6.3EC Spurious emission for UE category M2
6.6.3EC.1 Transmitter Spurious emissions for UE category M2
6.6.3EC.1.1 Test purpose
6.6.3EC.1.2 Test applicability
6.6.3EC.1.3 Minimum conformance requirements
6.6.3EC.1.4 Test description
6.6.3EC.1.5 Test requirement
6.6.3EC.2 Spurious emission band UE co-existence for UE category M2
6.6.3EC.2.1 Test purpose
6.6.3EC.2.2 Test applicability
6.6.3EC.2.3 Minimum conformance requirements
6.6.3EC.2.4 Test description
6.6.3EC.2.5 Test requirement
6.6.3F Spurious emission for category NB1 and NB2
6.6.3F.1 Transmitter Spurious emissions for category NB1 and NB2
6.6.3F.1.1 Test purpose
6.6.3F.1.2 Test applicability
6.6.3F.1.3 Minimum conformance requirements
6.6.3F.1.4 Test description
6.6.3F.1.5 Test requirement
6.6.3F.2 Spurious emission band UE co-existence for category NB1 and NB2
6.6.3F.2.1 Test purpose
6.6.3F.2.2 Test applicability
6.6.3F.2.3 Minimum conformance requirements
6.6.3F.2.4 Test description
6.6.3F.2.5 Test requirement
6.6.3G Transmitter Spurious emissions for V2X
6.6.3G.1 Transmitter Spurious emissions for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.6.3G.1.1 Test purpose
6.6.3G.1.2 Test applicability
6.6.3G.1.3 Minimum conformance requirements
6.6.3G.1.4 Test description
6.6.3G.1.4.1 Initial conditions
6.6.3G.1.4.2 Test procedure
6.6.3G.1.4.3 Message contents
6.6.3G.1.5 Test requirement
6.6.3G.1_1 Spurious emission band UE co-existence for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.6.3G.1_1.1 Test purpose
6.6.3G.1_1.2 Test applicability
6.6.3G.1_1.3 Minimum conformance requirements
6.6.3G.1_1.4 Test description
6.6.3G.1_1.4.1 Initial conditions
6.6.3G.1_1.4.2 Test procedure
6.6.3G.1_1.4.3 Message contents
6.6.3G.1_1.5 Test requirement
6.6.3G.2 Spurious emission for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmissions
6.6.3G.2.1 Test purpose
6.6.3G.2.2 Test applicability
6.6.3G.2.3 Minimum conformance requirements
6.6.3G.2.4 Test description
6.6.3G.2.4.1 Initial conditions
6.6.3G.2.4.2 Test procedure
6.6.3G.2.4.3 Message contents
6.6.3G.2.5 Test requirement
6.6.3G.2_1 Spurious emission band UE co-existence for V2X Communication / Sidelink simultaneous with E-UTRA uplink transmission
6.6.3G.2_1.1 Test purpose
6.6.3G.2_1.2 Test applicability
6.6.3G.2_1.3 Minimum conformance requirements
6.6.3G.2_1.4 Test description
6.6.3G.2_1.4.1 Initial conditions
6.6.3G.2_1.4.2 Test procedure
6.6.3G.2_1.4.3 Message contents
6.6.3G.2_1.5 Test requirement
6.6.3G.2_2 Additional Spurious emission band UE co-existence for V2X Communication / Sidelink simultaneous with E-UTRA uplink t
6.6.3G.3 Spurious emission for V2X Communication / Intra-band contiguous MCC operation
6.6.3G.3.1 Test purpose
6.6.3G.3.2 Test applicability
6.6.3G.3.3 Minimum conformance requirements
6.6.3G.3.4 Test description
6.6.3G.3.4.1 Initial conditions
6.6.3G.3.4.2 Test procedure
6.6.3G.3.4.3 Message contents
6.6.3G.3.5 Test requirement
6.6.3G.3_1 Spurious emission band UE co-existence for V2X Communication / Intra-band contiguous MCC operation
6.6.3G.3_1.1 Test purpose
6.6.3G.3_1.2 Test Applicability
6.6.3G.3_1.3 Minimum conformance requirements
6.6.3G.3_1.4 Test Description
6.6.3G.3_1.4.1 Initial conditions
6.6.3G.3_1.4.2 Test procedure
6.6.3G.3_1.4.3 Message contents
6.6.3G.3_1.5 Test requirement
6.7 Transmit intermodulation
6.7.1 Test purpose
6.7.2 Test applicability
6.7.3 Minimum conformance requirements
6.7.4 Test description
6.7.4.1 Initial conditions
6.7.4.3 Test procedure
6.7.4.3 Message contents
6.7.5 Test requirement
6.7A Transmit intermodulation for CA
6.7A.0 Minimum conformance requirements
6.7A.1 Transmit intermodulation for CA (intra-band contiguous DL CA and UL CA)
6.7A.1.1 Test purpose
6.7A.1.2 Test applicability
6.7A.1.3 Minimum conformance requirements
6.7A.1.4 Test description
6.7A.1.4.1 Initial conditions
6.7A.1.4.2 Test procedure
6.7A.1.4.3 Message contents
6.7A.1.5 Test requirement
6.7A.2 Transmit intermodulation for CA (inter-band DL CA and UL CA)
6.7A.2.1 Test purpose
6.7A.2.2 Test applicability
6.7A.2.3 Minimum conformance requirements
6.7A.2.4 Test description
6.7A.2.4.1 Initial conditions
6.7A.2.4.2 Test procedure
6.7A.2.4.3 Message contents
6.7A.2.5 Test requirement
6.7A.3
6.7A.4 Transmit intermodulation for CA (3DL CA and 3UL CA)
6.7A.4.1 Test purpose
6.7A.4.2 Test applicability
6.7A.4.3 Minimum conformance requirements
6.7A.4.4 Test description
6.7A.4.4.1 Initial conditions
6.7A.4.4.2 Test procedure
6.7A.4.4.3 Message contents
6.7A.4.5 Test requirement
6.7B Transmit intermodulation for UL-MIMO
6.7B.1 Test purpose
6.7B.2 Test applicability
6.7B.3 Minimum conformance requirements
6.7B.4 Test description
6.7B.4.1 Initial conditions
6.7B.4.2 Test procedure
6.7B.4.3 Message contents
6.7E Transmit intermodulation for UE category 0
6.7E.1 Test purpose
6.7E.2 Test applicability
6.7E.3 Minimum conformance requirements
6.7E.4 Test description
6.7E.4.1 Initial conditions
6.7E.4.2 Test procedure
6.7E.4.3 Message contents
6.7E.5 Test requirement
6.7EA Transmit intermodulation for UE category M1
6.7EA.1 Test purpose
6.7EA.2 Test applicability
6.7EA.3 Minimum conformance requirements
6.7EA.4 Test description
6.7EA.4.1 Initial conditions
6.7EA.4.2 Test procedure
6.7EA.4.3 Message contents
6.7EA.5 Test requirement
6.7EB Transmit intermodulation for UE category 1bis
6.7EB.1 Test purpose
6.7EB.2 Test applicability
6.7EB.3 Minimum conformance requirements
6.7EB.4 Test description
6.7EB.4.1 Initial conditions
6.7EB.4.2 Test procedure
6.7EB.4.3 Message contents
6.7EB.5 Test requirement
6.7EC Transmit intermodulation for UE category M2
6.7EC.1 Test purpose
6.7EC.2 Test applicability
6.7EC.3 Minimum conformance requirements
6.7EC.4 Test description
6.7EC.4.1 Initial conditions
6.7EC.4.2 Test procedure
6.7EC.4.3 Message contents
6.7EC.5 Test requirement
6.7F Transmit intermodulation for category NB1 and NB2
6.7F.1 Test purpose
6.7F.2 Test applicability
6.7F.3 Minimum conformance requirements
6.7F.4 Test description
6.7F.4.1 Initial conditions
6.7F.4.3 Test procedure
6.7F.4.3 Message contents
6.7F.5 Test requirement
6.7G Transmit intermodulation for V2X Communication
6.7G.1 Transmit intermodulation for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
6.7G.1.1 Test purpose
6.7G.1.2 Test applicability
6.7G.1.3 Minimum conformance requirements
6.7G.1.4 Test description
6.7G.1.4.1 Initial conditions
6.7G.1.4.2 Test procedure
6.7G.1.4.3 Message contents
6.7G.1.5 Test requirements
6.7G.2 Transmit intermodulation for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
6.7G.2.1 Test purpose
6.7G.2.2 Test applicability
6.7G.2.3 Minimum conformance requirements
6.7G.2.4 Test description
6.7G.2.4.1 Initial conditions
6.7G.2.4.2 Test procedure
6.7G.2.4.3 Message contents
6.7G.2.5 Test requirements
6.7G.3 Transmit intermodulation for V2X Communication / Intra-band contiguous multi-carrier operation
6.7G.3.1 Test purpose
6.7G.3.2 Test applicability.
6.7G.3.3 Minimum conformance requirements
6.7G.3.4 Test description
6.7G.3.4.1 Initial conditions
6.7G.3.4.2 Test procedure
6.7G.3.4.3 Message contents
6.7G.3.5 Test requirement
6.8 Time alignment
6.8.1 Void
6.8A Void
6.8B Time alignment error for UL-MIMO
6.8B.1 Test purpose
6.8B.2 Test applicability
6.8B.3 Minimum conformance requirements
6.8B.4 Test description
6.8B.4.1 Initial condition
6.8B.4.2 Test procedure
6.8B.4.3 Message contents
6.8B.5 Test requirements
7 Receiver Characteristics
7.1 General
7.2 Diversity characteristics
7.3 Reference sensitivity level
7.3.1 Test purpose
7.3.2 Test applicability
7.3.3 Minimum conformance requirements
7.3.4 Test description
7.3.4.1 Initial conditions
7.3.4.2 Test procedure
7.3.4.3 Message contents
7.3.5 Test requirement
7.3_1 Reference sensitivity level with 4 Rx antenna ports
7.3_1.1 Test purpose
7.3_1.2 Test applicability
7.3_1.3 Minimum conformance requirements
7.3_1.4 Test description
7.3_1.4.1 Initial conditions
7.3_1.4.2 Test procedure
7.3_1.4.3 Message contents
7.3_1.5 Test requirement
7.3A Reference sensitivity level for CA
7.3A.0 Minimum conformance requirements
7.3A.1 Reference sensitivity level for CA (intra-band contiguous DL CA and UL CA)
7.3A.1.1 Test purpose
7.3A.1.2 Test applicability
7.3A.1.3 Minimum conformance requirements
7.3A.1.4 Test description
7.3A.1.4.1 Initial conditions
7.3A.1.4.2 Test procedure
7.3A.1.4.3 Message contents
7.3A.1.5 Test requirement
7.3A.2 Reference sensitivity level for CA (intra-band contiguous DL CA without UL CA)
7.3A.2.1 Test purpose
7.3A.2.2 Test applicability
7.3A.2.3 Minimum conformance requirements
7.3A.2.4 Test description
7.3A.2.4.1 Initial conditions
7.3A.2.4.2 Test procedure
7.3A.2.4.3 Message contents
7.3A.2.5 Test requirement
7.3A.3 Reference sensitivity level for CA (inter-band DL CA without UL CA)
7.3A.3.1 Test purpose
7.3A.3.2 Test applicability
7.3A.3.3 Minimum conformance requirements
7.3A.3.4 Test description
7.3A.3.4.1 Initial conditions
7.3A.3.4.2 Test procedure
7.3A.3.4.3 Message contents
7.3A.3.5 Test requirement
7.3A.4 Reference sensitivity level for CA (intra-band non-contiguous DL CA without UL CA)
7.3A.4.1 Test purpose
7.3A.4.2 Test applicability
7.3A.4.3 Minimum conformance requirements
7.3A.4.4 Test description
7.3A.4.4.1 Initial conditions
7.3A.4.4.2 Test procedure
7.3A.4.4.3 Message contents
7.3A.4.5 Test requirement
7.3A.5 Reference sensitivity level for 3DL CA
7.3A.5.1 Test purpose
7.3A.5.2 Test applicability
7.3A.5.3 Minimum conformance requirements
7.3A.5.4 Test description
7.3A.5.4.1 Initial conditions
7.3A.5.4.2 Test procedure
7.3A.5.4.3 Message contents
7.3A.5.5 Test requirement
7.3A.6 Reference sensitivity level for CA (inter-band DL CA and UL CA)
7.3A.6.1 Test purpose
7.3A.6.2 Test applicability
7.3A.6.3 Minimum conformance requirements
7.3A.6.4 Test description
7.3A.6.4.1 Initial conditions
7.3A.6.4.2 Test procedure
7.3A.6.4.3 Message contents
7.3A.6.5 Test requirement
7.3A.7 Reference sensitivity level for CA (intra-band non-contiguous DL CA and UL CA)
7.3A.7.1 Test purpose
7.3A.7.2 Test applicability
7.3A.7.3 Minimum conformance requirements
7.3A.7.4 Test description
7.3A.7.4.1 Initial conditions
7.3A.7.4.2 Test procedure
7.3A.7.4.3 Message contents
7.3A.7.5 Test requirement
7.3A.8
7.3A.9 Reference sensitivity level for 4DL CA
7.3A.9.1 Test purpose
7.3A.9.2 Test applicability
7.3A.9.3 Minimum conformance requirements
7.3A.9.4 Test description
7.3A.9.4.1 Initial conditions
7.3A.9.4.2 Test procedure
7.3A.9.4.3 Message contents
7.3A.9.5 Test requirement
7.3A.10 Reference sensitivity level for 5DL CA
7.3A.10.1 Test purpose
7.3A.10.2 Test applicability
7.3A.10.3 Minimum conformance requirements
7.3A.10.4 Test description
7.3A.10.4.1 Initial conditions
7.3A.10.4.2 Test procedure
7.3A.10.4.3 Message contents
7.3A.10.5 Test requirement
7.3B Reference sensitivity level for UL-MIMO
7.3B.1 Test purpose
7.3B.2 Test applicability
7.3B.3 Minimum conformance requirements
7.3B.4 Test description
7.3B.4.1 Initial conditions
7.3B.4.2 Test procedure
7.3B.4.3 Message contents
7.3B.4.3.1 Message contents exceptions (network signalled value "NS_01")
7.3B.4.3.2 Message contents exceptions (network signalled value "NS_03")
7.3B.4.3.3 Message contents exceptions (network signalled value "NS_06")
7.3B.4.3.4 Message contents exceptions (network signalled value "NS_[09]")
7.3B.5 Test requirement
7.3C
7.3D Reference sensitivity level for ProSe
7.3D.0 Minimum requirements (QPSK) for ProSe
7.3D.1 Reference sensitivity level for ProSe Direct Discovery
7.3D.1.1 Test purpose
7.3D.1.2 Test applicability
7.3D.1.3 Minimum conformance requirements
7.3D.1.4 Test description
7.3D.1.4.1 Initial conditions
7.3D.1.4.2 Test procedure
7.3D.1.4.3 Message contents
7.3D.1.5 Test requirements
7.3D.2 Reference sensitivity level for ProSe Direct Communication
7.3D.2.1 Test purpose
7.3D.2.2 Test applicability
7.3D.2.3 Minimum conformance requirements
7.3D.2.4 Test description
7.3D.2.4.1 Initial conditions
7.3D.2.4.2 Test procedure
7.3D.2.4.3 Message contents
7.3D.2.5 Test requirements
7.3EA Reference sensitivity level for UE category M1
7.3EA.1 Test purpose
7.3EA.2 Test applicability
7.3EA.3 Minimum conformance requirements
7.3EA.4 Test description
7.3EA.4.1 Initial conditions
7.3EA.4.2 Test procedure
7.3EA.4.3 Message contents
7.3EA.4.3.1 Message contents exceptions (network signalled value "NS_01")
7.3EA.4.3.2 Message contents exceptions (network signalled value "NS_03")
7.3EA.4.3.3 Message contents exceptions (network signalled value "NS_06")
7.3EA.4.3.4 Message contents exceptions (network signalled value "NS_09")
7.3EA.4.3.5 Message contents exceptions (network signalled value "NS_08")
7.3EA.5 Test requirement
7.3EB Reference sensitivity level for UE category 1bis
7.3EB.1 Test purpose
7.3EB.2 Test applicability
7.3EB.3 Minimum conformance requirements
7.3EB.4 Test description
7.3EB.4.1 Initial conditions
7.3EB.4.2 Test procedure
7.3EB.4.3 Message contents
7.3EB.5 Test requirement
7.3EC Reference sensitivity level for UE category M2
7.3EC.1 Test purpose
7.3EC.2 Test applicability
7.3EC.3 Minimum conformance requirements
7.3EC.4 Test description
7.3EC.4.1 Initial conditions
7.3EC.4.2 Test procedure
7.3EC.4.3 Message contents
7.3EC.5 Test requirement
7.3F Reference sensitivity level for category NB1 and NB2
7.3F.1 Reference sensitivity level without repetitions for category NB1 and NB2
7.3F.1.1 Test purpose
7.3F.1.2 Test applicability
7.3F.1.3 Minimum conformance requirements
7.3F.1.4 Test description
7.3F.1.4.1 Initial conditions
7.3F.1.4.2 Test Procedure
7.3F.1.4.3 Message contents
7.3F.1.5 Test requirement
7.3F.2 Void
7.3G Reference sensitivity level for V2X Communication
7.3G.0 Minimum conformance requirements
7.3G.1 Reference sensitivity level for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.3G.1.1 Test purpose
7.3G.1.2 Test applicability
7.3G.1.3 Minimum conformance requirements
7.3G.1.4 Test description
7.3G.1.4.1 Initial conditions
7.3G.1.4.2 Test procedure
7.3G.1.4.3 Message contents
7.3G.1.5 Test requirements
7.3G.2 Reference sensitivity level for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.3G.2.1 Test purpose
7.3G.2.2 Test applicability
7.3G.2.3 Minimum conformance requirements
7.3G.2.4 Test description
7.3G.2.4.1 Initial conditions
7.3G.2.4.2 Test procedure
7.3G.2.4.3 Message contents
7.3G.2.5 Test requirements
7.3G.3 Reference sensitivity level for V2X Communication / Intra-band contiguous multi-carrier operation
7.3G.3.1 Test purpose
7.3G.3.2 Test applicability
7.3G.3.3 Minimum conformance requirements
7.3G.3.4.1 Initial conditions
7.3G.3.4.2 Test procedure
7.3G.3.4.3 Message contents
7.3G.3.5 Test requirements
7.4 Maximum input level
7.4.1 Test purpose
7.4.2 Test applicability
7.4.3 Minimum conformance requirements
7.4.4 Test description
7.4.4.1 Initial conditions
7.4.4.2 Test procedure
7.4.4.3 Message contents
7.4.5 Test requirement
7.4_1 Maximum input level with 4 Rx antenna ports
7.4_1.1 Test purpose
7.4_1.2 Test applicability
7.4_1.3 Minimum conformance requirements
7.4_1.4 Test description
7.4_1.4.1 Initial conditions
7.4_1.4.2 Test procedure
7.4_1.4.3 Message contents
7.4_1.5 Test requirement
7.4_H Maximum input level for 256QAM in DL
7.4_H.1 Test purpose
7.4_H.2 Test applicability
7.4_H.3 Minimum conformance requirements
7.4_H.4 Test description
7.4_H.4.1 Initial conditions
7.4_H.4.2 Test procedure
7.4_H.4.3 Message contents
7.4_H.5 Test requirement
7.4A Maximum input level for CA
7.4A.1 Maximum input level for CA (intra-band contiguous DL CA and UL CA)
7.4A.1.1 Test purpose
7.4A.1.2 Test applicability
7.4A.1.3 Minimum conformance requirements
7.4A.1.4 Test description
7.4A.1.4.1 Initial conditions
7.4A.1.4.2 Test procedure
7.4A.1.4.3 Message contents
7.4A.1.5 Test requirement
7.4A.1_H Maximum input level for CA (intra-band contiguous DL CA and UL CA) for 256QAM in DL
7.4A.1_H.1 Test purpose
7.4A.1_H.2 Test applicability
7.4A.1_H.3 Minimum conformance requirements
7.4A.1_H.4 Test description
7.4A.1_H.4.1 Initial conditions
7.4A.1_H.4.2 Test procedure
7.4A.1_H.4.3 Message contents
7.4A.1_H.5 Test requirement
7.4A.2 Maximum input level for CA (intra-band contiguous DL CA without UL CA)
7.4A.2.1 Test purpose
7.4A.2.2 Test applicability
7.4A.2.3 Minimum conformance requirements
7.4A.2.4 Test description
7.4A.2.4.1 Initial conditions
7.4A.2.4.2 Test procedure
7.4A.2.4.3 Message contents
7.4A.2.5 Test requirement
7.4A.2_H Maximum input level for CA (intra-band contiguous DL CA without UL CA) for 256QAM in DL
7.4A.2_H.1 Test purpose
7.4A.2_H.2 Test applicability
7.4A.2_H.3 Minimum conformance requirements
7.4A.2_H.4 Test description
7.4A.2_H.4.1 Initial conditions
7.4A.2_H.4.2 Test procedure
7.4A.2_H.4.3 Message contents
7.4A.2_H.5 Test requirement
7.4A.3 Maximum input level for CA (inter-band DL CA without UL CA)
7.4A.3.1 Test purpose
7.4A.3.2 Test applicability
7.4A.3.3 Minimum conformance requirements
7.4A.3.4 Test description
7.4A.3.4.1 Initial conditions
7.4A.3.4.2 Test procedure
7.4A.3.4.3 Message contents
7.4A.3.5 Test requirement
7.4A.3_H Maximum input level for CA (inter-band DL CA without UL CA) for 256QAM in DL
7.4A.3_H.1 Test purpose
7.4A.3_H.2 Test applicability
7.4A.3_H.3 Minimum conformance requirements
7.4A.3_H.4 Test description
7.4A.3_H.4.1 Initial conditions
7.4A.3_H.4.2 Test procedure
7.4A.3_H.4.3 Message contents
7.4A.3_H.5 Test requirement
7.4A.4 Maximum input level for CA (intra band non-contiguous DL CA without UL CA)
7.4A.4.1 Test purpose
7.4A.4.2 Test applicability
7.4A.4.3 Minimum conformance requirements
7.4A.4.4 Test description
7.4A.4.4.1 Initial conditions
7.4A.4.4.2 Test procedure
7.4A.4.4.3 Message contents
7.4A.4.5 Test requirement
7.4A.4_H Maximum input level for CA (intra band non-contiguous DL CA without UL CA) for 256QAM in DL
7.4A.4_H.1 Test purpose
7.4A.4_H.2 Test applicability
7.4A.4_H.3 Minimum conformance requirements
7.4A.4_H.4 Test description
7.4A.4_H.4.1 Initial conditions
7.4A.4_H.4.2 Test procedure
7.4A.4_H.4.3 Message contents
7.4A.4_H.5 Test requirement
7.4A.5 Maximum input level for 3DL CA
7.4A.5.1 Test purpose
7.4A.5.2 Test applicability
7.4A.5.3 Minimum conformance requirements
7.4A.5.4 Test description
7.4A.5.4.1 Initial conditions
7.4A.5.4.2 Test procedure
7.4A.5.4.3 Message contents
7.4A.5.5 Test requirement
7.4A.5_H Maximum input level for 3DL CA for 256QAM in DL
7.4A.5_H.1 Test purpose
7.4A.5_H.2 Test applicability
7.4A.5_H.3 Minimum conformance requirements
7.4A.5_H.4 Test description
7.4A.5_H.4.1 Initial conditions
7.4A.5_H.4.2 Test procedure
7.4A.5_H.4.3 Message contents
7.4A.5_H.5 Test requirement
7.4A.6
7.4A.7 Maximum input level for 4DL CA
7.4A.7.1 Test purpose
7.4A.7.2 Test applicability
7.4A.7.3 Minimum conformance requirements
7.4A.7.4 Test description
7.4A.7.4.1 Initial conditions
7.4A.7.4.2 Test procedure
7.4A.7.4.3 Message contents
7.4A.7.5 Test requirement
7.4A.7_H Maximum input level for 4DL CA for 256QAM in DL
7.4A.7_H.1 Test purpose
7.4A.7_H.2 Test applicability
7.4A.7_H.3 Minimum conformance requirements
7.4A.7_H.4 Test description
7.4A.7_H.4.1 Initial conditions
7.4A.7_H.4.2 Test procedure
7.4A.7_H.4.3 Message contents
7.4A.7_H.5 Test requirement
7.4A.8 Maximum input level for 5DL CA
7.4A.8.1 Test purpose
7.4A.8.2 Test applicability
7.4A.8.3 Minimum conformance requirements
7.4A.8.4 Test description
7.4A.8.4.1 Initial conditions
7.4A.8.4.2 Test procedure
7.4A.8.4.3 Message contents
7.4A.8.5 Test requirement
7.4A.8_H Maximum input level for 5DL CA for 256QAM in DL
7.4A.8_H.1 Test purpose
7.4A.8_H.2 Test applicability
7.4A.8_H.3 Minimum conformance requirements
7.4A.8_H.4 Test description
7.4A.8_H.4.1 Initial conditions
7.4A.8_H.4.2 Test procedure
7.4A.8_H.4.3 Message contents
7.4A.8_H.5 Test requirement
7.4B Maximum input level for UL-MIMO
7.4B.1 Test purpose
7.4B.2 Test applicability
7.4B.3 Minimum conformance requirements
7.4B.4 Test description
7.4B.4.1 Initial conditions
7.4B.4.2 Test procedure
7.4B.4.3 Message contents
7.4B.5 Test requirement
7.4C
7.4D Maximum input level for ProSe
7.4D.0 Minimum conformance requirements
7.4D.1 Maximum input level for ProSe Direct Discovery
7.4D.1.1 Test purpose
7.4D.1.2 Test applicability
7.4D.1.3 Minimum conformance requirements
7.4D.1.4 Test description
7.4D.1.4.1 Initial conditions
7.4D.1.4.2 Test procedure
7.4D.1.4.3 Message contents
7.4D.1.5 Test requirement
7.4D.2 Maximum input level for ProSe Direct Communication
7.4D.2.1 Test purpose
7.4D.2.2 Test applicability
7.4D.2.3 Minimum conformance requirements
7.4D.2.4 Test description
7.4D.2.4.1 Initial conditions
7.4D.2.4.2 Test procedure
7.4D.2.4.3 Message contents
7.4D.2.5 Test requirements
7.4E Maximum input level for UE category 0
7.4E.1 Test purpose
7.4E.2 Test applicability
7.4E.3 Minimum conformance requirements
7.4E.4 Test description
7.4E.4.1 Initial conditions
7.4E.4.2 Test procedure
7.4E.4.3 Message contents
7.4E.5 Test requirement
7.4EA Maximum input level for UE category M1
7.4EA.1 Test purpose
7.4EA.2 Test applicability
7.4EA.3 Minimum conformance requirements
7.4EA.4 Test description
7.4EA.4.1 Initial conditions
7.4EA.4.2 Test procedure
7.4EA.4.3 Message contents
7.4EA.5 Test requirement
7.4EB Maximum input level for UE Category 1bis
7.4EB.1 Test purpose
7.4EB.2 Test applicability
7.4EB.3 Minimum conformance requirements
7.4EB.4 Test description
7.4EB.4.1 Initial conditions
7.4EB.4.2 Test procedure
7.4EB.4.3 Message contents
7.4EB.5 Test requirement
7.4EC Maximum input level for UE category M2
7.4EC.1 Test purpose
7.4EC.2 Test applicability
7.4EC.3 Minimum conformance requirements
7.4EC.4 Test description
7.4EC.4.1 Initial conditions
7.4EC.4.2 Test procedure
7.4EC.4.3 Message contents
7.4EC.5 Test requirement
7.4F Maximum input level for category NB1 and NB2
7.4F.1 Test Purpose
7.4F.2 Test Applicability
7.4F.3 Minimum Conformance Requirements
7.4F.4 Test Description
7.4F.4.1 Initial Conditions
7.4F.4.2 Test Procedure
7.4F.4.3 Message Contents
7.4F.5 Test requirement
7.4G Maximum input level for V2X Communication
7.4G.1 Maximum input level for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.4G.1.1 Test purpose
7.4G.1.2 Test applicability
7.4G.1.3 Minimum conformance requirements
7.4G.1.4 Test description
7.4G.1.4.1 Initial conditions
7.4G.1.4.2 Test procedure
7.4G.1.4.3 Message contents
7.4G.1.5 Test requirements
7.4G.2 Maximum input level for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.4G.2.1 Test purpose
7.4G.2.2 Test applicability
7.4G.2.3 Minimum conformance requirements
7.4G.2.4 Test description
7.4G.2.4.1 Initial conditions
7.4G.2.4.2 Test procedure
7.4G.2.4.3 Message contents
7.4G.2.5 Test requirements
7.4G.3 Maximum input level for V2X Communication / Intra-band contiguous multi-carrier operation
7.4G.3.1 Test purpose
7.4G.3.2 Test applicability
7.4G.3.3 Minimum conformance requirements
7.4G.3.4 Test description
7.4G.3.4.1 Initial conditions
7.4G.3.4.2 Test procedure
7.4G.3.4.3 Message contents
7.4G.3.5 Test requirements
7.5 Adjacent Channel Selectivity (ACS)
7.5.1 Test purpose
7.5.2 Test applicability
7.5.3 Minimum conformance requirements
7.5.4 Test description
7.5.4.1 Initial conditions
7.5.4.2 Test procedure
7.5.4.3 Message contents
7.5.5 Test requirement
7.5_1 Adjacent Channel Selectivity (ACS) with 4 Rx antenna ports
7.5_1.1 Test purpose
7.5_1.2 Test applicability
7.5_1.3 Minimum conformance requirements
7.5_1.4 Test description
7.5.4_1.1 Initial conditions
7.5_1.4.2 Test procedure
7.5_1.4.3 Message contents
7.5_1.5 Test requirement
7.5A Adjacent Channel Selectivity (ACS) for CA
7.5A.1 Adjacent Channel Selectivity (ACS) for CA (intra-band contiguous DL CA and UL CA)
7.5A.1.1 Test purpose
7.5A.1.2 Test applicability
7.5A.1.3 Minimum conformance requirements
7.5A.1.4 Test description
7.5A.1.4.1 Initial conditions
7.5A.1.4.2 Test procedure
7.5A.1.4.3 Message contents
7.5A.1.5 Test Requirements
7.5A.2 Adjacent Channel Selectivity (ACS) for CA (intra-band contiguous DL CA without UL CA)
7.5A.2.1 Test purpose
7.5A.2.2 Test applicability
7.5A.2.3 Minimum conformance requirements
7.5A.2.4 Test description
7.5A.2.4.1 Initial conditions
7.5A.2.4.2 Test procedure
7.5A.2.4.3 Message contents
7.5A.2.5 Test Requirements
7.5A.3 Adjacent Channel Selectivity (ACS) for CA (inter-band DL CA without UL CA)
7.5A.3.1 Test purpose
7.5A.3.2 Test applicability
7.5A.3.3 Minimum conformance requirements
7.5A.3.4 Test description
7.5A.3.4.1 Initial conditions
7.5A.3.4.2 Test procedure
7.5A.3.4.3 Message contents
7.5A.3.5 Test Requirements
7.5A.4 Adjacent Channel Selectivity (ACS) for CA (intra-band non-contiguous DL CA without UL CA)
7.5A.4.1 Test purpose
7.5A.4.2 Test applicability
7.5A.4.3 Minimum conformance requirements
7.5A.4.4 Test description
7.5A.4.4.1 Initial conditions
7.5A.4.4.2 Test procedure
7.5A.4.4.3 Message contents
7.5A.4.5 Test requirement
7.5A.5 Adjacent Channel Selectivity (ACS) for 3DL CA
7.5A.5.1 Test purpose
7.5A.5.2 Test applicability
7.5A.5.3 Minimum conformance requirements
7.5A.5.4 Test description
7.5A.5.4.1 Initial conditions
7.5A.5.4.2 Test procedure
7.5A.5.4.3 Message contents
7.5A.5.5 Test requirement
7.5A.6
7.5A.7 Adjacent Channel Selectivity (ACS) for 4DL CA
7.5A.7.1 Test purpose
7.5A.7.2 Test applicability
7.5A.7.3 Minimum conformance requirements
7.5A.7.4 Test description
7.5A.7.4.1 Initial conditions
7.5A.7.4.2 Test procedure
7.5A.7.4.3 Message contents
7.5A.7.5 Test requirement
7.5A.8 Adjacent Channel Selectivity (ACS) for 5DL CA
7.5A.8.1 Test purpose
7.5A.8.2 Test applicability
7.5A.8.3 Minimum conformance requirements
7.5A.8.4 Test description
7.5A.8.4.1 Initial conditions
7.5A.8.4.2 Test procedure
7.5A.8.4.3 Message contents
7.5A.8.5 Test requirement
7.5B Adjacent Channel Selectivity (ACS) for UL-MIMO
7.5B.1 Test purpose
7.5B.2 Test applicability
7.5B.3 Minimum conformance requirements
7.5B.4 Test description
7.5B.4.1 Initial conditions
7.5B.4.2 Test procedure
7.5B.4.3 Message contents
7.5B.5 Test requirement
7.5D Adjacent Channel Selectivity (ACS) for ProSe
7.5D.0 Minimum conformance requirements
7.5D.1 Adjacent Channel Selectivity (ACS) for ProSe Direct Discovery
7.5D.1.1 Test Purpose
7.5D.1.2 Test Applicability
7.5D.1.3 Minimum Conformance Requirements
7.5D.1.4 Test Description
7.5D.1.4.1 Initial Conditions
7.5D.1.4.2 Test Procedure
7.5D.1.4.3 Message Contents
7.5D.1.5 Test Requirement
7.5D.2 Adjacent Channel Selectivity (ACS) for ProSe Direct Communication
7.5D.2.1 Test Purpose
7.5D.2.2 Test Applicability
7.5D.2.3 Minimum Conformance Requirements
7.5D.2.4 Test Description
7.5D.2.4.1 Initial Conditions
7.5D.2.4.2 Test Procedure
7.5D.2.4.3 Message Contents
7.5D.2.5 Test Requirement
7.5E Adjacent Channel Selectivity (ACS) for category 0
7.5E.1 Test purpose
7.5E.2 Test applicability
7.5E.3 Minimum conformance requirements
7.5E.4 Test description
7.5E.4.1 Initial conditions
7.5E.4.2 Test procedure
7.5E.4.3 Message contents
7.5E.5 Test requirement
7.5EA Adjacent Channel Selectivity (ACS) for UE category M1
7.5EA.1 Test purpose
7.5EA.2 Test applicability
7.5EA.3 Minimum conformance requirements
7.5EA.4 Test description
7.5EA.4.1 Initial conditions
7.5EA.4.2 Test procedure
7.5EA.4.3 Message contents
7.5EA.5 Test requirement
7.5EB Adjacent Channel Selectivity (ACS) for UE Category 1bis
7.5EB.1 Test purpose
7.5EB.2 Test applicability
7.5EB.3 Minimum conformance requirements
7.5EB.4 Test description
7.5EB.4.1 Initial conditions
7.5EB.4.2 Test procedure
7.5EB.4.3 Message contents
7.5EB.5 Test requirement
7.5EC Adjacent Channel Selectivity (ACS) for UE category M2
7.5EC.1 Test purpose
7.5EC.2 Test applicability
7.5EC.3 Minimum conformance requirements
7.5EC.4 Test description
7.5EC.4.1 Initial conditions
7.5EC.4.2 Test procedure
7.5EC.4.3 Message contents
7.5EC.5 Test requirement
7.5F Adjacent Channel Selectivity (ACS) for category NB1 and NB2
7.5F.1 Test purpose
7.5F.2 Test applicability
7.5F.3 Minimum conformance requirements
7.5F.4 Test description
7.5F.4.1 Initial conditions
7.5F.4.2 Test procedure
7.5F.4.3 Message contents
7.5F.5 Test requirement
7.5G Adjacent Channel Selectivity (ACS) for V2X Communication
7.5G.1 Adjacent channel selectivity (ACS) for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.5G.1.1 Test Purpose
7.5G.1.2 Test Applicability
7.5G.1.3 Minimum Conformance Requirements
7.5G.1.4 Test Description
7.5G.1.4.1 Initial Conditions
7.5G.1.4.2 Test Procedure
7.5G.1.4.3 Message Contents
7.5G.1.5 Test Requirement
7.5G.2 Adjacent channel selectivity (ACS) for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissi
7.5G.2.1 Test Purpose
7.5G.2.2 Test Applicability
7.5G.2.3 Minimum Conformance Requirements
7.5G.2.4 Test Description
7.5G.2.4.1 Initial Conditions
7.5G.2.4.2 Test Procedure
7.5G.2.4.3 Message Contents
7.5G.2.5 Test Requirement
7.5G.3 Adjacent channel selectivity (ACS) for V2X Communication / Intra-band contiguous multi-carrier operation
7.5G.3.1 Test Purpose
7.5G.3.2 Test Applicability
7.5G.3.3 Minimum Conformance Requirements
7.5G.3.4 Test Description
7.5G.3.4.1 Initial Conditions
7.5G.3.4.2 Test Procedure
7.5G.3.4.3 Message Contents
7.5G.3.5 Test Requirement
7.6 Blocking characteristics
7.6.1 In-band blocking
7.6.1.1 Test Purpose
7.6.1.2 Test Applicability
7.6.1.3 Minimum Conformance Requirements
7.6.1.4 Test Description
7.6.1.4.1 Initial Conditions
7.6.1.4.2 Test Procedure
7.6.1.4.3 Message Contents
7.6.1.5 Test Requirement
7.6.1_1 In-band blocking with 4 Rx antenna ports
7.6.1_1.1 Test Purpose
7.6.1_1.2 Test Applicability
7.6.1_1.3 Minimum Conformance Requirements
7.6.1_1.4 Test Description
7.6.1_1.4.1 Initial Conditions
7.6.1_1.4.2 Test Procedure
7.6.1_1.4.3 Message Contents
7.6.1_1.5 Test Requirement
7.6.1A In-band blocking for CA
7.6.1A.0 Minimum conformance requirements
7.6.1A.1 In-band blocking for CA (intra-band contiguous DL CA and UL CA)
7.6.1A.1.1 Test Purpose
7.6.1A.1.2 Test Applicability
7.6.1A.1.3 Minimum Conformance Requirements
7.6.1A.1.4 Test Description
7.6.1A.1.5 Test Requirement
7.6.1A.2 In-band blocking for CA (intra-band contiguous DL CA without UL CA)
7.6.1A.2.1 Test Purpose
7.6.1A.2.2 Test Applicability
7.6.1A.2.3 Minimum Conformance Requirements
7.6.1A.2.4 Test Description
7.6.1A.2.4.1 Initial Conditions
7.6.1A.2.4.2 Test Procedure
7.6.1A.2.4.3 Message Contents
7.6.1A.2.5 Test Requirement
7.6.1A.3 In-band blocking for CA (inter-band DL CA without UL CA)
7.6.1A.3.1 Test Purpose
7.6.1A.3.2 Test Applicability
7.6.1A.3.3 Minimum Conformance Requirements
7.6.1A.3.4 Test Description
7.6.1A.3.4.1 Initial Conditions
7.6.1A.3.4.2 Test Procedure
7.6.1A.3.4.3 Message Contents
7.6.1A.3.5 Test Requirement
7.6.1A.4 In-band blocking for CA (intra-band non-contiguous DL CA without UL CA)
7.6.1A.4.1 Test Purpose
7.6.1A.4.2 Test Applicability
7.6.1A.4.3 Minimum Conformance Requirements
7.6.1A.4.4 Test description
7.6.1A.4.4.1 Initial Conditions
7.6.1A.4.4.2 Test Procedure
7.6.1A.4.4.3 Message Contents
7.6.1A.4.5 Test Requirement
7.6.1A.5 In-band blocking for 3DL CA
7.6.1A.5.1 Test Purpose
7.6.1A.5.2 Test Applicability
7.6.1A.5.4 Test Description
7.6.1A.5.4.1 Initial Conditions
7.6.1A.5.4.2 Test Procedure
7.6.1A.5.4.3 Message Contents
7.6.1A.5.5 Test Requirement
7.6.1A.6
7.6.1A.7 In-band blocking for 4DL CA
7.6.1A.7.1 Test Purpose
7.6.1A.7.2 Test Applicability
7.6.1A.7.3 Minimum Conformance Requirements
7.6.1A.7.4 Test Description
7.6.1A.7.4.1 Initial Conditions
7.6.1A.7.4.2 Test Procedure
7.6.1A.7.4.3 Message Contents
7.6.1A.7.5 Test Requirement
7.6.1A.8 In-band blocking for 5DL CA
7.6.1A.8.1 Test Purpose
7.6.1A.8.2 Test Applicability
7.6.1A.8.3 Minimum Conformance Requirements
7.6.1A.8.4 Test Description
7.6.1A.8.4.1 Initial Conditions
7.6.1A.8.4.2 Test Procedure
7.6.1A.8.4.3 Message Contents
7.6.1A.8.5 Test Requirement
7.6.1B In-band blocking for UL-MIMO
7.6.1B.1 Test Purpose
7.6.1B.2 Test Applicability
7.6.1B.3 Minimum Conformance Requirements
7.6.1B.4 Test Description
7.6.1B.4.1 Initial Conditions
7.6.1B.4.2 Test Procedure
7.6.1B.4.3 Message Contents
7.6.1B.5 Test Requirement
7.6.1D In-band blocking for ProSe
7.6.1D.0 Minimum conformance requirements
7.6.1D.1 In-band blocking for ProSe Direct Discovery
7.6.1D.1.1 Test Purpose
7.6.1D.1.2 Test Applicability
7.6.1D.1.3 Minimum Conformance Requirements
7.6.1D.1.4 Test Description
7.6.1D.1.5 Test Requirement
7.6.1D.2 In-band blocking for ProSe Direct Communication
7.6.1D.2.1 Test Purpose
7.6.1D.2.2 Test Applicability
7.6.1D.2.3 Minimum Conformance Requirements
7.6.1D.2.4 Test Description
7.6.1D.2.5 Test Requirement
7.6.1E In-band blocking for UE category 0
7.6.1E.1 Test Purpose
7.6.1E.2 Test Applicability
7.6.1E.3 Minimum Conformance Requirements
7.6.1E.4 Test Description
7.6.1E.4.1 Initial Conditions
7.6.1E.4.2 Test Procedure
7.6.1E.4.3 Message Contents
7.6.1E.5 Test Requirement
7.6.1EB In-band blocking for UE Category 1bis
7.6.1EB.1 Test Purpose
7.6.1EB.2 Test Applicability
7.6.1EB.3 Minimum Conformance Requirements
7.6.1EB.4 Test Description
7.6.1EB.4.2 Test Procedure
7.6.1EB.4.3 Message Contents
7.6.1EB.5 Test Requirement
7.6.1EC In-band blocking for UE category M2
7.6.1EC.1 Test purpose
7.6.1EC.2 Test applicability
7.6.1EC.3 Minimum conformance requirements
7.6.1EC.4 Test description
7.6.1EC.4.1 Initial conditions
7.6.1EC.4.2 Test procedure
7.6.1EC.4.3 Message contents
7.6.1EC.5 Test requirement
7.6.1F In-band blocking for category NB1 and NB2
7.6.1F.1 Test Purpose
7.6.1F.2 Test Applicability
7.6.1F.3 Minimum Conformance Requirements
7.6.1F.4 Test Description
7.6.1F.4.1 Initial Conditions
7.6.1F.4.2 Test Procedure
7.6.1F.4.3 Message Contents
7.6.1F.5 Test Requirement
7.6.1G In-band blocking for V2X Communication
7.6.1G.1 In-band blocking for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.6.1G.1.1 Test Purpose
7.6.1G.1.2 Test Applicability
7.6.1G.1.3 Minimum Conformance Requirements
7.6.1G.1.4 Test Description
7.6.1G.1.5 Test Requirement
7.6.1G.2 In-band blocking for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.6.1G.2.1 Test Purpose
7.6.1G.2.2 Test Applicability
7.6.1G.2.3 Minimum Conformance Requirements
7.6.1G.2.4 Test Description
7.6.1G.2.4.1 Initial conditions
7.6.1G.2.4.2 Test procedure
7.6.1G.2.4.3 Message contents
7.6.1G.2.5 Test Requirement
7.6.1G.3 In-band blocking for V2X Communication / Intra-band contiguous multi-carrier operation
7.6.1G.3.1 Test Purpose
7.6.1G.3.2 Test Applicability
7.6.1G.3.3 Minimum Conformance Requirements
7.6.1G.3.4 Test Description
7.6.1G.3.4.1 Initial conditions
7.6.1G.3.4.2 Test procedure
7.6.1G.3.4.3 Message contents
7.6.1G.3.5 Test Requirement
7.6.1EA In-band blocking for UE category M1
7.6.1EA.1 Test Purpose
7.6.1EA.2 Test Applicability
7.6.1EA.3 Minimum Conformance Requirements
7.6.1EA.4 Test Description
7.6.1EA.4.1 Initial Conditions
7.6.1EA.4.2 Test Procedure
7.6.1EA.4.3 Message Contents
7.6.1EA.5 Test Requirement
7.6.2 Out-of-band blocking
7.6.2.1 Test Purpose
7.6.2.2 Test Applicability
7.6.2.3 Minimum Conformance Requirements
7.6.2.4 Test Description
7.6.2.4.1 Initial Conditions
7.6.2.4.2 Test Procedure
7.6.2.4.3 Message Contents
7.6.2.5 Test Requirement
7.6.2_1 Out-of-band blocking with 4 Rx antenna ports
7.6.2_1.1 Test Purpose
7.6.2_1.2 Test Applicability
7.6.2_1.3 Minimum Conformance Requirements
7.6.2_1.4 Test Description
7.6.2_1.4.1 Initial Conditions
7.6.2_1.4.2 Test Procedure
7.6.2_1.4.3 Message Contents
7.6.2_1.5 Test Requirement
7.6.2A Out-of-band blocking for CA
7.6.2A.0 Minimum conformance requirements
7.6.2A.1 Out-of-band blocking for CA (intra-band contiguous DL CA and UL CA)
7.6.2A.1.1 Test Purpose
7.6.2A.1.2 Test Applicability
7.6.2A.1.3 Minimum Conformance Requirements
7.6.2A.1.4 Test Description
7.6.2A.1.5 Test Requirement
7.6.2A.2 Out-of-band blocking for CA (intra-band contiguous DL CA without UL CA)
7.6.2A.2.1 Test Purpose
7.6.2A.2.2 Test Applicability
7.6.2A.2.3 Minimum Conformance Requirements
7.6.2A.2.4 Test Description
7.6.2A.2.4.1 Initial Conditions
7.6.2A.2.4.2 Test Procedure
7.6.2A.2.4.3 Message Contents
7.6.2A.2.5 Test Requirement
7.6.2A.3 Out-of-band blocking for CA (inter-band DL CA without UL CA)
7.6.2A.3.1 Test Purpose
7.6.2A.3.2 Test Applicability
7.6.2A.3.3 Minimum Conformance Requirements
7.6.2A.3.4 Test Description
7.6.2A.3.4.1 Initial Conditions
7.6.2A.3.4.2 Test Procedure
7.6.2A.3.4.3 Message Contents
7.6.2A.3.5 Test Requirement
7.6.2A.4 Out-of-band blocking for CA (intra-band non-contiguous DL CA without UL CA)
7.6.2A.4.1 Test Purpose
7.6.2A.4.2 Test Applicability
7.6.2A.4.3 Minimum Conformance Requirements
7.6.2A.4.4 Test description
7.6.2A.4.4.1 Initial Conditions
7.6.2A.4.4.2 Test Procedure
7.6.2A.4.4.3 Message Contents
7.6.2A.4.5 Test Requirement
7.6.2A.5 Out-of-band blocking for 3DL CA
7.6.2A.5.1 Test Purpose
7.6.2A.5.2 Test Applicability
7.6.2A.5.3 Minimum Conformance Requirements
7.6.2A.5.4 Test Description
7.6.2A.5.4.1 Initial Conditions
7.6.2A.5.4.2 Test Procedure
7.6.2A.5.4.3 Message Contents
7.6.2A.5.5 Test Requirement
7.6.2A.6
7.6.2A.7 Out-of-band blocking for 4DL CA
7.6.2A.7.1 Test Purpose
7.6.2A.7.2 Test Applicability
7.6.2A.7.3 Minimum Conformance Requirements
7.6.2A.7.4 Test Description
7.6.2A.7.4.1 Initial Conditions
7.6.2A.7.4.2 Test Procedure
7.6.2A.7.4.3 Message Contents
7.6.2A.7.5 Test Requirement
7.6.2A.8 Out-of-band blocking for 5DL CA
7.6.2A.8.1 Test Purpose
7.6.2A.8.2 Test Applicability
7.6.2A.8.3 Minimum Conformance Requirements
7.6.2A.8.4 Test Description
7.6.2A.8.4.1 Initial Conditions
7.6.2A.8.4.2 Test Procedure
7.6.2A.8.4.3 Message Contents
7.6.2A.8.5 Test Requirement
7.6.2B Out-of-band blocking for UL-MIMO
7.6.2B.1 Test Purpose
7.6.2B.2 Test Applicability
7.6.2B.3 Minimum Conformance Requirements
7.6.2B.4 Test Description
7.6.2B.4.1 Initial Conditions
7.6.2B.4.2 Test Procedure
7.6.2B.4.3 Message Contents
7.6.2B.5 Test Requirement
7.6.2D Out-of-band blocking for ProSe
7.6.2D.0 Minimum conformance requirements
7.6.2D.1 Out-of-band blocking for ProSe Direct Discovery
7.6.2D.1.1 Test Purpose
7.6.2D.1.2 Test Applicability
7.6.2D.1.3 Minimum Conformance Requirements
7.6.2D.1.4 Test Description
7.6.2D.1.5 Test Requirement
7.6.2D.2 Out-of-band blocking for Prose Direct Communication
7.6.2D.2.1 Test Purpose
7.6.2D.2.2 Test Applicability
7.6.2D.2.3 Minimum Conformance Requirements
7.6.2D.2.4 Test Description
7.6.2D.2.5 Test Requirement
7.6.2E Out-of-band blocking for UE category 0
7.6.2E.1 Test Purpose
7.6.2E.2 Test Applicability
7.6.2E.3 Minimum Conformance Requirements
7.6.2E.4 Test Description
7.6.2E.4.1 Initial Conditions
7.6.2E.4.2 Test Procedure
7.6.2E.4.3 Message Contents
7.6.2E.5 Test Requirement
7.6.2EB Out-of-band blocking for UE category 1bis
7.6.2EB.1 Test Purpose
7.6.2EB.2 Test Applicability
7.6.2EB.3 Minimum Conformance Requirements
7.6.2EB.4 Test Description
7.6.2EB.4.1 Initial Conditions
7.6.2EB.4.2 Test Procedure
7.6.2EB.4.3 Message Contents
7.6.2EB.5 Test Requirement
7.6.2G Out-of-band blocking for V2X Communication
7.6.2G.1 Out-of-band blocking for V2X Communication/ Non-concurrent with E-UTRA uplink transmissions
7.6.2G.1.1 Test Purpose
7.6.2G.1.2 Test Applicability
7.6.2G.1.3 Minimum Conformance Requirements
7.6.2G.1.4 Test Description
7.6.2G.1.5 Test Requirement
7.6.2G.2 Out-of-band blocking for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.6.2G.2.1 Test Purpose
7.6.2G.2.2 Test Applicability
7.6.2G.2.3 Minimum Conformance Requirements
7.6.2G.2.4 Test Description
7.6.2G.2.4.1 Initial conditions
7.6.2G.2.4.2 Test procedure
7.6.2G.2.4.3 Message contents
7.6.2G.2.5 Test Requirement
7.6.2G.3 Out-of-band blocking for V2X Communication / Intra-band contiguous multi-carrier operation
7.6.2G.3.1 Test Purpose
7.6.2G.3.2 Test Applicability
7.6.2G.3.3 Minimum Conformance Requirements
7.6.2G.3.4 Test Description
7.6.2G.3.4.1 Initial conditions
7.6.2G.3.4.2 Test procedure
7.6.2G.3.4.3 Message contents
7.6.2G.3.5 Test Requirement
7.6.2F Out-of-band blocking for category NB1 and NB2
7.6.2F.1 Test Purpose
7.6.2F.2 Test Applicability
7.6.2F.3 Minimum Conformance Requirements
7.6.2F.4 Test Description
7.6.2F.4.1 Initial Conditions
7.6.2F.4.2 Test Procedure
7.6.2F.4.3 Message Contents
7.6.2F.5 Test Requirement
7.6.2EA Out-of-band blocking for UE category M1
7.6.2EA.1 Test Purpose
7.6.2EA.2 Test Applicability
7.6.2EA.3 Minimum Conformance Requirements
7.6.2EA.4 Test Description
7.6.2EA.4.1 Initial Conditions
7.6.2EA.4.2 Test Procedure
7.6.2EA.4.3 Message Contents
7.6.2EA.5 Test Requirement
7.6.3 Narrow band blocking
7.6.3.1 Test Purpose
7.6.3.2 Test Applicability
7.6.3.3 Minimum Conformance Requirements
7.6.3.4 Test Description
7.6.3.4.1 Initial Conditions
7.6.3.4.2 Test Procedure
7.6.3.4.3 Message Contents
7.6.3.5 Test Requirement
7.6.3_1 Narrow band blocking with 4 Rx antenna ports
7.6.3_1.1 Test Purpose
7.6.3_1.2 Test Applicability
7.6.3_1.3 Minimum Conformance Requirements
7.6.3_1.4 Test Description
7.6.3_1.4.1 Initial Conditions
7.6.3_1.4.2 Test Procedure
7.6.3_1.4.3 Message Contents
7.6.3_1.5 Test Requirement
7.6.3A Narrow band blocking for CA
7.6.3A.0 Minimum conformance requirements
7.6.3A.1 Narrow band blocking for CA (intra-band contiguous DL CA and UL CA)
7.6.3A.1.1 Test Purpose
7.6.3A.1.2 Test Applicability
7.6.3A.1.3 Minimum Conformance Requirements
7.6.3A.1.4 Test Description
7.6.3A.1.5 Test Requirement
7.6.3A.2 Narrow band blocking for CA (intra-band contiguous DL CA without UL CA)
7.6.3A.2.1 Test Purpose
7.6.3A.2.2 Test Applicability
7.6.3A.2.3 Minimum Conformance Requirements
7.6.3A.2.4 Test Description
7.6.3A.2.4.1 Initial Conditions
7.6.3A.2.4.2 Test Procedure
7.6.3A.2.4.3 Message Contents
7.6.3A.2.5 Test Requirement
7.6.3A.3 Narrow band blocking for CA (inter-band DL CA without UL CA)
7.6.3A.3.1 Test Purpose
7.6.3A.3.2 Test Applicability
7.6.3A.3.3 Minimum Conformance Requirements
7.6.3A.3.4 Test Description
7.6.3A.3.4.1 Initial Conditions
7.6.3A.3.4.2 Test Procedure
7.6.3A.3.4.3 Message Contents
7.6.3A.3.5 Test Requirement
7.6.3A.4 Narrow band blocking for CA (intra-band non-contiguous DL CA without UL CA)
7.6.3A.4.1 Test Purpose
7.6.3A.4.2 Test Applicability
7.6.3A.4.3 Minimum Conformance Requirements
7.6.3A.4.4 Test description
7.6.3A.4.4.1 Initial Conditions
7.6.3A.4.4.2 Test Procedure
7.6.3A.4.4.3 Message Contents
7.6.3A.4.5 Test Requirement
7.6.3A.5 Narrow band blocking for 3DL CA
7.6.3A.5.1 Test Purpose
7.6.3A.5.2 Test Applicability
7.6.3A.5.3 Minimum Conformance Requirements
7.6.3A.5.4 Test Description
7.6.3A.5.4.1 Initial Conditions
7.6.3A.5.4.2 Test Procedure
7.6.3A.5.4.3 Message Contents
7.6.3A.5.5 Test Requirement
7.6.3A.6
7.6.3A.7 Narrow band blocking for 4DL CA
7.6.3A.7.1 Test Purpose
7.6.3A.7.2 Test Applicability
7.6.3A.7.3 Minimum Conformance Requirements
7.6.3A.7.4 Test Description
7.6.3A.7.4.1 Initial Conditions
7.6.3A.7.4.2 Test Procedure
7.6.3A.7.4.3 Message Contents
7.6.3A.7.5 Test Requirement
7.6.3A.8 Narrow band blocking for 5DL CA
7.6.3A.8.1 Test Purpose
7.6.3A.8.2 Test Applicability
7.6.3A.8.3 Minimum Conformance Requirements
7.6.3A.8.4 Test Description
7.6.3A.8.4.1 Initial Conditions
7.6.3A.8.4.2 Test Procedure
7.6.3A.8.4.3 Message Contents
7.6.3A.8.5 Test Requirement
7.6.3B Narrow band blocking for UL-MIMO
7.6.3B.1 Test Purpose
7.6.3B.2 Test Applicability
7.6.3B.3 Minimum Conformance Requirements
7.6.3B.4 Test Description
7.6.3B.4.1 Initial Conditions
7.6.3B.4.2 Test Procedure
7.6.3B.4.3 Message Contents
7.6.3B.5 Test Requirement
7.6.3D Narrow band blocking for ProSe
7.6.3D.0 Minimum conformance requirements
7.6.3D.1 Narrow band blocking for ProSe Direct Discovery
7.6.3D.1.1 Test Purpose
7.6.3D.1.2 Test Applicability
7.6.3D.1.3 Minimum Conformance Requirements
7.6.3D.1.4 Test Description
7.6.3D.1.5 Test Requirement
7.6.3D.2 Narrow band blocking for ProSe Direct Communication
7.6.3D.2.1 Test Purpose
7.6.3D.2.2 Test Applicability
7.6.3D.2.3 Minimum Conformance Requirements
7.6.3D.2.4 Test Description
7.6.3D.2.5 Test Requirement
7.6.3E Narrow band blocking for UE category 0
7.6.3E.1 Test Purpose
7.6.3E.2 Test Applicability
7.6.3E.3 Minimum Conformance Requirements
7.6.3E.4 Test Description
7.6.3E.4.1 Initial Conditions
7.6.3E.4.2 Test Procedure
7.6.3E.4.3 Message Contents
7.6.3E.5 Test Requirement
7.6.3EA Narrow band blocking for UE Category M1
7.6.3EA.1 Test Purpose
7.6.3EA.2 Test Applicability
7.6.3EA.3 Minimum Conformance Requirements
7.6.3EA.4 Test Description
7.6.3EA.4.1 Initial Conditions
7.6.3EA.4.2 Test Procedure
7.6.3EA.4.3 Message Contents
7.6.3EA.5 Test Requirement
7.6.3EB Narrow band blocking for UE category 1bis
7.6.3EB.1 Test Purpose
7.6.3EB.2 Test Applicability
7.6.3EB.3 Minimum Conformance Requirements
7.6.3EB.4 Test Description
7.6.3EB.4.1 Initial Conditions
7.6.3E.4.2 Test Procedure
7.6.3EB.4.3 Message Contents
7.6.3EB.5 Test Requirement
7.6.3EC Narrow band blocking for UE category M2
7.6.3EC.1 Test purpose
7.6.3EC.2 Test applicability
7.6.3EC.3 Minimum conformance requirements
7.6.3EC.4 Test description
7.6.3EC.4.1 Initial conditions
7.6.3EC.4.2 Test procedure
7.6.3EC.4.3 Message contents
7.6.3EC.5 Test requirement
7.7 Spurious response
7.7.1 Test Purpose
7.7.2 Test Applicability
7.7.3 Minimum Conformance Requirements
7.7.4 Test Description
7.7.4.1 Initial Conditions
7.7.4.2 Test Procedure
7.7.4.3 Message Contents
7.7.5 Test Requirement
7.7_1 Spurious response with 4 Rx antenna ports
7.7_1.1 Test Purpose
7.7_1.2 Test Applicability
7.7_1.3 Minimum Conformance Requirements
7.7_1.4 Test Description
7.7_1.4.1 Initial Conditions
7.7_1.4.2 Test Procedure
7.7_1.4.3 Message Contents
7.7_1.5 Test Requirement
7.7A Spurious response for CA
7.7A.0 Minimum conformance requirements
7.7A.1 Spurious response for CA (intra-band contiguous DL CA and UL CA)
7.7A.1.1 Test Purpose
7.7A.1.2 Test Applicability
7.7A.1.3 Minimum Conformance Requirements
7.7A.1.4 Test Description
7.7A.1.4.1 Initial Conditions
7.7A.1.4.2 Test Procedure
7.7A.1.4.3 Message Contents
7.7A.1.5 Test Requirement
7.7A.2 Spurious response for CA (intra-band contiguous DL CA without UL CA)
7.7A.2.1 Test Purpose
7.7A.2.2 Test Applicability
7.7A.2.3 Minimum Conformance Requirements
7.7A.2.4 Test Description
7.7A.2.4.1 Initial Conditions
7.7A.2.4.2 Test Procedure
7.7A.2.4.3 Message Contents
7.7A.2.5 Test Requirement
7.7A.3 Spurious response for CA (inter-band DL CA without UL CA)
7.7A.3.1 Test Purpose
7.7A.3.2 Test Applicability
7.7A.3.3 Minimum Conformance Requirements
7.7A.3.4 Test Description
7.7A.3.4.1 Initial Conditions
7.7A.3.4.2 Test Procedure
7.7A.3.4.3 Message Contents
7.7A.3.5 Test Requirement
7.7A.4 Spurious response for CA (intra-band non-contiguous DL CA without UL CA)
7.7A.4.1 Test Purpose
7.7A.4.2 Test Applicability
7.7A.4.3 Minimum Conformance Requirements
7.7A.4.4 Test Description
7.7A.4.4.1 Initial Conditions
7.7A.4.4.2 Test Procedure
7.7A.4.4.3 Message Contents
7.7A.4.5 Test Requirement
7.7A.5 Spurious response for 3DL CA
7.7A.5.1 Test Purpose
7.7A.5.2 Test Applicability
7.7A.5.3 Minimum Conformance Requirements
7.7A.5.4 Test Description
7.7A.5.4.1 Initial Conditions
7.7A.5.4.2 Test Procedure
7.7A.5.4.3 Message Contents
7.7A.5.5 Test Requirement
7.7A.6
7.7A.7 Spurious response for 4DL CA
7.7A.7.1 Test Purpose
7.7A.7.2 Test Applicability
7.7A.7.3 Minimum Conformance Requirements
7.7A.7.4 Test Description
7.7A.7.4.1 Initial Conditions
7.7A.7.4.2 Test Procedure
7.7A.7.4.3 Message Contents
7.7A.7.5 Test Requirement
7.7A.8 Spurious response for 5DL CA
7.7A.8.1 Test Purpose
7.7A.8.2 Test Applicability
7.7A.8.3 Minimum Conformance Requirements
7.7A.8.4 Test Description
7.7A.8.4.1 Initial Conditions
7.7A.8.4.2 Test Procedure
7.7A.8.4.3 Message Contents
7.7A.8.5 Test Requirement
7.7B Spurious response for UL-MIMO
7.7B.1 Test Purpose
7.7B.2 Test Applicability
7.7B.3 Minimum Conformance Requirements
7.7B.4 Test Description
7.7B.4.1 Initial Conditions
7.7B.4.2 Test Procedure
7.7B.4.3 Message Contents
7.7B.5 Test Requirement
7.7D Spurious response for ProSe
7.7D.0 Minimum conformance requirements
7.7D.1 Spurious response for ProSe Direct Discovery
7.7D.1.1 Test Purpose
7.7D.1.2 Test Applicability
7.7D.1.3 Minimum Conformance Requirements
7.7D.1.4 Test Description
7.7D.1.4.1 Initial Conditions
7.7D.1.4.2 Test Procedure
7.7D.1.4.3 Message Contents
7.7D.1.5 Test Requirement
7.7D.2 Spurious response for ProSe Direct Communication
7.7D.2.1 Test Purpose
7.7D.2.2 Test Applicability
7.7D.2.3 Minimum Conformance Requirements
7.7D.2.4 Test Description
7.7D.2.4.1 Initial Conditions
7.7D.2.4.2 Test Procedure
7.7D.2.4.3 Message Contents
7.7D.2.5 Test Requirement
7.7E Spurious response for UE category 0
7.7E.1 Test Purpose
7.7E.2 Test Applicability
7.7E.3 Minimum Conformance Requirements
7.7E.4 Test Description
7.7E.4.1 Initial Conditions
7.7E.4.2 Test Procedure
7.7E.4.3 Message Contents
7.7E.5 Test Requirement
7.7EA Spurious response for UE category M1
7.7EA.1 Test Purpose
7.7EA.2 Test Applicability
7.7EA.3 Minimum Conformance Requirements
7.7EA.4 Test Description
7.7EA.4.1 Initial Conditions
7.7EA.4.2 Test Procedure
7.7EA.4.3 Message Contents
7.7EA.5 Test Requirement
7.7EB Spurious response for UE Category 1bis
7.7EB.1 Test Purpose
7.7EB.2 Test Applicability
7.7EB.3 Minimum Conformance Requirements
7.7EB.4 Test Description
7.7EB.4.1 Initial Conditions
7.7EB.4.2 Test Procedure
7.7EB.4.3 Message Contents
7.7EB.5 Test Requirement
7.7F Spurious response for category NB1 and NB2
7.7F.1 Test purpose
7.7F.2 Test applicability
7.7F.3 Minimum conformance requirements
7.7F.4 Test description
7.7F.4.1 Initial conditions
7.7F.4.2 Test procedure
7.7F.4.3 Message contents
7.7F.5 Test requirement
7.7G Spurious response for V2X Communication
7.7G.1 Spurious response for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.7G.1.1 Test Purpose
7.7G.1.2 Test Applicability
7.7G.1.3 Minimum Conformance Requirements
7.7G.1.4 Test Description
7.7G.1.4.1 Initial Conditions
7.7G.1.4.2 Test Procedure
7.7G.1.4.3 Message Contents
7.7G.1.5 Test Requirement
7.7G.2 Spurious response for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.7G.2.1 Test Purpose
7.7G.2.2 Test applicability
7.7G.2.3 Minimum conformance requirements
7.7G.2.4 Test description
7.7G.2.4.1 Initial conditions
7.7G.2.4.2 Test Procedure
7.7G.2.4.3 Message Contents
7.7G.2.5 Test Requirement
7.7G.3 Spurious response for V2X Communication / Intra-band contiguous multi-carrier operation
7.7G.3.1 Test Purpose
7.7G.3.2 Test applicability
7.7G.3.3 Minimum conformance requirements
7.7G.3.4 Test description
7.7G.3.4.1 Initial conditions
7.7G.3.4.2 Test Procedure
7.7G.3.4.3 Message Contents
7.7G.3.5 Test Requirement
7.8 Intermodulation characteristics
7.8.1 Wide band Intermodulation
7.8.1.1 Test purpose
7.8.1.2 Test applicability
7.8.1.3 Minimum conformance requirements
7.8.1.4 Test description
7.8.1.4.1 Initial condition
7.8.1.4.2 Test procedure
7.8.1.4.3 Message contents
7.8.1.5 Test requirements
7.8.1_1 Wide band Intermodulation with 4 Rx antenna ports
7.8.1_1.1 Test purpose
7.8.1_1.2 Test applicability
7.8.1_1.3 Minimum conformance requirements
7.8.1_1.4 Test description
7.8.1_1.4.1 Initial condition
7.8.1_1.4.2 Test procedure
7.8.1_1.4.3 Message contents
7.8.1_1.5 Test requirements
7.8.1A Wide band Intermodulation for CA
7.8.1A.0 Minimum conformance requirements
7.8.1A.1 Wideband intermodulation for CA (intra-band contiguous DL CA and UL CA)
7.8.1A.1.1 Test purpose
7.8.1A.1.2 Test applicability
7.8.1A.1.3 Minimum conformance requirements
7.8.1A.1.4 Test description
7.8.1A.1.4.1 Initial condition
7.8.1A.1.4.2 Test procedure
7.8.1A.1.4.3 Message contents
7.8.1A.1.5 Test requirements
7.8.1A.2 Wideband intermodulation for CA (intra-band contiguous DL CA without UL CA)
7.8.1A.2.1 Test purpose
7.8.1A.2.2 Test applicability
7.8.1A.2.3 Minimum conformance requirements
7.8.1A.2.4 Test description
7.8.1A.2.4.1 Initial condition
7.8.1A.2.4.2 Test procedure
7.8.1A.2.4.3 Message contents
7.8.1A.2.5 Test requirements
7.8.1A.3 Wideband intermodulation for CA (inter-band DL CA without UL CA)
7.8.1A.3.1 Test purpose
7.8.1A.3.2 Test applicability
7.8.1A.3.3 Minimum conformance requirements
7.8.1A.3.4 Test description
7.8.1A.3.4.1 Initial condition
7.8.1A.3.4.2 Test procedure
7.8.1A.3.4.3 Message contents
7.8.1A.3.5 Test requirements
7.8.1A.4 Wideband intermodulation for CA (intra band non-contiguous DL CA without UL CA)
7.8.1A.4.1 Test purpose
7.8.1A.4.2 Test applicability
7.8.1A.4.3 Minimum conformance requirements
7.8.1A.4.4 Test description
7.8.1A.4.4.1 Initial condition
7.8.1A.4.4.2 Test procedure
7.8.1A.4.4.3 Message contents
7.8.1A.4.5 Test requirements
7.8.1A.5 Wideband intermodulation for 3DL CA
7.8.1A.5.1 Test purpose
7.8.1A.5.2 Test applicability
7.8.1A.5.3 Minimum conformance requirements
7.8.1A.5.4 Test description
7.8.1A.5.5 Test requirement
7.8.1A.6
7.8.1A.7 Wideband intermodulation for 4DL CA
7.8.1A.7.1 Test purpose
7.8.1A.7.2 Test applicability
7.8.1A.7.3 Minimum conformance requirements
7.8.1A.7.4 Test description
7.8.1A.7.5 Test requirement
7.8.1A.8 Wideband intermodulation for 5DL CA
7.8.1A.8.1 Test purpose
7.8.1A.8.2 Test applicability
7.8.1A.8.3 Minimum conformance requirements
7.8.1A.8.4 Test description
7.8.1A.8.5 Test requirement
7.8.1B Wide band Intermodulation for UL-MIMO
7.8.1B.1 Test purpose
7.8.1B.2 Test applicability
7.8.1B.3 Minimum conformance requirements
7.8.1B.4 Test description
7.8.1B.4.1 Initial condition
7.8.1B.4.2 Test procedure
7.8.1B.4.3 Message contents
7.8.1B.5 Test requirements
7.8.1C
7.8.1D Wide band intermodulation for ProSe
7.8.1D.0 Minimum conformance requirements
7.8.1D.1 Wide band intermodulation for ProSe Direct Discovery
7.8.1D.1.1 Test Purpose
7.8.1D.1.2 Test Applicability
7.8.1D.1.3 Minimum Conformance Requirements
7.8.1D.1.4 Test Description
7.8.1D.1.5 Test Requirement
7.8.1D.2 Wide band intermodulation for ProSe Direct Communication
7.8.1D.2.1 Test Purpose
7.8.1D.2.2 Test Applicability
7.8.1D.2.3 Minimum Conformance Requirements
7.8.1D.2.4 Test Description
7.8.1D.2.5 Test Requirement
7.8.1E Wide band Intermodulation for UE category 0
7.8.1E.1 Test purpose
7.8.1E.2 Test applicability
7.8.1E.3 Minimum conformance requirements
7.8.1E.4 Test description
7.8.1E.4.1 Initial condition
7.8.1E.4.2 Test procedure
7.8.1E.4.3 Message contents
7.8.1E.5 Test requirements
7.8.1EA Wide band Intermodulation for UE category M1
7.8.1EA.1 Test purpose
7.8.1EA.2 Test applicability
7.8.1EA.3 Minimum conformance requirements
7.8.1EA.4 Test description
7.8.1EA.4.1 Initial condition
7.8.1EA.4.2 Test procedure
7.8.1EA.4.3 Message contents
7.8.1EA.5 Test requirements
7.8.1EB Wide band Intermodulation for UE category 1bis
7.8.1EB.1 Test purpose
7.8.1EB.2 Test applicability
7.8.1EB.3 Minimum conformance requirements
7.8.1EB.4 Test description
7.8.1EB.4.1 Initial condition
7.8.1EB.4.2 Test procedure
7.8.1EB.4.3 Message contents
7.8.1EB.5 Test requirements
7.8.1EC Wide band intermodulation for UE category M2
7.8.1EC.1 Test purpose
7.8.1EC.2 Test applicability
7.8.1EC.3 Minimum conformance requirements
7.8.1EC.4 Test description
7.8.1EC.4.1 Initial conditions
7.8.1EC.4.2 Test procedure
7.8.1EC.4.3 Message contents
7.8.1EC.5 Test requirement
7.8.1F Wide band Intermodulation for category NB1 and NB2
7.8.1F.1 Test purpose
7.8.1F.2 Test applicability
7.8.1F.3 Minimum conformance requirements
7.8.1F.4 Test description
7.8.1F.4.1 Initial condition
7.8.1F.4.2 Test procedure
7.8.1F.4.3 Message contents
7.8.1F.5 Test requirements
7.8.1G Wide band Intermodulation for V2X Communication
7.8.1G.1 Wide band Intermodulation for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.8.1G.1.1 Test Purpose
7.8.1G.1.2 Test Applicability
7.8.1G.1.3 Minimum Conformance Requirements
7.8.1G.1.4 Test Description
7.8.1G.1.4.1 Initial Conditions
7.8.1G.1.4.2 Test Procedure
7.8.1G.1.4.3 Message Contents
7.8.1G.1.5 Test Requirement
7.8.1G.2 Wide band Intermodulation for V2X Communication / Simultaneous E-UTRA V2X sidelink and E-UTRA uplink transmissions
7.8.1G.2.1 Test Purpose
7.8.1G.2.2 Test Applicability
7.8.1G.2.3 Minimum Conformance Requirements
7.8.1G.2.4 Test Description
7.8.1G.2.4.1 Initial Conditions
7.8.1G.2.4.2 Test Procedure
7.8.1G.2.4.3 Message Contents
7.8.1G.2.5 Test Requirement
7.8.1G.3 Wide band Intermodulation for V2X Communication / Intra-band contiguous multi-carrier operation
7.8.1G.3.1 Test Purpose
7.8.1G.3.2 Test Applicability
7.8.1G.3.3 Minimum Conformance Requirements
7.8.1G.3.4 Test Description
7.8.1G.3.4.1 Initial Conditions
7.8.1G.3.4.2 Test Procedure
7.8.1G.3.4.3 Message Contents
7.8.1G.3.5 Test Requirement
7.8.2 Void
7.9 Spurious emissions
7.9.1 Test Purpose
7.9.2 Test Applicability
7.9.3 Minimum Conformance Requirements
7.9.4 Test Description
7.9.4.1 Initial Conditions
7.9.4.2 Test Procedure
7.9.4.3 Message Contents
7.9.5 Test Requirement
7.9_1 Spurious emissions with 4 Rx antenna ports
7.9_1.1 Test Purpose
7.9_1.2 Test Applicability
7.9_1.3 Minimum Conformance Requirements
7.9_1.4 Test Description
7.9_1.4.1 Initial Conditions
7.9_1.4.2 Test Procedure
7.9_1.4.3 Message Contents
7.9_1.5 Test Requirement
7.9A Spurious emissions for CA
7.9A.1 Test Purpose
7.9A.2 Test Applicability
7.9A.3 Minimum Conformance Requirements
7.9A.4 Test Description
7.9A.4.1 Initial Conditions
7.9A.4.2 Test Procedure
7.9A.4.3 Message Contents
7.9A.5 Test Requirement
7.9E Spurious emissions for UE category 0
7.9E.1 Test Purpose
7.9E.2 Test Applicability
7.9E.3 Minimum Conformance Requirements
7.9E.4 Test Description
7.9E.4.1 Initial Conditions
7.9E.4.2 Test Procedure
7.9E.4.3 Message Contents
7.9E.5 Test Requirement
7.9EA Spurious emissions for UE category M1
7.9EA.1 Test Purpose
7.9EA.2 Test Applicability
7.9EA.3 Minimum Conformance Requirements
7.9EA.4 Test Description
7.9EA.4.1 Initial Conditions
7.9EA.4.2 Test Procedure
7.9EA.4.3 Message Contents
7.9EA.5 Test Requirement
7.9EB Spurious emissions for UE Category 1bis
7.9EB.1 Test Purpose
7.9EB.2 Test Applicability
7.9EB.3 Minimum Conformance Requirements
7.9EB.4 Test Description
7.9EB.4.1 Initial Conditions
7.9EB.4.2 Test Procedure
7.9EB.4.3 Message Contents
7.9EB.5 Test Requirement
7.9F Spurious emissions for Category NB1
7.9F.1 Test Purpose
7.9F.2 Test Applicability
7.9F.3 Minimum Conformance Requirements
7.9F.4 Test Description
7.9F.4.1 Initial Conditions
7.9F.4.2 Test Procedure
7.9F.4.3 Message Contents
7.9F.5 Test Requirement
7.9G Spurious emissions for V2X Communication
7.9G.1 Spurious emissions for V2X Communication / Non-concurrent with E-UTRA uplink transmissions
7.9G.1.1 Test Purpose
7.9G.1.2 Test Applicability
7.9G.1.3 Minimum Conformance Requirements
7.9G.1.4 Test Description
7.9G.1.4.1 Initial Conditions
7.9G.1.4.2 Test Procedure
7.9G.1.4.3 Message Contents
7.9G.1.5 Test Requirement
7.10 Void
7.10A Receiver image for CA
8 Performance Requirement
8.1 General
8.1.1 Receiver antenna capability
8.1.1.1 Simultaneous unicast and MBMS operations
8.1.1.2 Dual-antenna receiver capability in idle mode
8.1.2 Applicability of requirements
8.1.2.1 Applicability of requirements for different channel bandwidths
8.1.2.2 Definition of CA capability
8.1.2.2A Definition of dual connectivity capability
8.1.2.3 Applicability and test rules for different CA configurations and bandwidth combination sets
8.1.2.3A Applicability and test rules for different dual connectivity configuration and bandwidth combination set
8.1.2.3B Applicability and test rules for different TDD-FDD CA configurations and bandwidth combination sets
8.1.2.3D Applicability and test rules for different CA with LAA SCell(s) configurations and bandwidth combination sets
8.1.2.4 Test coverage for different number of component carriers
8.1.2.6 Applicability of performance requirements for 4Rx capable UEs
8.1.2.6.1 Applicability rule and antenna connection for single carrier tests with 2Rx
8.1.2.6.2 Applicability rule and antenna connection for CA and DC tests with 2Rx
8.1.2.6.3 Applicability rule and antenna connection for single carrier tests with 4Rx
8.1.2.6.4 Applicability rule for 256QAM tests
8.1.2.6.5 Applicability rule and antenna connection for CA and DC tests with 4Rx
8.1.2.6.6 Applicability rule for Type C with 4Rx
8.1.2.7 Applicability of Enhanced Downlink Control Channel Performance Requirements
8.2 Demodulation of PDSCH (Cell-Specific Reference Symbols)
8.2.1 FDD (Fixed Reference Channel)
8.2.1.1 FDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)
8.2.1.1.1 FDD PDSCH Single Antenna Port Performance
8.2.1.1.1_1 FDD PDSCH Single Antenna Port Performance (Release 9 and forward)
8.2.1.1.1_2 FDD PDSCH Single Antenna Port Performance (Release 10 and forward)
8.2.1.1.1_A FDD PDSCH Single Antenna Port Performance for CA
8.2.1.1.1_A.1 FDD PDSCH Single Antenna Port Performance for CA (2DL CA)
8.2.1.1.1_A.2 FDD PDSCH Single Antenna Port Performance for CA (3DL CA)
8.2.1.1.1_A.3 Void
8.2.1.1.1_A.4 FDD PDSCH Single Antenna Port Performance for CA (4DL CA)
8.2.1.1.1_A.5 FDD PDSCH Single Antenna Port Performance for CA (5 DL CA)
8.2.1.1.2 FDD PDSCH Single Antenna Port Performance with 1 PRB in presence of MBSFN
8.2.1.2 FDD PDSCH Transmit Diversity Performance (Cell-Specific Reference Symbols)
8.2.1.2.1 FDD PDSCH Transmit Diversity 2x2
8.2.1.2.1_1 FDD PDSCH Transmit Diversity 2x2 (Release 9 and forward)
8.2.1.2.2 FDD PDSCH Transmit Diversity 4x2
8.2.1.2.2_1 FDD PDSCH Transmit Diversity 4x2 (Release 9 and forward)
8.2.1.2.3
8.2.1.2.3_C FDD PDSCH Transmit diversity 2x2 for eICIC
8.2.1.2.3_C.1 FDD PDSCH Transmit diversity 2x2 for eICIC (non-MBSFN ABS)
8.2.1.2.3_D
8.2.1.2.3_E FDD PDSCH Transmit diversity 2x2 for feICIC
8.2.1.2.3_E.1 FDD PDSCH Transmit diversity 2x2 for feICIC (non-MBSFN ABS)
8.2.1.2.4 FDD PDSCH Transmit Diversity 2x2 with TM3 Interference Model ΠEnhanced Performance Requirement Type A
8.2.1.2.5 FDD PDSCH Transmit Diversity 2x2 with TM2 Interference Model ΠEnhanced Performance Requirement Type B
8.2.1.2.6 FDD PDSCH Transmit Diversity 2x2 with TM9 Interference Model ΠEnhanced Performance Requirement Type B
8.2.1.3 FDD PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)
8.2.1.3.1 FDD PDSCH Open Loop Spatial Multiplexing 2x2
8.2.1.3.1_1 FDD PDSCH Open Loop Spatial Multiplexing 2x2 (Release 11 and forward)
8.2.1.3.1_A FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA
8.2.1.3.1_A.1 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (2DL CA)
8.2.1.3.1_A.2 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (3DL CA)
8.2.1.3.1_A.3 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (4DL CA)
8.2.1.3.1_A.4 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (5DL CA)
8.2.1.3.1A FDD Soft buffer management test
8.2.1.3.1A_A.1 FDD PDSCH Soft buffer management test for CA (2 DL CA)
8.2.1.3.1A_A.2 Void
8.2.1.3.1B FDD PDSCH Open Loop Spatial Multiplexing 2x2 ΠEnhanced Performance Requirement Type C
8.2.1.3.1B.1 Test purpose
8.2.1.3.1B.2 Test applicability
8.2.1.3.1B.3 Minimum conformance requirements
8.2.1.3.1B.4 Test description
8.2.1.3.1B.4.1 Initial conditions
8.2.1.3.1B.4.2 Test procedure
8.2.1.3.1B.4.3 Message contents
8.2.1.3.1B.5 Test requirement
8.2.1.3.1C.1 Test purpose
8.2.1.3.1C.2 Test applicability
8.2.1.3.1C.3 Minimum conformance requirements
8.2.1.3.1C.4 Test description
8.2.1.3.1C.4.1 Initial conditions
8.2.1.3.1C.4.2 Test procedure
8.2.1.3.1C.4.3 Message contents
8.2.1.3.1C.5 Test requirement
8.2.1.3.2 FDD PDSCH Open Loop Spatial Multiplexing 4x2
8.2.1.3.3_C FDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC
8.2.1.3.3_C.1 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (non-MBSFN ABS)
8.2.1.3.3_C.2 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (MBSFN ABS)
8.2.1.3.3_D
8.2.1.3.3_E FDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC
8.2.1.3.3_E.1 FDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC (demodulation subframe overlaps with aggressor cell ABS a
8.2.1.4 FDD PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)
8.2.1.4.1 FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2
8.2.1.4.1_1 FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 (Release 9 and forward)
8.2.1.4.1_A to D
8.2.1.4.1_E FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC
8.2.1.4.1_E.1 FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC (non-MBSFN ABS)
8.2.1.4.1_H FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 for 256QAM in DL
8.2.1.4.2A FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 ΠEnhanced Performance Requirement Type C
8.2.1.4.2 FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2
8.2.1.4.2_1 FDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2 (Release 9 and forward)
8.2.1.4.2_A FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA
8.2.1.4.2_A.1 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (2DL CA)
8.2.1.4.2_A.2 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (3DL CA)
8.2.1.4.2_A.3 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (4DL CA)
8.2.1.4.2_A.4 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (5DL CA)
8.2.1.4.3 FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model ΠEnhanced Performance Requir
8.2.1.4.3A FDD PDSCH Closed Loop Multi-Layer Spatial Multiplexing 4x2 for Dual Connectivity
8.2.1.4.4 FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model ΠEnhanced Performance Requir
8.2.1.5
8.2.1.6
8.2.1.7 Carrier aggregation with power imbalance
8.2.1.7_A.1 FDD Carrier aggregation with power imbalance (intra-band contiguous DL CA)
8.2.1.8 FFS
8.2.1.9 FDD PDSCH performance in HST-SFN scenario
8.2.1.9.1 Test purpose
8.2.1.9.2 Test applicability
8.2.1.9.3 Minimum conformance requirements
8.2.1.9.4 Test description
8.2.1.9.5 Test requirement
8.2.2 TDD (Fixed Reference Channel)
8.2.2.1 TDD PDSCH Single Antenna Port Performance (Cell-Specific Reference Symbols)
8.2.2.1.1 TDD PDSCH Single Antenna Port Performance
8.2.2.1.1_1 TDD PDSCH Single Antenna Port Performance (Release 9 and forward)
8.2.2.1.1_2 TDD PDSCH Single Antenna Port Performance (Release 10 and forward)
8.2.2.1.1_A TDD PDSCH Single Antenna Port Performance for CA
8.2.2.1.1_A.1 TDD PDSCH Single Antenna Port Performance for CA (2DL CA)
8.2.2.1.1_A.2 TDD PDSCH Single Antenna Port Performance for CA (3DL CA)
8.2.2.1.1_A.3 TDD PDSCH Single Antenna Port Performance for CA (4DL CA)
8.2.2.1.1_A.4 TDD PDSCH Single Antenna Port Performance for CA (5DL CA)
8.2.2.1.2 TDD PDSCH Single Antenna Port Performance with 1 PRB in the presence of MBSFN
8.2.2.2 TDD PDSCH Transmit Diversity Performance (Cell-Specific Reference Symbols)
8.2.2.2.1 TDD PDSCH Transmit Diversity 2x2
8.2.2.2.1_1 TDD PDSCH Transmit Diversity 2x2 (Release 9 and forward)
8.2.2.2.2 TDD PDSCH Transmit Diversity 4x2
8.2.2.2.2_1 TDD PDSCH Transmit Diversity 4x2 (Release 9 and forward)
8.2.2.2.3_C TDD PDSCH Transmit diversity 2x2 for eICIC
8.2.2.2.3_C.1 TDD PDSCH Transmit diversity 2x2 for eICIC (non-MBSFN ABS)
8.2.2.2.3_D
8.2.2.2.3_E TDD PDSCH Transmit diversity 2x2 for feICIC
8.2.2.2.3_E.1 TDD PDSCH Transmit diversity 2x2 for feICIC (non-MBSFN ABS)
8.2.2.2.4 TDD PDSCH Transmit Diversity 2x2 with TM3 Interference Model ΠEnhanced Performance Requirement Type A
8.2.2.2.5 TDD PDSCH Transmit Diversity 2x2 for eIMTA(when EIMTA-MainConfigServCell-r12 is configured)
8.2.2.2.6 TDD PDSCH Transmit Diversity 2x2 with TM2 Interference Model ΠEnhanced Performance Requirement Type B
8.2.2.2.7 TDD PDSCH Transmit Diversity 2x2 with TM9 Interference Model ΠEnhanced Performance Requirement Type B
8.2.2.3 TDD PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)
8.2.2.3.1 TDD PDSCH Open Loop Spatial Multiplexing 2x2
8.2.2.3.1_1 TDD PDSCH Open Loop Spatial Multiplexing 2x2 (Release 11 and forward)
8.2.2.3.1_A TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA
8.2.2.3.1_A.1 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (2DL CA)
8.2.2.3.1_A.2 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (3DL CA)
8.2.2.3.1_A.3 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (4DL CA)
8.2.2.3.1_A.4 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for CA (5DL CA)
8.2.2.3.1A TDD Soft buffer management test
8.2.2.3.1A_A.1 TDD PDSCH Soft buffer management test for CA (2 DL CA)
8.2.2.3.1A_A.2 Void
8.2.2.3.1A_A.3 Void
8.2.2.3.1B TDD PDSCH Open Loop Spatial Multiplexing 2x2 - Enhanced Performance Requirement Type C
8.2.2.3.1B.1 Test purpose
8.2.2.3.1B.2 Test applicability
8.2.2.3.1B.3 Minimum conformance requirements
8.2.2.3.1B.4 Test description
8.2.2.3.1B.5 Test requirement
8.2.2.3.1C.1 Test purpose
8.2.2.3.1C.2 Test applicability
8.2.2.3.1C.3 Minimum conformance requirements
8.2.2.3.1C.4 Test description
8.2.2.3.1C.4.1 Initial conditions
8.2.2.3.1C.4.2 Test procedure
8.2.2.3.1C.4.3 Message contents
8.2.2.3.1C.5 Test requirement
8.2.2.3.2 TDD PDSCH Open Loop Spatial Multiplexing 4x2
8.2.2.3.3_C TDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC
8.2.2.3.3_C.1 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (non-MBSFN ABS)
8.2.2.3.3_C.2 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for eICIC (MBSFN ABS)
8.2.2.3.3_D
8.2.2.3.3_E TDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC
8.2.2.3.3_E.1 TDD PDSCH Open Loop Spatial Multiplexing 2x2 for feICIC (demodulation subframe overlaps with aggressor cell ABS a
8.2.2.4 TDD PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)
8.2.2.4.1 TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2
8.2.2.4.1_1 TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 (Release 9 and forward)
8.2.2.4.1_A to D
8.2.2.4.1_E TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC
8.2.2.4.1_E.1 TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 2x2 for feICIC (non-MBSFN ABS)
8.2.2.4.1_H TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 for 256QAM in DL
8.2.2.4.2 TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2
8.2.2.4.2_1 TDD PDSCH Closed Loop Single/Multi Layer Spatial Multiplexing 4x2 (Release 9 and forward)
8.2.2.4.2_A TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA
8.2.2.4.2_A.1 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (2DL CA)
8.2.2.4.2_A.2 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (3DL CA)
8.2.2.4.2_A.3 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (4DL CA)
8.2.2.4.2_A.4 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for CA (5DL CA)
8.2.2.4.2A TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 2x2 ΠEnhanced Performance Requirement Type C
8.2.2.4.3 TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model ΠEnhanced Performance Requir
8.2.2.4.4 TDD PDSCH Closed Loop Multi-Layer Spatial Multiplexing 4x2 for Dual Connectivity
8.2.2.4.5 TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x2 with TM4 Interference Model ΠEnhanced Performance Requir
8.2.2.5
8.2.2.6
8.2.2.7 Carrier aggregation with power imbalance
8.2.2.7_A.1 TDD Carrier aggregation with power imbalance (intra-band contiguous DL CA)
8.2.2.8 FFS
8.2.2.9 TDD PDSCH HST-SFN performance in HST-SFN scenario
8.2.3 TDD FDD CA (Fixed Reference Channel)
8.2.3.1 TDD FDD CA PDSCH Single Antenna Port Performance
8.2.3.1.1.1 TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (2DL CA)
8.2.3.1.1.2 TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (3DL CA)
8.2.3.1.1.3 TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (4DL CA)
8.2.3.1.1.4 TDD FDD CA PDSCH Single Antenna Port Performance for FDD PCell (5DL CA)
8.2.3.1.2.1 TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (2DL CA)
8.2.3.1.2.2 TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (3DL CA)
8.2.3.1.2.3 TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (4DL CA)
8.2.3.1.2.4 TDD FDD CA PDSCH Single Antenna Port Performance for TDD PCell (5DL CA)
8.2.3.2 TDD FDD CA PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)
8.2.3.2.1 TDD FDD CA PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols) for FDD PCell
8.2.3.2.1.1 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (2DL CA)
8.2.3.2.1.2 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (3DL CA)
8.2.3.2.1A TDD FDD CA PDSCH Soft buffer management test for FDD PCell (2DL CA)
8.2.3.2.1.3 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (4DL CA)
8.2.3.2.1.4 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for FDD PCell (5DL CA)
8.2.3.2.2 TDD FDD CA PDSCH Open Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols) for TDD PCell
8.2.3.2.2.1 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (2DL CA)
8.2.3.2.2.2 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (3DL CA)
8.2.3.2.2.3 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (4DL CA)
8.2.3.2.2.4 TDD FDD CA PDSCH Open Loop Spatial Multiplexing 2x2 for TDD PCell (5DL CA)
8.2.3.2.2A TDD FDD CA PDSCH Soft buffer management test for TDD PCell (2DL CA)
8.2.3.3 TDD FDD CA PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols)
8.2.3.3.1 TDD FDD CA PDSCH Closed Loop Spatial Multiplexing Performance (Cell-Specific Reference Symbols) for FDD PCell
8.2.3.3.1.1 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (2DL CA)
8.2.3.3.1.2 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (3DL CA)
8.2.3.3.1.3 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (4DL CA)
8.2.3.3.1.4 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for FDD PCell (5DL CA)
8.2.3.3.2 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell
8.2.3.3.2.1 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (2DL CA)
8.2.3.3.2.2 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (3DL CA)
8.2.3.3.2.3 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (4DL CA)
8.2.3.3.2.4 TDD FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x2 for TDD PCell (5DL CA)
8.2.4 LAA
8.2.4.1 LAA PDSCH CA Closed-Loop Spatial Multiplexing Performance
8.2.4.1.1 LAA PDSCH CA Closed Loop Spatial Multiplexing Performance with 4 Tx Antenna port and with FDD as Pcell (FDD single ca
8.2.4.1.1.1 Test purpose
8.2.4.1.1.2 Test applicability
8.2.4.1.1.3 Minimum conformance requirements
8.2.4.1.1.4 Test description
8.2.4.1.1.5 Test requirement
8.2.4.1.2 LAA PDSCH CA Closed Loop Spatial Multiplexing Performance with 4 Tx Antenna port and with TDD as Pcell (TDD single ca
8.2.4.1.2.1 Test purpose
8.2.4.1.2.2 Test applicability
8.2.4.1.2.3 Minimum conformance requirements
8.2.4.1.2.4 Test description
8.2.4.1.2.5 Test requirement
8.3 Demodulation of PDSCH (User-Specific Reference Symbols)
8.3.1 FDD
8.3.1.1 FDD PDSCH Single-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)
8.3.1.1.1_D FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIM
8.3.1.1.1_D.1 Test purpose
8.3.1.1.1_D.2 Test applicability
8.3.1.1.1_D.3 Minimum conformance requirements
8.3.1.1.1_D.4 Test description
8.3.1.1.1_D.5 Test requirement
8.3.1.1.1_H FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIM
8.3.1.1.1_H.1 Test purpose
8.3.1.1.1_H.2 Test applicability
8.3.1.1.1_H.3 Minimum conformance requirements
8.3.1.1.1_H.4 Test description
8.3.1.1.2_D FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with a simultaneous transmission for eDL-MIMO
8.3.1.1.2_D.1 Test purpose
8.3.1.1.2_D.2 Test applicability
8.3.1.1.2_D.3 Minimum conformance requirements
8.3.1.1.2_D.4 Test description
8.3.1.1.3 FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performanc
8.3.1.1.3.1 Test purpose
8.3.1.1.3.2 Test applicability
8.3.1.1.3.3 Minimum conformance requirements
8.3.1.1.3.4 Test description
8.3.1.1.4 FDD PDSCH Closed Loop Single Layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model ΠEnhance
8.3.1.1.5 FDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with CRS Interference Model - Enhance
8.3.1.1.6 FDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM3 interference model - Enhance
8.3.1.1.7 FDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM10 serving cell configuration
8.3.1.1.7.1 Test purpose
8.3.1.1.7.2 Test applicability
8.3.1.1.7.3 Minimum conformance requirements
8.3.1.1.7.4 Test description
8.3.1.1.8
8.3.1.1.9 FDD PDSCH Single-layer Spatial Multiplexing for FD-MIMO
8.3.1.1.9.1 Test purpose
8.3.1.1.9.2 Test applicability
8.3.1.1.9.3 Minimum conformance requirements
8.3.1.1.9.4 Test description
8.3.1.1.9.5 Test requirement
8.3.1.2 FDD PDSCH Dual-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)
8.3.1.2.1_D FDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO
8.3.1.2.1_D.1 Test purpose
8.3.1.2.1_D.2 Test applicability
8.3.1.2.1_D.3 Minimum conformance requirements
8.3.1.2.1_D.4 Test description
8.3.1.2.1_D.4.2 Test procedure
8.3.1.2.1_D.4.3 Message contents
8.3.1.2.1_D.5 Test requirement
8.3.1.2.1_D_1 FDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO (Release 11 and forward)
8.3.1.2.1_D_1.1 Test purpose
8.3.1.2.1_D_1.2 Test applicability
8.3.1.2.1_D_1.3 Minimum conformance requirements
8.3.1.2.1_D_1.4 Test description
8.3.1.2.1_D_1.4.2 Test procedure
8.3.1.2.1_D_1.4.3 Message contents
8.3.1.2.1_D_1.5 Test requirement
8.3.1.2.2 FDD PDSCH Dual-layer Spatial Multiplexing ΠEnhanced Performance Requirement Type C
8.3.1.2.2.1 Test purpose
8.3.1.2.2.2 Test applicability
8.3.1.2.2.3 Minimum conformance requirements
8.3.1.2.2.4 Test description
8.3.1.2.2.4.1 Initial conditions
8.3.1.2.2.4.2 Test procedure
8.3.1.2.2.4.3 Message contents
8.3.1.2.2.5 Test requirement
8.3.1.3 FDD PDSCH Performance with DCI format 2D and non Quasi Co-located Antenna Ports
8.3.1.3.1_F FDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and single NZP CSI-RS re
8.3.1.3.1_F.1 Test purpose
8.3.1.3.1_F.2 Test applicability
8.3.1.3.1_F.3 Minimum conformance requirements
8.3.1.3.1_F.4 Test description
8.3.1.3.1_F.4.1 Initial conditions
8.3.1.3.1_F.4.2 Test procedure
8.3.1.3.1_F.4.3 Message contents
8.3.1.3.1_F.5 Test requirement
8.3.1.3.2_F FDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and multiple NZP CSI-RS
8.3.1.3.2_F.1 Test purpose
8.3.1.3.2_F.2 Test applicability
8.3.1.3.2_F.3 Minimum conformance requirements
8.3.1.3.2_F.4 Test description
8.3.1.3.2_F.4.1 Initial conditions
8.3.1.3.2_F.4.2 Test procedure
8.3.1.3.2_F.4.3 Message contents
8.3.1.3.2_F.5 Test requirements
8.3.1.3.3_F FDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Different Cell ID, Colliding CRS and
8.3.1.3.3_F.1 Test purpose
8.3.1.3.3_F.2 Test applicability
8.3.1.3.3_F.3 Minimum conformance requirements
8.3.1.3.3_F.4 Test description
8.3.1.3.3_F.4.1 Initial conditions
8.3.1.3.3_F.4.2 Test procedure
8.3.1.3.3_F.4.3 Message contents
8.3.1.3.3_F.5 Test requirements
8.3.2 TDD
8.3.2.1 TDD PDSCH Single-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)
8.3.2.1.1 TDD PDSCH Single-layer Spatial Multiplexing on antenna port 5 (Release 8 and forward)
8.3.2.1.1_1 TDD PDSCH Single-layer Spatial Multiplexing on antenna port 5 (Release 9 and forward)
8.3.2.1.2 TDD PDSCH Single-layer Spatial Multiplexing on antenna port 7 or 8 without a simultaneous transmission
8.3.2.1.2_D TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIM
8.3.2.1.2_H TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 without a simultaneous transmission for eDL-MIM
8.3.2.1.3 TDD PDSCH Single-layer Spatial Multiplexing on antenna port 7 or 8 with a simultaneous transmission
8.3.2.1.3_D TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with a simultaneous transmission for eDL-MIMO
8.3.2.1.4 TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Performanc
8.3.2.1.4.1 Test purpose
8.3.2.1.4.2 Test applicability
8.3.2.1.4.3 Minimum conformance requirements
8.3.2.1.4.4 Test description
8.3.2.1.4.5 Test requirement
8.3.2.1.5 TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM9 Interference Model - Enhance
8.3.2.1.6 TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with CRS Interference Model - Enhance
8.3.2.1.7 TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM3 Interference Model - Enhance
8.3.2.1.8 TDD PDSCH Closed Loop Single-layer Spatial Multiplexing on antenna ports 7 or 8 with TM10 serving cell configuration
8.3.2.1.8.1 Test purpose
8.3.2.1.8.2 Test applicability
8.3.2.1.8.3 Minimum conformance requirements
8.3.2.1.8.4 Test description
8.3.2.1.9
8.3.2.1.10 TDD PDSCH Single-layer Spatial Multiplexing for FD-MIMO
8.3.2.1.10.1 Test purpose
8.3.2.1.10.2 Test applicability
8.3.2.1.10.3 Minimum conformance requirements
8.3.2.1.10.4 Test description
8.3.2.1.10.5 Test requirement
8.3.2.2 TDD PDSCH Dual-layer Spatial Multiplexing Performance (UE-Specific Reference Symbols)
8.3.2.2.1 TDD PDSCH Dual-layer Spatial Multiplexing
8.3.2.2.1_D TDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO
8.3.2.2.1_D.1 Test purpose
8.3.2.2.1_D.2 Test applicability
8.3.2.2.1_D.3 Minimum conformance requirements
8.3.2.2.1_D.4 Test description
8.3.2.2.1_D.4.2 Test procedure
8.3.2.2.1_D.4.3 Message contents
8.3.2.2.1_D.5 Test requirement
8.3.2.2.1_D_1 TDD PDSCH Dual-layer Spatial Multiplexing for eDL-MIMO (Release 11 and forward)
8.3.2.2.1_D_1.1 Test purpose
8.3.2.2.1_D_1.2 Test applicability
8.3.2.2.1_D_1.3 Minimum conformance requirements
8.3.2.2.1_D_1.4 Test description
8.3.2.2.1_D_1.4.2 Test procedure
8.3.2.2.1_D_1.4.3 Message contents
8.3.2.2.1_D_1.5 Test requirement
8.3.2.2.2 TDD PDSCH Dual-layer Spatial Multiplexing ΠEnhanced Performance Requirement Type C
8.3.2.2.2.1 Test purpose
8.3.2.2.2.2 Test applicability
8.3.2.2.2.3 Minimum conformance requirements
8.3.2.2.2.4 Test description
8.3.2.2.2.4.1 Initial conditions
8.3.2.2.2.4.2 Test procedure
8.3.2.1.2.4.3 Message contents
8.3.2.2.2.5 Test requirement
8.3.2.3 Dual-Layer Spatial Multiplexing (with multiple CSI-RS configurations)
8.3.2.4 TDD PDSCH Performance with DCI format 2D and non Quasi Co-located Antenna Ports
8.3.2.4.1_F TDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and single NZP CSI-RS re
8.3.2.4.1_F.1 Test purpose
8.3.2.4.1_F.2 Test applicability
8.3.2.4.1_F.3 Minimum conformance requirements
8.3.2.4.1_F.4 Test description
8.3.2.4.1_F.4.1 Initial conditions
8.3.2.4.1_F.4.2 Test procedure
8.3.2.4.1_F.4.3 Message contents
8.3.2.4.1_F.5 Test requirement
8.3.2.4.2_F TDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Same Cell ID and multiple NZP CSI-RS
8.3.2.4.2_F.1 Test purpose
8.3.2.4.2_F.2 Test applicability
8.3.2.4.2_F.3 Minimum conformance requirements
8.3.2.4.2_F.4 Test description
8.3.2.4.2_F.4.1 Initial conditions
8.3.2.4.2_F.4.2 Test procedure
8.3.2.4.2_F.4.3 Message contents
8.3.2.4.2_F.5 Test requirements
8.3.2.4.3_F TDD PDSCH Performance with DCI format 2D, non Quasi Co-located Antenna Ports, Different Cell ID, Colliding CRS and
8.3.2.4.3_F.1 Test purpose
8.3.2.4.3_F.2 Test applicability
8.3.2.4.3_F.3 Minimum conformance requirements
8.3.2.4.3_F.4 Test description
8.3.2.4.3_F.4.1 Initial conditions
8.3.2.4.3_F.4.2 Test procedure
8.3.2.4.3_F.4.3 Message contents
8.3.2.4.3_F.5 Test requirements
8.3.3 LAA
8.3.3.1 Dual-Layer Spatial Multiplexing with DM-RS
8.3.3.1.1 LAA Dual-Layer Spatial Multiplexing with DM-RS with FDD as PCell
8.3.3.1.1.1 Test purpose
8.3.3.1.1.2 Test applicability
8.3.3.1.1.3 Minimum conformance requirements
8.3.3.1.1.4 Test description
8.3.3.1.1.4.1 Initial conditions
8.3.3.1.1.4.2 Test procedure
8.3.3.1.1.4.3 Message contents
8.3.3.1.1.5 Test Requirements
8.3.3.1.2 LAA Dual-Layer Spatial Multiplexing with DM-RS with TDD as PCell
8.3.3.1.2.1 Test purpose
8.3.3.1.2.2 Test applicability
8.3.3.1.2.3 Minimum conformance requirements
8.3.3.1.2.4 Test description
8.3.3.1.2.4.1 Initial conditions
8.3.3.1.2.4.2 Test procedure
8.3.3.1.2.4.3 Message contents
8.3.3.1.2.5 Test Requirements
8.4 Demodulation of PCFICH/PDCCH
8.4.1 FDD
8.4.1.1 FDD PCFICH/PDCCH Single-antenna Port Performance
8.4.1.1.1 Test purpose
8.4.1.1.2 Test applicability
8.4.1.1.3 Minimum conformance requirements
8.4.1.1.4 Test description
8.4.1.1.5 Test requirement
8.4.1.2 FDD PCFICH/PDCCH Transmit Diversity Performance
8.4.1.2.1 FDD PCFICH/PDCCH Transmit Diversity 2x2
8.4.1.2.1_1 FDD PCFICH/PDCCH Transmit Diversity 2x2 (Release 9 and forward)
8.4.1.2.2 FDD PCFICH/PDCCH Transmit Diversity 4x2
8.4.1.2.2_1 FDD PCFICH/PDCCH Transmit Diversity 4x2 (Release 9 and forward)
8.4.1.2.3
8.4.1.2.3_C FDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC
8.4.1.2.3_C.1 FDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)
8.4.1.2.3_C.2 FDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (MBSFN ABS)
8.4.1.2.3_D
8.4.1.2.3_E FDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC
8.4.1.2.3_E.1 FDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)
8.4.1.2.3_E.2 FDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (MBSFN ABS)
8.4.1.2.4
8.4.1.2.5 FDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port under Asynch
8.4.1.2.6 FDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Col
8.4.1.2.7 FDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Collidi
8.4.1.2.8 FDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Col
8.4.2 TDD
8.4.2.1 TDD PCFICH/PDCCH Single-antenna Port Performance
8.4.2.1.1 Test purpose
8.4.2.1.2 Test applicability
8.4.2.1.3 Minimum conformance requirements
8.4.2.1.4 Test description
8.4.2.1.5 Test requirement
8.4.2.2 TDD PCFICH/PDCCH Transmit Diversity Performance
8.4.2.2.1 TDD PCFICH/PDCCH Transmit Diversity 2x2
8.4.2.2.1_1 TDD PCFICH/PDCCH Transmit Diversity 2x2 (Release 9 and forward)
8.4.2.2.2 TDD PCFICH/PDCCH Transmit Diversity 4x2
8.4.2.2.2_1 TDD PCFICH/PDCCH Transmit Diversity 4x2 (Release 9 and forward)
8.4.2.2.3_C TDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC
8.4.2.2.3_C.1 TDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)
8.4.2.2.3_C.2 TDD PCFICH/PDCCH Transmit Diversity 2x2 for eICIC (MBSFN ABS)
8.4.2.2.3_D
8.4.2.2.3_E TDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC
8.4.2.2.3_E.1 TDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)
8.4.2.2.3_E.2 TDD PCFICH/PDCCH Transmit Diversity 2x2 for feICIC (MBSFN ABS)
8.4.2.2.4
8.4.2.2.5 TDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port with Collidi
8.4.2.2.6 TDD Enhanced Downlink Control Channel Performance Requirement Type A for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Col
8.4.2.2.7 TDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Collidi
8.4.2.2.8 TDD Enhanced Downlink Control Channel Performance Requirement Type B for PCFICH/PDCCH, 2 Tx Antenna Port with Non-Col
8.4.3 LAA
8.4.3.1 Transmit Diversity Performance
8.4.3.1.1 LAA PCFICH/PDCCH Transmit Diversity 2x2 with FDD as Pcell
8.4.3.1.2 LAA PCFICH/PDCCH Transmit Diversity 2x2 with TDD as Pcell
8.5 Demodulation of PHICH
8.5.1 FDD
8.5.1.1 FDD PHICH Single-antenna Port Performance
8.5.1.1.1 Test purpose
8.5.1.1.2 Test applicability
8.5.1.1.3 Minimum conformance requirements
8.5.1.1.4 Test description
8.5.1.1.5 Test requirement
8.5.1.2 FDD PHICH Transmit Diversity Performance
8.5.1.2.1 FDD PHICH Transmit Diversity 2x2
8.5.1.2.1_1 FDD PHICH Transmit Diversity 2x2 (Release 9 and forward)
8.5.1.2.2 FDD PHICH Transmit Diversity 4x2
8.5.1.2.2_1 FDD PHICH Transmit Diversity 4x2 (Release 9 and forward)
8.5.1.2.3
8.5.1.2.3_A
8.5.1.2.3_B
8.5.1.2.3_C FDD PHICH Transmit Diversity 2x2 for eICIC
8.5.1.2.3_C.1 FDD PHICH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)
8.5.1.2.3_D
8.5.1.2.3_E FDD PHICH Transmit Diversity 2x2 for feICIC
8.5.1.2.3_E.1 FDD PHICH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)
8.5.1.2.4
8.5.1.2.5 FDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH- 2 Tx Antenna Ports under Asynchronous
8.5.1.2.6 FDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH - 2 Tx Antenna Ports with Non-Collidin
8.5.1.2.7 FDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH - 2 Tx Antenna Ports with Colliding CR
8.5.1.2.8 FDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH - 2 Tx Antenna Ports with Non-Collidin
8.5.2 TDD
8.5.2.1 TDD PHICH Single-antenna Port Performance
8.5.2.1.1 Test purpose
8.5.2.1.2 Test applicability
8.5.2.1.3 Minimum conformance requirements
8.5.2.1.4 Test description
8.5.2.1.5 Test requirement
8.5.2.2 TDD PHICH Transmit Diversity Performance
8.5.2.2.1 TDD PHICH Transmit Diversity 2x2
8.5.2.2.1_1 TDD PHICH Transmit Diversity 2x2 (Release 9 and forward)
8.5.2.2.2 TDD PHICH Transmit Diversity 4x2
8.5.2.2.2_1 TDD PHICH Transmit Diversity 4x2 (Release 9 and forward)
8.5.2.2.3
8.5.2.2.3_A
8.5.2.2.3_B
8.5.2.2.3_C TDD PHICH Transmit Diversity 2x2 for eICIC
8.5.2.2.3_C.1 TDD PHICH Transmit Diversity 2x2 for eICIC (non-MBSFN ABS)
8.5.2.2.3_D
8.5.2.2.3_E TDD PHICH Transmit Diversity 2x2 for feICIC
8.5.2.2.3_E.1 TDD PHICH Transmit Diversity 2x2 for feICIC (non-MBSFN ABS)
8.5.2.2.4
8.5.2.2.5 TDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH- 2 Tx Antenna Ports with Colliding CRS
8.5.2.2.6 TDD Enhanced Downlink Control Channel Performance Requirement Type A for PHICH - 2 Tx Antenna Ports with Non-Collidin
8.5.2.2.7 TDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH- 2 Tx Antenna Ports with Colliding CRS
8.5.2.2.8 TDD Enhanced Downlink Control Channel Performance Requirement Type B for PHICH- 2 Tx Antenna Ports with Non-Colliding
8.6 Demodulation of PBCH
8.7 Sustained downlink data rate provided by lower layers
8.7.1 FDD
8.7.1.1 FDD sustained data rate performance
8.7.1.1.1 Test purpose
8.7.1.1.2 Test applicability
8.7.1.1.3 Minimum requirements
8.7.1.1.4 Test description
8.7.1.1.5 Test requirement
8.7.1.1_1 FDD sustained data rate performance (Rel-10 and forward)
8.7.1.1_1.1 Test purpose
8.7.1.1_1.2 Test applicability
8.7.1.1_1.3 Minimum requirements
8.7.1.1_1.4 Test description
8.7.1.1_1.5 Test requirement
8.7.1.1_2 FDD sustained data rate performance for UE category 1bis
8.7.1.1_A FDD sustained data rate performance for CA
8.7.1.1_A.1 FDD Sustained data rate performance for CA (2DL CA)
8.7.1.1_A.2 FDD Sustained data rate performance for CA (3DL CA)
8.7.1.1_A.3 Void
8.7.1.1_A.4 FDD Sustained data rate performance for CA (4DL CA)
8.7.1.1_A.5 FDD Sustained data rate performance for CA (5DL CA)
8.7.1.1_H FDD sustained data rate performance for 256QAM in DL
8.7.1.1_H.1 FDD sustained data rate performance for 256QAM in DL (Single Carrier)
8.7.1.1_H.1.1 Test purpose
8.7.1.1_H.1.2 Test applicability
8.7.1.1_H.1.3 Minimum requirements
8.7.1.1_H.1.4 Test description
8.7.1.1_H.1.5 Test requirement
8.7.1.1_H.2 FDD Sustained data rate performance for CA (2DL CA) for 256QAM in DL
8.7.1.1_H.3 FDD Sustained data rate performance for CA for 256QAM in DL (3DL CA)
8.7.1.1_H.4 FDD Sustained data rate performance for CA (4DL CA) for 256QAM in DL
8.7.1.1_H.5 FDD Sustained data rate performance for CA (5DL CA) for 256QAM in DL
8.7.2 TDD
8.7.2.1 TDD sustained data rate performance
8.7.2.1.1 Test purpose
8.7.2.1.2 Test applicability
8.7.2.1.3 Minimum requirements
8.7.2.1.4 Test description
8.7.2.1.5 Test requirement
8.7.2.1_1 TDD sustained data rate performance (Rel-10 and forward)
8.7.2.1_1.1 Test purpose
8.7.2.1_1.2 Test applicability
8.7.2.1_1.3 Minimum requirements
8.7.2.1_1.4 Test description
8.7.2.1_1.5 Test requirement
8.7.2.1_2 TDD sustained data rate performance for UE category 1bis
8.7.2.1_A TDD sustained data rate performance for CA
8.7.2.1_A.1 TDD sustained data rate performance for CA (2DL CA)
8.7.2.1_A.2 TDD Sustained data rate performance for CA (3DL CA)
8.7.2.1_A.3 TDD Sustained data rate performance for CA (4DL CA)
8.7.2.1_A.4 Void
8.7.2.1_A.5 TDD Sustained data rate performance for CA (5DL CA)
8.7.2.1_A.5.1 Test purpose
8.7.2.1_A.5.2 Test applicability
8.7.2.1_A.5.3 Minimum conformance requirements
8.7.2.1_A.5.4 Test description
8.7.2.1_A.5.4.1 Initial conditions
8.7.2.1_A.5.4.2 Test procedure
8.7.2.1_A.5.4.3 Message contents
8.7.2.1_A.5.5 Test requirement
8.7.2.1_H TDD sustained data rate performance for 256QAM in DL
8.7.2.1_H.1 TDD sustained data rate performance for 256QAM in DL (Single Carrier)
8.7.2.1_H.1.1 Test purpose
8.7.2.1_H.1.2 Test applicability
8.7.2.1_H.1.3 Minimum requirements
8.7.2.1_H.1.4 Test description
8.7.2.1_H.1.5 Test requirement
8.7.2.1_H.2 TDD sustained data rate performance for CA (2DL CA) for 256QAM in DL
8.7.2.1_H.3 TDD Sustained data rate performance for CA (3DL CA) for 256QAM in DL
8.7.3 FDD (EPDCCH scheduling)
8.7.3.1 FDD sustained data rate performance for EPDCCH scheduling
8.7.3.1.1 Test purpose
8.7.3.1.2 Test applicability
8.7.3.1.3 Minimum requirements
8.7.3.1.4 Test description
8.7.3.1.5 Test requirement
8.7.4 TDD (EPDCCH scheduling)
8.7.4.1 TDD sustained data rate performance for EPDCCH scheduling
8.7.4.1.1 Test purpose
8.7.4.1.2 Test applicability
8.7.4.1.3 Minimum requirements
8.7.4.1.4 Test description
8.7.4.1.5 Test requirement
8.7.5 TDD FDD CA Sustained data rate performance
8.7.5.1 TDD FDD CA Sustained data rate performance for FDD PCell
8.7.5.1.1 TDD FDD CA Sustained data rate performance for FDD PCell (2DL CA)
8.7.5.1.1.1 Test purpose
8.7.5.1.1.2 Test applicability
8.7.5.1.1.3 Minimum requirements
8.7.5.1.1.4 Test description
8.7.5.1.1.5 Test requirement
8.7.5.1.2 TDD FDD CA Sustained data rate performance for FDD PCell (3DL CA)
8.7.5.1.2.1 Test purpose
8.7.5.1.2.2 Test applicability
8.7.5.1.2.3 Minimum requirements
8.7.5.1.2.4 Test description
8.7.5.1.2.5 Test requirement
8.7.5.1.3 TDD FDD CA Sustained data rate performance for FDD PCell (4DL CA)
8.7.5.1.3.1 Test purpose
8.7.5.1.3.2 Test applicability
8.7.5.1.3.3 Minimum requirements
8.7.5.1.3.4 Test description
8.7.5.1.3.5 Test requirement
8.7.5.1.4 TDD FDD CA Sustained data rate performance for FDD PCell (5DL CA)
8.7.5.1.4.1 Test purpose
8.7.5.1.4.2 Test applicability
8.7.5.1.4.3 Minimum requirements
8.7.5.1.4.4 Test description
8.7.5.1.4.5 Test requirement
8.7.5.1_H TDD FDD CA Sustained data rate performance for FDD PCell for 256QAM in DL
8.7.5.1_H.1 TDD FDD CA Sustained data rate performance for FDD PCell (2DL CA) for 256QAM in DL
8.7.5.1_H.1.1 Test purpose
8.7.5.1_H.1.2 Test applicability
8.7.5.1_H.1.3 Minimum requirements
8.7.5.1_H.1.4 Test description
8.7.5.1_H.1.5 Test requirement
8.7.5.1_H.2 TDD FDD CA Sustained data rate performance for FDD PCell (3DL CA) for 256QAM in DL
8.7.5.1_H.2.1 Test purpose
8.7.5.1_H.2.2 Test applicability
8.7.5.1_H.2.3 Minimum requirements
8.7.5.1_H.2.4 Test description
8.7.5.1_H.2.5 Test requirement
8.7.5.1_H.3 TDD FDD CA Sustained data rate performance for FDD PCell (4DL CA) for 256QAM in DL
8.7.5.1_H.3.1 Test purpose
8.7.5.1_H.3.2 Test applicability
8.7.5.1_H.3.3 Minimum requirements
8.7.5.1_H.3.4 Test description
8.7.5.1_H.3.5 Test requirement
8.7.5.1_H.4 TDD FDD CA Sustained data rate performance for FDD PCell (5DL CA) for 256QAM in DL
8.7.5.1_H.4.1 Test purpose
8.7.5.1_H.4.2 Test applicability
8.7.5.1_H.4.3 Minimum requirements
8.7.5.1_H.4.4 Test description
8.7.5.1_H.4.5 Test requirement
8.7.5.2 TDD FDD CA Sustained data rate performance for TDD PCell
8.7.5.2.1 TDD FDD CA Sustained data rate performance for TDD PCell (2DL CA)
8.7.5.2.1.1 Test purpose
8.7.5.2.1.2 Test applicability
8.7.5.2.1.3 Minimum requirements
8.7.5.2.1.4 Test description
8.7.5.2.1.5 Test requirement
8.7.5.2.2 TDD FDD CA Sustained data rate performance for TDD PCell (3DL CA)
8.7.5.2.2.1 Test purpose
8.7.5.2.2.2 Test applicability
8.7.5.2.2.3 Minimum requirements
8.7.5.2.2.4 Test description
8.7.5.2.2.5 Test requirement
8.7.5.2.3 TDD FDD CA Sustained data rate performance for TDD PCell (4DL CA)
8.7.5.2.3.1 Test purpose
8.7.5.2.3.2 Test applicability
8.7.5.2.3.3 Minimum requirements
8.7.5.2.3.4 Test description
8.7.5.2.3.5 Test requirement
8.7.5.2_H TDD FDD CA Sustained data rate performance for TDD PCell for 256QAM in DL
8.7.5.2_H.1 TDD FDD CA Sustained data rate performance for TDD PCell (2DL CA) for 256QAM in DL
8.7.5.2_H.1.1 Test purpose
8.7.5.2_H.1.2 Test applicability
8.7.5.2_H.1.3 Minimum requirements
8.7.5.2_H.1.4 Test description
8.7.5.2_H.1.5 Test requirement
8.7.5.2_H.2 TDD FDD CA Sustained data rate performance for TDD PCell (3DL CA) for 256QAM in DL
8.7.5.2_H.2.1 Test purpose
8.7.5.2_H.2.2 Test applicability
8.7.5.2_H.2.3 Minimum requirements
8.7.5.2_H.2.4 Test description
8.7.5.2_H.2.5 Test requirement
8.7.5.2_H.3 TDD FDD CA Sustained data rate performance for TDD PCell (4DL CA) for 256QAM in DL
8.7.5.2_H.3.1 Test purpose
8.7.5.2_H.3.2 Test applicability
8.7.5.2_H.3.3 Minimum requirements
8.7.5.2_H.3.4 Test description
8.7.5.2_H.3.5 Test requirement
8.7.5.2.4 TDD FDD CA Sustained data rate performance for TDD PCell (5DL CA)
8.7.5.2.4.1 Test purpose
8.7.5.2.4.2 Test applicability
8.7.5.2.4.3 Minimum requirements
8.7.5.2.4.4 Test description
8.7.5.2.4.5 Test requirement
8.7.6 FDD (Dual Connectivity)
8.7.6.1 FDD sustained data rate performance for Dual Connectivity 64QAM
8.7.6.1.1 Test purpose
8.7.6.1.2 Test applicability
8.7.6.1.3 Minimum conformance requirements
8.7.6.1.4 Test description
8.7.6.1.4.1 Initial conditions
8.7.6.1.4.2 Test procedure
8.7.6.1.4.3 Message contents
8.7.6.1.5 Test requirement
8.7.6.2 FDD sustained data rate performance for Dual Connectivity 256QAM
8.7.6.2.1 Test purpose
8.7.6.2.2 Test applicability
8.7.6.2.3 Minimum conformance requirements
8.7.6.2.4 Test description
8.7.6.2.5 Test requirement
8.7.7 TDD (Dual Connectivity)
8.7.7.1 TDD sustained data rate performance for Dual Connectivity 64QAM
8.7.7.1.1 Test purpose
8.7.7.1.2 Test applicability
8.7.7.1.3 Minimum conformance requirements
8.7.7.1.4 Test description
8.7.7.1.4.1 Initial conditions
8.7.7.1.4.2 Test procedure
8.7.7.1.4.3 Message contents
8.7.7.1.5 Test requirement
8.7.7.2 TDD sustained data rate performance for Dual Connectivity 256QAM
8.7.7.2.1 Test purpose
8.7.7.2.2 Test applicability
8.7.7.2.3 Minimum conformance requirements
8.7.7.2.4 Test description
8.7.7.2.5 Test requirement
8.7.8
8.7.9 FDD sustained data rate performance (4 layer MIMO)
8.7.9.1 Minimum conformance requirements
8.7.9.2 FDD sustained data rate performance for 4 layer MIMO (single carrier)
8.7.9.2.1 Test purpose
8.7.9.2.2 Test applicability
8.7.9.2.3 Minimum conformance requirements
8.7.9.2.4 Test description
8.7.9.2.5 Test requirement
8.7.9.3 FDD sustained data rate performance for 4 layer MIMO (2DL CA)
8.7.9.3.1 Test purpose
8.7.9.3.2 Test applicability
8.7.9.3.3 Minimum conformance requirements
8.7.9.3.4 Test description
8.7.9.3.5 Test requirement
8.7.9.4 FDD sustained data rate performance for 4 layer MIMO (3DL CA)
8.7.9.4.1 Test purpose
8.7.9.4.2 Test applicability
8.7.9.4.3 Minimum conformance requirements
8.7.9.4.4 Test description
8.7.9.4.5 Test requirement
8.7.9.5 FDD sustained data rate performance for 4 layer MIMO (4DL CA)
8.7.9.5.1 Test purpose
8.7.9.5.2 Test applicability
8.7.9.5.3 Minimum conformance requirements
8.7.9.5.4 Test description
8.7.9.5.5 Test requirement
8.7.9.6 FDD sustained data rate performance for 4 layer MIMO (5DL CA)
8.7.9.6.1 Test purpose
8.7.9.6.2 Test applicability
8.7.9.6.3 Minimum conformance requirements
8.7.9.6.4 Test description
8.7.9.6.5 Test requirement
8.7.10 TDD sustained data rate performance (4 layer MIMO)
8.7.10.1 Minimum conformance requirements
8.7.10.2 TDD sustained data rate performance for 4 layer MIMO (single carrier)
8.7.10.2.1 Test purpose
8.7.10.2.2 Test applicability
8.7.10.2.3 Minimum conformance requirements
8.7.10.2.4 Test description
8.7.10.2.5 Test requirement
8.7.10.3 TDD sustained data rate performance for 4 layer MIMO (2DL CA)
8.7.10.3.1 Test purpose
8.7.10.3.2 Test applicability
8.7.10.3.3 Minimum conformance requirements
8.7.10.3.4 Test description
8.7.10.3.5 Test requirement
8.7.10.4 TDD sustained data rate performance for 4 layer MIMO (3DL CA)
8.7.10.4.1 Test purpose
8.7.10.4.2 Test applicability
8.7.10.4.3 Minimum conformance requirements
8.7.10.4.4 Test description
8.7.10.4.5 Test requirement
8.7.10.5 TDD sustained data rate performance for 4 layer MIMO (4DL CA)
8.7.10.5.1 Test purpose
8.7.10.5.2 Test applicability
8.7.10.5.3 Minimum conformance requirements
8.7.10.5.4 Test description
8.7.10.5.5 Test requirement
8.7.10.6 TDD sustained data rate performance for 4 layer MIMO (5DL CA)
8.7.10.6.1 Test purpose
8.7.10.6.2 Test applicability
8.7.10.6.3 Minimum conformance requirements
8.7.10.6.4 Test description
8.7.10.6.5 Test requirement
8.7.11 TDD FDD CA Sustained data rate performance (4 layer MIMO)
8.7.11.1 Minimum conformance requirements
8.7.11.2 TDD FDD CA sustained data rate performance for 4 layer MIMO (2DL CA)
8.7.11.2.1 Test purpose
8.7.11.2.2 Test applicability
8.7.11.2.3 Minimum conformance requirements
8.7.11.2.4 Test description
8.7.11.2.5 Test requirement
8.7.11.3 TDD FDD CA sustained data rate performance for 4 layer MIMO (3DL CA)
8.7.11.3.1 Test purpose
8.7.11.3.2 Test applicability
8.7.11.3.3 Minimum conformance requirements
8.7.11.3.4 Test description
8.7.11.3.5 Test requirement
8.7.11.4 TDD FDD CA sustained data rate performance for 4 layer MIMO (4DL CA)
8.7.11.4.1 Test purpose
8.7.11.4.2 Test applicability
8.7.11.4.3 Minimum conformance requirements
8.7.11.4.4 Test description
8.7.11.4.5 Test requirement
8.7.11.5 TDD FDD CA sustained data rate performance for 4 layer MIMO (5DL CA)
8.7.11.5.1 Test purpose
8.7.11.5.2 Test applicability
8.7.11.5.3 Minimum conformance requirements
8.7.11.5.4 Test description
8.7.11.5.5 Test requirement
8.7.12 LAA Sustained data rate performance
8.7.12.1 FDD CA in unlicensed bands
8.7.12.1.1 Minimum conformance requirements (FDD CA in unlicensed bands)
8.7.12.1.2 LAA sustained data rate performance with FDD as Pcell with 2DL CA
8.7.12.1.2.1 LAA sustained data rate performance with FDD PCell with 2DL CA (2Rx)
8.7.12.1.2.1.1 Test purpose
8.7.12.1.2.1.2 Test applicability
8.7.12.1.2.1.3 Minimum requirements
8.7.12.1.2.1.4 Test description
8.7.12.1.2.1.5 Test requirement
8.7.12.1.2.2 LAA sustained data rate performance with FDD PCell for 4 layer MIMO (2DL CA)
8.7.12.1.2.2.1 Test purpose
8.7.12.1.2.2.2 Test applicability
8.7.12.1.2.2.3 Minimum requirements
8.7.12.1.2.2.4 Test description
8.7.12.1.2.2.5 Test requirement
8.7.12.2 TDD CA in unlicensed bands
8.7.12.2.1 Minimum conformance requirements (TDD CA in unlicensed bands)
8.7.12.2.2 LAA sustained data rate performance with TDD as Pcell with 2DL CA
8.7.12.2.2.1 LAA sustained data rate performance with TDD PCell with 2DL CA (2Rx)
8.7.12.2.2.1.1 Test purpose
8.7.12.2.2.1.2 Test applicability
8.7.12.2.2.1.3 Minimum requirements
8.7.12.2.2.1.4 Test description
8.7.12.2.2.1.4.1 Initial conditions
8.7.12.2.2.1.5 Test requirement
8.7.12.2.2.2 LAA sustained data rate performance with TDD PCell for 4 layer MIMO (2DL CA)
8.7.12.2.2.2.1 Test purpose
8.7.12.2.2.2.2 Test applicability
8.7.12.2.2.2.3 Minimum requirements
8.7.12.2.2.2.4 Test description
8.7.12.2.2.2.5 Test requirement
8.8 Demodulation of EPDCCH
8.8.1 Distributed Transmission
8.8.1.1 FDD distributed EPDCCH performance
8.8.1.1.1 Test purpose
8.8.1.1.2 Test applicability
8.8.1.1.3 Minimum conformance requirements
8.8.1.1.4 Test description
8.8.1.1.5 Test requirement
8.8.1.2 TDD distributed EPDCCH performance
8.8.1.2.1 Test purpose
8.8.1.2.2 Test applicability
8.8.1.2.3 Minimum conformance requirements
8.8.1.2.4 Test description
8.8.1.2.5 Test requirement
8.8.2 Localized Transmission with TM9
8.8.2.1 FDD localized EPDCCH performance with TM9
8.8.2.1.1 Test purpose
8.8.2.1.2 Test applicability
8.8.2.1.3 Minimum conformance requirements
8.8.2.1.4 Test description
8.8.2.1.5 Test requirement
8.8.2.2 TDD localized EPDCCH performance with TM9
8.8.2.2.1 Test purpose
8.8.2.2.2 Test applicability
8.8.2.2.3 Minimum conformance requirements
8.8.2.2.4 Test description
8.8.2.2.5 Test requirement
8.8.3 Localized transmission with TM10 Type B quasi co-location type
8.8.3.1 FDD localized EPDCCH transmission with TM10 Type B quasi co-location type
8.8.3.1.1 Test purpose
8.8.3.1.2 Test applicability
8.8.3.1.3 Minimum conformance requirements
8.8.3.1.4 Test description
8.8.3.1.5 Test requirement
8.8.3.2 TDD localized EPDCCH transmission with TM10 Type B quasi co-location type
8.8.3.2.1 Test purpose
8.8.3.2.2 Test applicability
8.8.3.2.3 Minimum conformance requirements
8.8.3.2.4 Test description
8.8.3.2.5 Test requirement
8.8.4
8.8.4.1 FDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH - Localized Transmission with CRS Inter
8.8.4.2 TDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH - Localized Transmission with CRS Inter
8.8.5
8.8.5.1 TDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH - Distributed Transmission with TM9 Int
8.8.6
8.8.6.1 FDD Enhanced Downlink Control Channel Performance Requirement Type A for EDPCCH- Distributed Transmission with TM3 Inte
8.9 Demodulation (Single receiver antenna)
8.9.1 PDSCH
8.9.1.1 FDD and half-duplex FDD (Fixed Reference Channel)
8.9.1.1.1 FDD PDSCH Transmit Diversity 2x1 for UE category 0
8.9.1.1.1_1 FDD PDSCH Transmit Diversity 2x1 for UE category 1bis
8.9.1.1.2 FDD closed-loop spatial multiplexing performance (Cell-Specific Reference Symbols)
8.9.1.1.2_1 FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 4x1 for UE Category 1bis
8.9.1.1.3 FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 0
8.9.1.1.3_1 FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 1bis
8.9.1.2 TDD (Fixed Reference Channel)
8.9.1.2.1 TDD PDSCH Transmit Diversity for UE category 0
8.9.1.2.2 TDD closed-loop spatial multiplexing performance (Cell-Specific Reference Symbols)
8.9.1.2.2_1 TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 4x1 for UE Category 1bis
8.9.1.2.3 TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 0)
8.9.1.2.3_1 TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category 1bis
8.9.2 PHICH
8.9.2.1 FDD and half-duplex FDD
8.9.2.1.1 FDD PHICH Transmit Diversity for UE category 0
8.9.2.1.1.1 Test purpose
8.9.2.1.1.2 Test applicability
8.9.2.1.1.3 Minimum conformance requirements
8.9.2.1.1.4 Test description
8.9.2.1.1.4.1 Initial conditions
8.9.2.1.1.4.2 Test procedure
8.9.2.1.1.4.3 Message contents
8.9.2.1.1.5 Test requirement
8.9.2.1.1_1 FDD PHICH Transmit Diversity for UE category 1bis
8.9.2.1.1_1.1 Test purpose
8.9.2.1.1_1.2 Test applicability
8.9.2.1.1_1.3 Minimum conformance requirements
8.9.2.1.1_1.4 Test description
8.9.2.1.1_1.4.1 Initial conditions
8.9.2.1.1_1.4.2 Test procedure
8.9.2.1.1_1.4.3 Message contents
8.9.2.1.1_1.5 Test requirement
8.9.2.2.1 TDD PHICH Transmit Diversity for UE category 0
8.9.2.2.1.1 Test purpose
8.9.2.2.1.2 Test applicability
8.9.2.2.1.3 Minimum conformance requirements
8.9.2.2.1.4 Test description
8.9.2.2.1.4.1 Initial conditions
8.9.2.2.1.4.2 Test procedure
8.9.2.2.1.4.3 Message contents
8.9.2.2.1.5 Test requirement
8.9.2.2.1_1 TDD PHICH Transmit Diversity for UE category 1bis
8.10 Demodulation (4 receiver antenna ports)
8.10.1 PDSCH
8.10.1.1 FDD (Fixed Reference Channel)
8.10.1.1.1 FDD PDSCH Transmit Diversity 2x4
8.10.1.1.2 FDD PDSCH Open Loop Spatial Multiplexing 2x4
8.10.1.1.3 FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model ΠEnhanced Performance Requi
8.10.1.1.4 FDD PDSCH Closed Loop Spatial Multiplexing 4x4
8.10.1.1.5 FDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 interference model ΠEnhanced Perfo
8.10.1.1.6 FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols)
8.10.1.1.7 FDD Open-loop spatial multiplexing, 3 Layer Multiplexing with 4 Tx Antenna Ports
8.10.1.1.8 FDD Closed-loop spatial multiplexing performance, 4 Layers spatial multiplexing 4 Tx antennas
8.10.1.1.9 FDD 4 Layer Spatial Multiplexing (User-Specific Reference Symbols)
8.10.1.1.9.1 Test purpose
8.10.1.1.9.2 Test applicability
8.10.1.1.9.3 Minimum conformance requirements
8.10.1.1.9.4 Test description
8.10.1.1.9.4.2 Test procedure
8.10.1.1.9.4.3 Message contents
8.10.1.1.9.5 Test requirement
8.10.1.2 TDD (Fixed Reference Channel)
8.10.1.2.1 TDD PDSCH Transmit Diversity 2x4
8.10.1.2.2 TDD PDSCH Open Loop Spatial Multiplexing 2x4
8.10.1.2.3 TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model ΠEnhanced Performance Requi
8.10.1.2.4 TDD PDSCH Closed Loop Spatial Multiplexing 4x4
8.10.1.2.5 TDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 interference model ΠEnhanced Perfo
8.10.1.2.6 TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols)
8.10.1.2.6.1 Test purpose
8.10.1.2.6.2 Test applicability
8.10.1.2.6.3 Minimum conformance requirements
8.10.1.2.6.4 Test description
8.10.1.2.6.4.2 Test procedure
8.10.1.2.6.4.3 Message contents
8.10.1.2.6.5 Test requirement
8.10.1.2.7 TDD Open-loop spatial multiplexing, 3 Layer Multiplexing with 4 Tx Antenna Ports
8.10.1.2.8 TDD Closed-loop spatial multiplexing performance, 4 Layers spatial multiplexing 4 Tx antennas
8.10.1.2.9 TDD 4 Layer Spatial Multiplexing (User-Specific Reference Symbols)
8.10.1.2.9.1 Test purpose
8.10.1.2.9.2 Test applicability
8.10.1.2.9.3 Minimum conformance requirements
8.10.1.2.9.4 Test description
8.10.1.2.9.4.2 Test procedure
8.10.1.2.9.4.3 Message contents
8.10.1.2.9.5 Test requirement
8.10.2 PCFICH/PDCCH
8.10.2.1 FDD
8.10.2.1.1 FDD PCFICH/PDCCH Single-antenna Port Performance 1x4
8.10.2.1.1.1 Test purpose
8.10.2.1.1.2 Test applicability
8.10.2.1.1.3 Minimum conformance requirements
8.10.2.1.1.4 Test description
8.10.2.1.1.4.1 Initial conditions
8.10.2.1.1.4.2 Test procedure
8.10.2.1.1.4.3 Message contents
8.10.2.1.1.5 Test requirement
8.10.2.1.2 FDD PCFICH/PDCCH Transmit Diversity 2x4
8.10.2.1.2.1 Test purpose
8.10.2.1.2.2 Test applicability
8.10.2.1.2.3 Minimum conformance requirements
8.10.2.1.2.4 Test description
8.10.2.1.2.4.1 Initial conditions
8.10.2.1.2.4.2 Test procedure
8.10.2.1.2.4.3 Message contents
8.10.2.1.2.5 Test requirement
8.10.2.1.3 FDD PCFICH/PDCCH Transmit Diversity 4x4
8.10.2.1.3.1 Test purpose
8.10.2.1.3.2 Test applicability
8.10.2.1.3.3 Minimum conformance requirements
8.10.2.1.3.4 Test description
8.10.2.1.3.4.1 Initial conditions
8.10.2.1.3.4.2 Test procedure
8.10.2.1.3.4.3 Message contents
8.10.2.1.3.5 Test requirement
8.10.2.2 TDD
8.10.2.2.1 TDD PCFICH/PDCCH Single-antenna Port Performance 1x4
8.10.2.2.1.1 Test purpose
8.10.2.2.1.2 Test applicability
8.10.2.2.1.3 Minimum conformance requirements
8.10.2.2.1.4 Test description
8.10.2.2.1.4.1 Initial conditions
8.10.2.2.1.4.2 Test procedure
8.10.2.2.1.4.3 Message contents
8.10.2.2.1.5 Test requirement
8.10.2.2.2 TDD PCFICH/PDCCH Transmit Diversity 2x4
8.10.2.2.2.1 Test purpose
8.10.2.2.2.2 Test applicability
8.10.2.2.2.3 Minimum conformance requirements
8.10.2.2.2.4 Test description
8.10.2.2.2.4.1 Initial conditions
8.10.2.2.2.4.2 Test procedure
8.10.2.2.2.4.3 Message contents
8.10.2.2.2.5 Test requirement
8.10.2.2.3 TDD PCFICH/PDCCH Transmit Diversity 4x4
8.10.2.2.3.1 Test purpose
8.10.2.2.3.2 Test applicability
8.10.2.2.3.3 Minimum conformance requirements
8.10.2.2.3.4 Test description
8.10.2.2.3.4.1 Initial conditions
8.10.2.2.3.4.2 Test procedure
8.10.2.2.3.4.3 Message contents
8.10.2.2.3.5 Test requirement
8.10.3 PHICH
8.10.3.1 FDD
8.10.3.1.1 FDD PHICH Single-antenna Port Performance 1x4
8.10.3.1.2 FDD PHICH Transmit Diversity 2x4
8.10.3.1.3 FDD PHICH Transmit Diversity 4x4
8.10.3.2 TDD
8.10.3.2.1 TDD PHICH Single-antenna Port Performance 1x4
8.10.3.2.2 TDD PHICH Transmit Diversity 2x4
8.10.3.2.3 TDD PHICH Transmit Diversity 4x4
8.10.4 ePDCCH
8.10.4.1 Distributed Transmission with 4Rx
8.10.4.1.1 FDD distributed EPDCCH performance 2x4
8.10.4.1.1.1 Test purpose
8.10.4.1.1.2 Test applicability
8.10.4.1.1.3 Minimum conformance requirements
8.10.4.1.1.4 Test description
8.10.4.1.1.5 Test requirement
8.10.4.1.2 TDD distributed EPDCCH performance 2x4
8.10.4.1.2.1 Test purpose
8.10.4.1.2.2 Test applicability
8.10.4.1.2.3 Minimum conformance requirements
8.10.4.1.2.4 Test description
8.10.4.1.2.5 Test requirement
8.10.4.2 Localized Transmission with TM9 2x4
8.10.4.2.1 FDD localized EPDCCH performance with TM9 2x4
8.10.4.2.1.1 Test purpose
8.10.4.2.1.2 Test applicability
8.10.4.2.1.3 Minimum conformance requirements
8.10.4.2.1.4 Test description
8.10.4.2.1.5 Test requirement
8.10.4.2.2 TDD localized EPDCCH performance with TM9 2x4
8.10.4.2.2.1 Test purpose
8.10.4.2.2.2 Test applicability
8.10.4.2.2.3 Minimum conformance requirements
8.10.4.2.2.4 Test description
8.10.4.2.2.5 Test requirement
8.11 Demodulation (UE supporting coverage enhancement)
8.11.1 PDSCH
8.11.1.1 FDD and half-duplex FDD (Fixed Reference Channel)
8.11.1.1.1 FDD and half-duplex FDD Closed-loop spatial multiplexing performance for UE supporting CE
8.11.1.1.2 FDD and half-duplex FDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE supporting CE
8.11.1.1.3 Transmit diversity performance (Cell-Specific Reference Symbols)
8.11.1.1.3.1 FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M1
8.11.1.1.3.1_1 FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M1 (CEmodeB)
8.11.1.1.3.2 FDD and half-duplex FDD PDSCH Transmit Diversity 2x1 for UE category M2
8.11.1.2 TDD (Fixed Reference Channel)
8.11.1.2.1 TDD Closed-loop spatial multiplexing performance for UE category M1 (Cell-Specific Reference Symbols)
8.11.1.2.2 TDD PDSCH Single-layer Spatial Multiplexing on antenna ports 7 or 8 for UE category M1
8.11.1.2.3 Transmit diversity performance (Cell-Specific Reference Symbols)
8.11.1.2.3.1 TDD PDSCH Transmit Diversity for UE category M1
8.11.1.2.3.1_1 TDD PDSCH Transmit Diversity for UE category M1 (CEModeB)
8.11.2 MPDCCH
8.11.2.1 FDD and HD-FDD
8.11.2.1.1 FDD and HD-FDD demodulation of MPDCCH in CE Mode A
8.11.2.1.1.1 Test purpose
8.11.2.1.1.2 Test applicability
8.11.2.1.1.3 Minimum conformance requirements
8.11.2.1.1.4 Test description
8.11.2.1.1.5 Test requirement
8.11.2.1.2 FDD and half-duplex FDD demodulation of MPDCCH in CE Mode B
8.11.2.1.2.1 Test purpose
8.11.2.1.2.2 Test applicability
8.11.2.1.2.3 Minimum conformance requirements
8.11.2.1.2.4 Test description
8.11.2.1.2.5 Test requirement
8.11.2.2 TDD
8.11.2.2.1 TDD demodulation of MPDCCH in CE Mode A
8.11.2.2.1.1 Test purpose
8.11.2.2.1.2 Test applicability
8.11.2.2.1.3 Minimum conformance requirements
8.11.2.2.1.4 Test description
8.11.2.2.1.5 Test requirement
8.11.2.2.2 TDD demodulation of MPDCCH in CE Mode B
8.11.2.2.2.1 Test purpose
8.11.2.2.2.2 Test applicability
8.11.2.2.2.3 Minimum conformance requirements
8.11.2.2.2.4 Test description
8.11.2.2.2.5 Test requirement
8.11.3 Demodulation of PBCH (enhanced coverage)
8.12 Demodulation of Narrowband IoT
8.12.1 NPDSCH
8.12.1.1 Half-duplex FDD
8.12.1.1.1 Demodulation of NPDSCH (Cell-Specific Reference Symbols) in In-band mode for category NB1 and NB2
8.12.1.1.2 Demodulation of NPDSCH (Cell-Specific Reference Symbols) in standalone and Guard-band mode for category NB1 and NB2
8.12.1.1.3 Demodulation of NPDSCH (Cell-Specific Reference Symbols) in standalone for NB2
8.12.2 NPDCCH
8.12.2.1 Half-duplex FDD
8.12.2.1.1 Demodulation of NPDCCH single-antenna performance for category NB1 and NB2
8.12.2.1.2 Demodulation of NPDCCH Transmit diversity performance for category NB1 and NB2
8.13 Demodulation of PDSCH CA and DC (4 receiver antenna ports)
8.13.1 FDD (CA and DC)
8.13.1.1 Closed Loop Multi Layer Spatial Multiplexing
8.13.1.1.1 Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA
8.13.1.1.1.1 Minimum Requirement
8.13.1.1.1.2 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (2DL CA)
8.13.1.1.1.3 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (3DL CA)
8.13.1.1.1.4 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (4DL CA)
8.13.1.1.1.5 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 (5DL CA)
8.13.1.1.2
8.13.1.1.3 FDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM (2DL CA)
8.13.1.1.4 FDD PDSCH Closed Loop Four-Layer Spatial Multiplexing for CA (2DL CA)
8.13.1.2 Dual-Layer Spatial Multiplexing (User-Specific Reference Symbols)
8.13.1.2.2 FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (2DL CA)
8.13.1.2.2.1 Test purpose
8.13.1.2.2.2 Test applicability
8.13.1.2.2.3 Minimum conformance requirements
8.13.1.2.2.4 Test description
8.13.1.2.2.5 Test requirement
8.13.1.2.3 FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (3DL CA)
8.13.1.2.3.1 Test purpose
8.13.1.2.3.2 Test applicability
8.13.1.2.3.3 Minimum conformance requirements
8.13.1.2.3.4 Test description
8.13.1.2.3.5 Test requirement
8.13.1.2.4 FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (4DL CA)
8.13.1.2.4.1 Test purpose
8.13.1.2.4.2 Test applicability
8.13.1.2.4.3 Minimum conformance requirements
8.13.1.2.4.4 Test description
8.13.1.2.4.5 Test requirement
8.13.1.2.5 FDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (5DL CA)
8.13.1.2.5.1 Test purpose
8.13.1.2.5.2 Test applicability
8.13.1.2.5.3 Minimum conformance requirements
8.13.1.2.5.4 Test description
8.13.1.2.5.5 Test requirement
8.13.1.3 Enhanced Performance Requirements Type A Closed-loop spatial multiplexing
8.13.1.3.1 FDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model ΠEnhanced Performance Requi
8.13.1.4 Enhanced Performance Requirement Type A - Single-layer Spatial Multiplexing (User-Specific Reference Symbols)
8.13.1.4.1 FDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Perfo
8.13.2 TDD (CA and DC)
8.13.2.1 Closed Loop Multi Layer Spatial Multiplexing
8.13.2.1.1 Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA
8.13.2.1.1.1 Minimum Requirement
8.13.2.1.1.2 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (2DL CA)
8.13.2.1.1.3 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (3DL CA)
8.13.2.1.1.4 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (4DL CA)
8.13.2.1.1.5 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for CA (5DL CA)
8.13.2.1.3 TDD PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM (2DL CA)
8.13.2.1.3.1 Test purpose
8.13.2.1.3.2 Test applicability
8.13.2.1.3.3 Minimum conformance requirements
8.13.2.1.3.4 Test description
8.13.2.1.3.5 Test requirement
8.13.2.1.4 TDD PDSCH Closed Loop Four-Layer Spatial Multiplexing for CA (2DL CA)
8.13.2.1.4.1 Test purpose
8.13.2.1.4.2 Test applicability
8.13.2.1.4.3 Minimum conformance requirements
8.13.2.1.4.4 Test description
8.13.2.1.4.5 Test requirement
8.13.2.2 Dual-Layer Spatial Multiplexing (User-Specific Reference Symbols)
8.13.2.2.1 Minimum Requirement
8.13.2.2.2 TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (2DL CA)
8.13.1.2.2.1 Test purpose
8.13.2.2.2.2 Test applicability
8.13.2.2.2.3 Minimum conformance requirements
8.13.2.2.2.4 Test description
8.13.2.2.2.5 Test requirement
8.13.2.2.3 TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (3DL CA)
8.13.2.2.3.1 Test purpose
8.13.2.2.3.2 Test applicability
8.13.2.2.3.3 Minimum conformance requirements
8.13.2.2.3.4 Test description
8.13.2.2.3.5 Test requirement
8.13.2.2.4 TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (4DL CA)
8.13.2.2.4.1 Test purpose
8.13.2.2.4.2 Test applicability
8.13.2.2.4.3 Minimum conformance requirements
8.13.2.2.4.4 Test description
8.13.2.2.4.5 Test requirement
8.13.2.2.5 TDD Dual-Layer Spatial Multiplexing 2x4 (User-Specific Reference Symbols) (5DL CA)
8.13.2.2.5.1 Test purpose
8.13.2.2.5.2 Test applicability
8.13.2.2.5.3 Minimum conformance requirements
8.13.2.2.5.4 Test description
8.13.2.2.5.5 Test requirement
8.13.2.3 Enhanced Performance Requirements Type A Closed-loop spatial multiplexing
8.13.2.3.1 TDD PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model ΠEnhanced Performance Requi
8.13.2.4 Enhanced Performance Requirement Type A - Single-layer Spatial Multiplexing (User-Specific Reference Symbols)
8.13.2.4.1 TDD PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model - Enhanced Perfo
8.13.3 TDD-FDD (CA and DC)
8.13.3.1 Closed Loop Multi Layer Spatial Multiplexing
8.13.3.1.1 Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell
8.13.3.1.1.1 Minimum Requirement
8.13.3.1.1.2 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (2DL CA)
8.13.3.1.1.3 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (3DL CA)
8.13.3.1.1.4 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (4DL CA)
8.13.3.1.1.5 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for FDD PCell (5DL CA)
8.13.3.1.2 Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell
8.13.3.1.2.1 Minimum Requirement
8.13.3.1.2.2 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (2DL CA)
8.13.3.1.2.3 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (3DL CA)
8.13.3.1.2.4 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (4DL CA)
8.13.3.1.2.5 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 for TDD PCell (5DL CA)
8.13.3.2 Dual-Layer Spatial Multiplexing (User-Specific Reference Symbols)
8.13.3.2.1 Minimum Requirement Dual-Layer Spatial Multiplexing 2 Tx Antenna Port for FDD PCell
8.13.3.2.2 Minimum Requirement Dual-Layer Spatial Multiplexing 2 Tx Antenna Port for TDD PCell
8.13.3.2.3 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (2DL CA)
8.13.3.2.3.1 Test purpose
8.13.3.2.3.2 Test applicability
8.13.3.2.3.3 Minimum conformance requirements
8.13.3.2.3.4 Test description
8.13.3.2.3.5 Test requirement
8.13.3.2.4 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (3DL CA)
8.13.3.2.4.1 Test purpose
8.13.3.2.4.2 Test applicability
8.13.3.2.4.3 Minimum conformance requirements
8.13.3.2.4.4 Test description
8.13.3.2.4.5 Test requirement
8.13.3.2.5 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (4DL CA)
8.13.3.2.5.1 Test purpose
8.13.3.2.5.2 Test applicability
8.13.3.2.5.3 Minimum conformance requirements
8.13.3.2.5.4 Test description
8.13.3.2.5.5 Test requirement
8.13.3.2.6 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for FDD PCell (User-Specific Reference Symbols) (5DL CA)
8.13.3.2.6.1 Test purpose
8.13.3.2.6.2 Test applicability
8.13.3.2.6.3 Minimum conformance requirements
8.13.3.2.6.4 Test description
8.13.3.2.6.5 Test requirement
8.13.3.2.7 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (2DL CA)
8.13.3.2.7.1 Test purpose
8.13.3.2.7.2 Test applicability
8.13.3.2.7.3 Minimum conformance requirements
8.13.3.2.7.4 Test description
8.13.3.2.7.5 Test requirement
8.13.3.2.8 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (3DL CA)
8.13.3.2.8.1 Test purpose
8.13.3.2.8.2 Test applicability
8.13.3.2.8.3 Minimum conformance requirements
8.13.3.2.8.4 Test description
8.13.3.2.8.5 Test requirement
8.13.3.2.9 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (4DL CA)
8.13.3.2.9.1 Test purpose
8.13.3.2.9.2 Test applicability
8.13.3.2.9.3 Minimum conformance requirements
8.13.3.2.9.4 Test description
8.13.3.2.9.5 Test requirement
8.13.3.2.10 TDD-FDD CA Dual-Layer Spatial Multiplexing 2x4 for TDD PCell (User-Specific Reference Symbols) (5DL CA)
8.13.3.2.10.1 Test purpose
8.13.3.2.10.2 Test applicability
8.13.3.2.10.3 Minimum conformance requirements
8.13.3.2.10.4 Test description
8.13.3.2.10.5 Test requirement
8.13.3.3 Enhanced Performance Requirements Type A Closed-loop spatial multiplexing
8.13.3.3.1 TDD-FDD CA PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model-Enhanced Performance
8.13.3.3.2 TDD-FDD CA PDSCH Closed Loop Single Layer Spatial Multiplexing 2x4 with TM4 Interference Model-Enhanced Performance
8.13.3.4 Enhanced Performance Requirements Type A ΠSingle-layer Spatial Multiplexing (User-Specific Reference Symbols)
8.13.3.4.1 TDD-FDD CA PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model-Enhanced
8.13.3.4.2 TDD-FDD CA PDSCH Single-layer Spatial Multiplexing 2x4 on antenna ports 7 or 8 with TM9 Interference Model-Enhanced
8.13.3.5
8.13.3.6 Closed-loop spatial multiplexing performance 4Tx Antenna Port with 256QAM
8.13.3.6.1 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM for FDD PCell (2DL CA)
8.13.3.6.2 TDD-FDD CA PDSCH Closed Loop Multi Layer Spatial Multiplexing 4x4 with 256QAM for TDD PCell (2DL CA)
8.13.3.7 Closed-loop spatial multiplexing performance 4Tx Antenna Port with Four layers
8.13.3.7.1 TDD-FDD CA PDSCH Closed Loop Four-Layer Spatial Multiplexing for FDD PCell (2DL CA)
8.13.3.7.1.1 Test purpose
8.13.3.7.1.2 Test applicability
8.13.3.7.1.3 Minimum conformance requirements
8.13.3.7.1.4 Test description
8.13.3.7.1.5 Test requirement
8.13.3.7.2 TDD-FDD CA PDSCH Closed Loop Four-Layer Spatial Multiplexing for TDD PCell (2DL CA)
8.13.3.7.2.1 Test purpose
8.13.3.7.2.2 Test applicability
8.13.3.7.2.3 Minimum conformance requirements
8.13.3.7.2.4 Test description
8.13.3.7.2.5 Test requirement
9 Reporting of Channel State Information
9.1 General
9.1.1 Applicability of requirements
9.1.1.1 Applicability of requirements for different channel bandwidths
9.1.1.2 Applicability and test rules for different CA configurations and bandwidth combination sets
9.1.1.2A Applicability and test rules for different TDD-FDD CA configurations and bandwidth combination sets
9.1.1.3 Test coverage for different number of component carriers
9.1.1.4 Applicability of performance requirements for 4Rx capable UEs
9.1.1.4.1 Applicability rule and antenna connection for single carrier tests with 2Rx
9.1.1.4.2 Applicability rule and antenna connection for CA tests with 2Rx
9.1.1.4.3 Applicability rule and antenna connection for single carrier tests with 4Rx
9.1.1.5 Applicability of requirements for UEs supporting coverage enhancement
9.2 CQI Reporting under AWGN conditions
9.2.1 CQI Reporting under AWGN conditions - PUCCH 1-0 (Cell-Specific Reference Symbols)
9.2.1.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0
9.2.1.1.1 Test purpose
9.2.1.1.2 Test applicability
9.2.1.1.3 Minimum conformance requirements
9.2.1.1.4 Test description
9.2.1.1.5 Test requirement
9.2.1.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0
9.2.1.2.1 Test purpose
9.2.1.2.2 Test applicability
9.2.1.2.3 Minimum conformance requirements
9.2.1.2.4 Test description
9.2.1.2.5 Test requirement
9.2.1.3
9.2.1.3_C FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for eICIC
9.2.1.3_C.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for eICIC (non-MBSFN ABS)
9.2.1.4
9.2.1.4_C TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for eICIC
9.2.1.4_C.1 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for eICIC (non-MBSFN ABS)
9.2.1.5
9.2.1.5_E FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for feICIC
9.2.1.5_E.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for feICIC (non-MBSFN ABS)
9.2.1.5_E.1.1 Test purpose
9.2.1.5_E.1.2 Test applicability
9.2.1.5_E.1.3 Minimum conformance requirements
9.2.1.5_E.1.4 Test description
9.2.1.5_E.1.5 Test requirement
9.2.1.6
9.2.1.6_E TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for feICIC
9.2.1.6_E.1 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for feICIC (non-MBSFN ABS)
9.2.1.6_E.1.1 Test purpose
9.2.1.6_E.1.2 Test applicability
9.2.1.6_E.1.3 Minimum conformance requirements
9.2.1.6_E.1.4 Test description
9.2.1.6_E.1.5 Test requirement
9.2.1.7 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for 256QAM in DL
9.2.1.7.1 Test purpose
9.2.1.7.2 Test applicability
9.2.1.7.3 Minimum conformance requirements
9.2.1.7.4 Test description
9.2.1.7.5 Test requirement
9.2.1.8 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for 256QAM in DL
9.2.1.8.1 Test purpose
9.2.1.8.2 Test applicability
9.2.1.8.3 Minimum conformance requirements
9.2.1.8.4 Test description
9.2.1.8.5 Test requirement
9.2.2 CQI Reporting under AWGN conditions - PUCCH 1-1 (Cell-Specific Reference Symbols)
9.2.2.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-1
9.2.2.1.1 Test purpose
9.2.2.1.2 Test applicability
9.2.2.1.3 Minimum conformance requirements
9.2.2.1.4 Test description
9.2.2.1.5 Test requirement
9.2.2.1_D.5 Test requirement
9.2.2.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-1
9.2.2.2.1 Test purpose
9.2.2.2.2 Test applicability
9.2.2.2.3 Minimum conformance requirements
9.2.2.2.4 Test description
9.2.2.2.5 Test requirement
9.2.3 CQI Reporting under AWGN conditions - PUCCH 1-1 (CSI Reference Symbols)
9.2.3.1_D FDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 for eDL-MIMO
9.2.3.1_D.1 Test purpose
9.2.3.1_D.2 Test applicability
9.2.3.1_D.3 Minimum conformance requirements
9.2.3.1_D.4 Test description
9.2.3.1_D.5 Test requirement
9.2.3.2_D TDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 for eDL-MIMO
9.2.3.2_D.1 Test purpose
9.2.3.2_D.2 Test applicability
9.2.3.2_D.3 Minimum conformance requirements
9.2.3.2_D.4 Test description
9.2.3.2_D.5 Test requirement
9.2.4 CQI Reporting under AWGN conditions - Single CSI Process
9.2.4.1_F FDD CQI Reporting under AWGN conditions - Single CSI Process for CoMP
9.2.4.1_F.1 Test purpose
9.2.4.1_F.2 Test applicability
9.2.4.1_F.3 Minimum conformance requirements
9.2.4.1_F.4 Test description
9.2.4.1_F.5 Test requirement
9.2.4.2_F TDD CQI Reporting under AWGN conditions - Single CSI Process for CoMP
9.2.4.2_F.1 Test purpose
9.2.4.2_F.2 Test applicability
9.2.4.2_F.3 Minimum conformance requirements
9.2.4.2_F.4 Test description
9.2.4.2_F.5 Test requirement
9.2.5 TDD CQI Reporting under AWGN conditions Œ PUCCH 1-1 (when csi-SubframeSet Œr12 and EIMTA-MainConfigServCell-r12 are confi
9.2.5.1 Test purpose
9.2.5.2 Test applicability
9.2.5.3 Minimum conformance requirements
9.2.5.4 Test description
9.2.5.5 Test requirement
9.2.6 CQI Reporting under AWGN Conditions-PUSCH 3-0 ΠLAA (Cell-Specific Reference Symbols)
9.2.6.1 LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with FDD as Pcell (PUSCH 3-0)
9.2.6.1.1 Test purpose
9.2.6.1.2 Test applicability
9.2.6.1.3 Minimum conformance requirements
9.2.6.1.4 Test description
9.2.6.1.5 Test requirement
9.2.6.2 LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with TDD as Pcell (PUSCH 3-0)
9.2.6.2.1 Test purpose
9.2.6.2.2 Test applicability
9.2.6.2.3 Minimum conformance requirements
9.2.6.2.4 Test description
9.2.6.2.5 Test requirement
9.2.7 CQI Reporting under AWGN Conditions-PUSCH 3-1 - LAA
9.2.7.1 LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with FDD as Pcell (PUSCH 3-1)
9.2.7.1.1 Test purpose
9.2.7.1.2 Test applicability
9.2.7.1.3 Minimum conformance requirements
9.2.7.1.4 Test description
9.2.7.1.5 Test requirement
9.2.7.2 LAA CQI Reporting under AWGN Conditions with Frame Structure Type 3 with TDD as Pcell (PUSCH 3-1)
9.2.7.2.1 Test purpose
9.2.7.2.2 Test applicability
9.2.7.2.3 Minimum conformance requirements
9.2.7.2.4 Test description
9.2.7.2.5 Test requirement
9.3 CQI Reporting under fading conditions
9.3.1 Frequency-selective scheduling mode
9.3.1.1 CQI Reporting under fading conditions ΠPUSCH 3-0 (Cell-Specific Reference Symbols)
9.3.1.1.1 FDD CQI Reporting under fading conditions ΠPUSCH 3-0
9.3.1.1.2 TDD CQI Reporting under fading conditions ΠPUSCH 3-0
9.3.1.1.3 to 9.3.1.1.4
9.3.1.1.5 TDD CQI Reporting under fading conditions Œ PUCCH 3-0 (when csi-SubframeSet Œr12 is configured)
9.3.1.1.5.1 Test purpose
9.3.1.1.5.2 Test applicability
9.3.1.1.5.3 Minimum conformance requirements
9.3.1.1.5.4 Test description
9.3.1.1.5.5 Test requirement
9.3.1.2 CQI Reporting under fading conditions ΠPUSCH 3-1 (CSI Reference Symbols)
9.3.1.2.1_D FDD CQI Reporting under fading conditions ΠPUSCH 3-1 for eDL MIMO
9.3.1.2.2_D TDD CQI Reporting under fading conditions ΠPUSCH 3-1 for eDL MIMO
9.3.1.2.3 FDD CQI Reporting under fading conditions ΠPUSCH 3-1 for 256QAM in DL
9.3.1.2.4 TDD CQI Reporting under fading conditions ΠPUSCH 3-1 for 256QAM in DL
9.3.1.2.5
9.3.1.2.6 TDD CQI Reporting under fading conditions Œ PUCCH 3-1 (when csi-SubframeSet Œr12 is configured with one CSI process)
9.3.1.2.6.1 Test purpose
9.3.1.2.6.2 Test applicability
9.3.1.2.6.3 Minimum conformance requirements
9.3.1.2.6.4 Test description
9.3.1.2.6.5 Test requirement
9.3.1.3 CQI Reporting under fading conditions ΠPUSCH 3-0 (Cell-Specific Reference Symbols)
9.3.1.3.1
9.3.1.3.1_E FDD CQI Reporting under fading conditions ΠPUSCH 3-0 for feICIC
9.3.1.3.1_E.1 FDD CQI Reporting under fading conditions ΠPUSCH 3-0 for feICIC (non-MBSFN ABS)
9.3.1.3.2
9.3.1.3.2_E TDD CQI Reporting under fading conditions ΠPUSCH 3-0 for feICIC
9.3.1.3.2_E.1 TDD CQI Reporting under fading conditions ΠPUSCH 3-0 for feICIC (non-MBSFN ABS)
9.3.2 Frequency non-selective scheduling mode
9.3.2.1 CQI Reporting under fading conditions ΠPUCCH 1-0 (Cell-Specific Reference Symbols)
9.3.2.1.1 FDD CQI Reporting under fading conditions ΠPUCCH 1-0
9.3.2.1.1_1 FDD CQI Reporting under fading conditions - PUCCH 1-0 (Release 9 and forward)
9.3.2.1.2 TDD CQI Reporting under fading conditions ΠPUCCH 1-0
9.3.2.2 CQI Reporting under fading conditions ΠPUCCH 1-1 (CSI Reference Symbols)
9.3.2.2.1_D FDD CQI Reporting under fading conditions ΠPUCCH 1-1 for eDL-MIMO
9.3.2.2.1_D.1 Test purpose
9.3.2.2.1_D.2 Test applicability
9.3.2.2.1_D.3 Minimum conformance requirements
9.3.2.2.1_D.4 Test description
9.3.2.2.1_D.4.2 Test procedure
9.3.2.2.1_D.4.3 Message contents
9.3.2.2.1_D.5 Test requirement
9.2.3.2A TDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 for FD-MIMO (With channelMeasRestriction configured)
9.2.3.2A.1 Test purpose
9.2.3.2A.2 Test applicability
9.2.3.2A.3 Minimum conformance requirements
9.2.3.2A.4 Test description
9.2.3.2A.5 Test requirement
9.3.2.2.2_D TDD CQI Reporting under fading conditions ΠPUCCH 1-1 for eDL-MIMO
9.3.2.2.2_D.1 Test purpose
9.3.2.2.2_D.2 Test applicability
9.3.2.2.2_D.3 Minimum conformance requirements
9.3.2.2.2_D.4 Test description
9.3.2.2.2_D.4.2 Test procedure
9.3.2.2.2_D.4.3 Message contents
9.3.3 Frequency-selective interference
9.3.3.1 CQI Reporting under fading conditions and frequency-selective interference ΠPUSCH 3-0 (Cell-Specific Reference Symbols
9.3.3.1.1 FDD CQI Reporting under fading conditions and frequency-selective interference ΠPUSCH 3-0
9.3.3.1.2 TDD CQI Reporting under fading conditions and frequency-selective interference ΠPUSCH 3-0
9.3.4 UE-selected subband CQI
9.3.4.1 CQI Reporting under fading conditions ΠPUSCH 2-0 (Cell-Specific Reference Symbols)
9.3.4.1.1 FDD CQI Reporting under fading conditions ΠPUSCH 2-0
9.3.4.1.2 TDD CQI Reporting under fading conditions ΠPUSCH 2-0
9.3.4.2 CQI Reporting under fading conditions ΠPUCCH 2-0 (Cell-Specific Reference Symbols)
9.3.4.2.1 FDD CQI Reporting under fading conditions ΠPUCCH 2-0
9.3.4.2.2 TDD CQI Reporting under fading conditions ΠPUCCH 2-0
9.3.5 Additional requirements for enhanced receiver Type A
9.3.5.1 PUCCH 1-0 (Cell-Specific Reference Symbol)
9.3.5.1.1 FDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A
9.3.5.1.2 TDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A
9.3.5.2 PUCCH 1-1 (CSI Reference Symbol)
9.3.5.2.1 FDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A
9.3.5.2.2 TDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A
9.3.6 CQI Reporting under fading conditions (With multiple CSI processes)
9.3.6.1_F FDD CQI Reporting under fading conditions with CSI processes for CoMP
9.3.6.1_F.1 FDD CQI Reporting under fading conditions with Single CSI process for CoMP
9.3.6.1_F.1.1 Test purpose
9.3.6.1_F.1.2 Test applicability
9.3.6.1_F.1.3 Minimum conformance requirements
9.3.6.1_F.1.4 Test description
9.3.6.1_F.1.4.1 Initial conditions
9.3.6.1_F.1.4.2 Test procedure
9.3.6.1_F.1.4.3 Message contents
9.3.6.1_F.1.5 Test requirement
9.3.6.1_F.2 FDD CQI Reporting under fading conditions with Three CSI processes for CoMP
9.3.6.1_F.2.1 Test purpose
9.3.6.1_F.2.2 Test applicability
9.3.6.1_F.2.3 Minimum conformance requirements
9.3.6.1_F.2.4 Test description
9.3.6.1_F.2.4.1 Initial conditions
9.3.6.1_F.2.4.2 Test procedure
9.3.6.1_F.2.4.3 Message contents
9.3.6.1_F.2.5 Test requirement
9.3.6.1_F.3 FDD CQI Reporting under fading conditions with Four CSI processes for CoMP
9.3.6.1_F.3.1 Test purpose
9.3.6.1_F.3.2 Test applicability
9.3.6.1_F.3.3 Minimum conformance requirements
9.3.6.1_F.3.4 Test description
9.3.6.1_F.3.4.1 Initial conditions
9.3.6.1_F.3.4.2 Test procedure
9.3.6.1_F.3.4.3 Message contents
9.3.6.1_F.3.5 Test requirement
9.3.6.2_F TDD CQI Reporting under fading conditions with CSI processes for CoMP
9.3.6.2_F.1 TDD CQI Reporting under fading conditions with Single CSI process for CoMP
9.3.6.2_F.1.1 Test purpose
9.3.6.2_F.1.2 Test applicability
9.3.6.2_F.1.3 Minimum conformance requirements
9.3.6.2_F.1.4 Test description
9.3.6.2_F.1.4.1 Initial conditions
9.3.6.2_F.1.4.2 Test procedure
9.3.6.2_F.1.4.3 Message contents
9.3.6.2_F.1.5 Test requirement
9.3.6.2_F.2 TDD CQI Reporting under fading conditions with Three CSI processes for CoMP
9.3.6.2_F.2.1 Test purpose
9.3.6.2_F.2.2 Test applicability
9.3.6.2_F.2.3 Minimum conformance requirements
9.3.6.2_F.2.4 Test description
9.3.6.2_F.2.4.1 Initial conditions
9.3.6.2_F.2.4.2 Test procedure
9.3.6.2_F.2.4.3 Message contents
9.3.6.2_F.2.5 Test requirement
9.3.6.2_F.3 TDD CQI Reporting under fading conditions with Four CSI processes for CoMP
9.3.6.2_F.3.1 Test purpose
9.3.6.2_F.3.2 Test applicability
9.3.6.2_F.3.3 Minimum conformance requirements
9.3.6.2_F.3.4 Test description
9.3.6.2_F.3.4.1 Initial conditions
9.3.6.2_F.3.4.2 Test procedure
9.3.6.2_F.3.4.3 Message contents
9.3.6.2_F.3.5 Test requirement
9.3.7 PUSCH 3-2 for eDL MIMO Enhancement
9.3.7.1 FDD CQI Reporting under fading conditions - PUSCH 3-2 for eDL MIMO Enhancement
9.3.7.1.1 Test purpose
9.3.7.1.2 Test applicability
9.3.7.1.3 Minimum conformance requirements
9.3.7.1.4 Test description
9.3.7.1.5 Test requirement
9.3.7.2 TDD CQI Reporting under fading conditions - PUSCH 3-2 for eDL MIMO Enhancement
9.3.7.2.1 Test purpose
9.3.7.2.2 Test applicability
9.3.7.2.3 Minimum conformance requirements
9.3.7.2.4 Test description
9.3.7.2.5 Test requirement
9.3.8 Additional requirements for enhanced receiver Type B
9.3.8.1 PUCCH 1-1 (Cell-Specific Reference Symbols)
9.3.8.1.1 FDD CQI Reporting under fading conditions - PUCCH 1-1 (Cell-Specific Reference Symbols) TM4 - Enhanced Receiver Type
9.3.8.1.2 TDD CQI Reporting under fading conditions - PUCCH 1-1 (Cell-Specific Reference Symbols) TM4 - Enhanced Receiver Type
9.3.8.2 PUCCH 1-1 (CSI Reference Symbols)
9.3.8.2.1 FDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM9 - Enhanced Receiver Type B
9.3.8.2.2 TDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM9 - Enhanced Receiver Type B
9.3.8.3 CSI process
9.3.8.3.1 FDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM10 with TM9 interference - Enhanced Re
9.3.8.3.2 TDD CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) TM10 with TM9 interference - Enhanced Re
9.4 Reporting of Precoding Matrix Indicator (PMI)
9.4.1 Single PMI
9.4.1.1 PMI Reporting ΠPUSCH 3-1 (Single PMI) (Cell-Specific Reference Symbols)
9.4.1.1.1 FDD PMI Reporting ΠPUSCH 3-1 (Single PMI)
9.4.1.1.2 TDD PMI Reporting ΠPUSCH 3-1 (Single PMI)
9.4.1.2 PMI Reporting ΠPUCCH 2-1 (Single PMI) (Cell-Specific Reference Symbols)
9.4.1.2.1 FDD PMI Reporting ΠPUCCH 2-1 (Single PMI)
9.4.1.2.2 TDD PMI Reporting ΠPUCCH 2-1 (Single PMI)
9.4.1.3 PMI Reporting ΠPUSCH 3-1 (Single PMI) (CSI Reference Symbols)
9.4.1.3.1
9.4.1.3.1_D FDD Reporting of PMI ΠPUSCH 3-1 (Single PMI) for eDL MIMO
9.4.1.3.2_D TDD Reporting of PMI ΠPUSCH 3-1 (Single PMI) for eDL-MIMO
9.4.1.3.3 FDD PMI Reporting with 12Tx Class A codebook ΠPUSCH 3-1 (Single PMI) for FD-MIMO
9.4.1.4 PMI Reporting ΠPUCCH 1-1 (Single PMI) (CSI Reference Symbol)
9.4.1.4.1 FDD PMI Reporting with 4Tx enhanced codebook ΠPUCCH 1-1 (Single PMI) for eDL MIMO Enhancement
9.4.1.4.2 TDD PMI Reporting with 4Tx enhanced codebook ΠPUCCH 1-1 (Single PMI) for eDL MIMO Enhancement
9.4.2 Multiple PMI
9.4.2.1 PMI Reporting ΠPUSCH 1-2 (Multiple PMI) (Cell-Specific Reference Symbols)
9.4.2.1.1 FDD PMI Reporting ΠPUSCH 1-2 (Multiple PMI)
9.4.2.1.1_1 FDD PMI Reporting ΠPUSCH 1-2 (Multiple PMI) (Release 9 and forward)
9.4.2.1.2 TDD PMI Reporting ΠPUSCH 1-2 (Multiple PMI)
9.4.2.1.2_1 TDD PMI Reporting ΠPUSCH 1-2 (Multiple PMI) (Release 9 and forward)
9.4.2.2 PMI Reporting ΠPUSCH 2-2 (Multiple PMI) (Cell-Specific Reference Symbols)
9.4.2.2.1 FDD PMI Reporting ΠPUSCH 2-2 (Multiple PMI)
9.4.2.2.2 TDD PMI Reporting ΠPUSCH 2-2 (Multiple PMI)
9.4.2.3 PMI Reporting ΠPUSCH 1-2 (Multiple PMI) (CSI Reference Symbols)
9.4.2.3.1
9.4.2.3.1_D FDD PMI Reporting - PUSCH 1-2 (Multiple PMI) for eDL-MIMO
9.4.2.3.2_D TDD PMI Reporting - PUSCH 1-2 (Multiple PMI) for eDL-MIMO
9.4.2.3.3 FDD PMI Reporting with 4Tx enhanced codebook - PUSCH 1-2 (Multiple PMI) for eDL-MIMO Enhancement
9.4.2.3.4 TDD PMI Reporting with 4Tx enhanced codebook - PUSCH 1-2 (Multiple PMI) for eDL-MIMO Enhancement
9.4.2.3.4.1 Test purpose
9.4.2.3.4.2 Test applicability
9.4.2.3.4.3 Minimum conformance requirements
9.4.2.3.4.4.2 Test procedure
9.5 Reporting of Rank Indicator (RI)
9.5.1 RI Reporting (Cell-Specific Reference Symbols)
9.5.1.1 FDD RI ReportingΠPUCCH 1-1
9.5.1.1.1 Test purpose
9.5.1.1.2 Test applicability
9.5.1.1.3 Minimum conformance requirements
9.5.1.1.4 Test description
9.5.1.1.5 Test requirement
9.5.1.1_1 FDD RI ReportingΠPUCCH 1-1 (Release 10)
9.5.1.1_1.1 Test purpose
9.5.1.1_1.2 Test applicability
9.5.1.1_1.3 Minimum conformance requirements
9.5.1.1_1.4 Test description
9.5.1.1_1.5 Test requirement
9.5.1.1_2 FDD RI ReportingΠPUCCH 1-1 (Release 11)
9.5.1.1_2.1 Test purpose
9.5.1.1_2.2 Test applicability
9.5.1.1_2.3 Minimum conformance requirements
9.5.1.1_2.4 Test description
9.5.1.1_2.5 Test requirement
9.5.1.2 TDD RI Reporting ΠPUSCH 3-1
9.5.1.2.1 Test purpose
9.5.1.2.2 Test applicability
9.5.1.2.3 Minimum conformance requirements
9.5.1.2.4 Test description
9.5.1.2.5 Test requirement
9.5.1.2_1 TDD RI Reporting ΠPUSCH 3-1 (Release 10)
9.5.1.2_1.1 Test purpose
9.5.1.2_1.2 Test applicability
9.5.1.2_1.3 Minimum conformance requirements
9.5.1.2_1.4 Test description
9.5.1.2_1.5 Test requirement
9.5.1.2_2 TDD RI Reporting ΠPUSCH 3-1 (Release 11)
9.5.1.2_2.1 Test purpose
9.5.1.2_2.2 Test applicability
9.5.1.2_2.3 Minimum conformance requirements
9.5.1.2_2.4 Test description
9.5.1.2_2.5 Test requirement
9.5.2 RI Reporting (CSI Reference Symbols)
9.5.2.1
9.5.2.1_D FDD RI Reporting- PUCCH 1-1 for eDL-MIMO
9.5.2.1_D.1 Test purpose
9.5.2.1_D.2 Test applicability
9.5.2.1_D.3 Minimum conformance requirements
9.5.2.1_D.4 Test description
9.5.2.1_D.5 Test requirement
9.5.2.2_D TDD RI Reporting- PUCCH 1-1 for eDL-MIMO
9.5.2.2_D.1 Test purpose
9.5.2.2_D.2 Test applicability
9.5.2.2_D.3 Minimum conformance requirements
9.5.2.2_D.4 Test description
9.5.2.2_D.5 Test requirement
9.5.3 RI Reporting (two CSI subframe sets are configured)
9.5.3.1_C FDD RI Reporting ΠPUCCH 1-0 for eICIC
9.5.3.1_C.1 FDD RI Reporting ΠPUCCH 1-0 for eICIC (non-MBSFN ABS)
9.5.3.1_C.1.1 Test purpose
9.5.3.1_C.1.2 Test applicability
9.5.3.1_C.1.3 Minimum conformance requirements
9.5.3.1_C.1.4 Test description
9.5.3.1_C.1.4.1 Initial conditions
9.5.3.1_C.1.4.2 Test procedure
9.5.3.1_C.1.4.3 Message contents
9.5.3.1_C.1.5 Test requirement
9.5.3.2_C TDD RI Reporting ΠPUCCH 1-0 for eICIC
9.5.3.2_C.1 TDD RI Reporting ΠPUCCH 1-0 for eICIC (non-MBSFN ABS)
9.5.3.2_C.1.1 Test purpose
9.5.3.2_C.1.2 Test applicability
9.5.3.2_C.1.3 Minimum conformance requirements
9.5.3.2_C.1.4 Test description
9.5.3.2_C.1.4.1 Initial conditions
9.5.3.2_C.1.4.2 Test procedure
9.5.3.2_C.1.4.3 Message contents
9.5.3.2_C.1.5 Test requirement
9.5.4 RI Reporting (two CSI subframe sets and CRS assistance information are configured)
9.5.4.1_E FDD RI Reporting ΠPUCCH 1-0 for feICIC
9.5.4.1_E.1 FDD RI Reporting ΠPUCCH 1-0 for feICIC (non-MBSFN ABS)
9.5.4.1_E.1.1 Test purpose
9.5.4.1_E.1.2 Test applicability
9.5.4.1_E.1.3 Minimum conformance requirements
9.5.4.1_E1.4 Test description
9.5.4.1_E.1.4.1 Initial conditions
9.5.4.1_E.1.4.2 Test procedure
9.5.4.1_E.1.4.3 Message contents
9.5.4.1_E.1.5 Test requirement
9.5.4.2_E TDD RI Reporting ΠPUCCH 1-0 for feICIC
9.5.4.2_E.1 TDD RI Reporting ΠPUCCH 1-0 for feICIC (non-MBSFN ABS)
9.5.4.2_E.1.1 Test purpose
9.5.4.2_E.1.2 Test applicability
9.5.4.2_E.1.3 Minimum conformance requirements
9.5.4.2_E1.4 Test description
9.5.4.2_E.1.4.1 Initial conditions
9.5.4.2_E.1.4.2 Test procedure
9.5.4.2_E.1.4.3 Message contents
9.5.4.2_E.1.5 Test requirement
9.5.5 RI Reporting (with CSI processes)
9.5.5.1_F FDD RI Reporting with CSI processes for CoMP
9.5.5.1_F.1 FDD RI Reporting with Single CSI process for CoMP
9.5.5.1_F.1.1 Test purpose
9.5.5.1_F.1.2 Test applicability
9.5.5.1_F.1.3 Minimum conformance requirements
9.5.5.1_F.1.4 Test description
9.5.5.1_F.1.4.1 Initial conditions
9.5.5.1_F.1.4.2 Test procedure
9.5.5.1_F.1.4.3 Message contents
9.5.5.1_F.1.5 Test requirement
9.5.5.1_F.2 FDD RI Reporting with Multiple CSI processes for CoMP
9.5.5.1_F.2.1 Test purpose
9.5.5.1_F.2.2 Test applicability
9.5.5.1_F.2.3 Minimum conformance requirements
9.5.5.1_F.2.4 Test description
9.5.5.1_F.2.4.1 Initial conditions
9.5.5.1_F.2.4.2 Test procedure
9.5.5.1_F.2.4.3 Message contents
9.5.5.1_F.2.5 Test requirement
9.5.5.2_F TDD RI Reporting with CSI processes for CoMP
9.5.5.2_F.1 TDD RI Reporting with Single CSI process for CoMP
9.5.5.2_F.1.1 Test purpose
9.5.5.2_F.1.2 Test applicability
9.5.5.2_F.1.3 Minimum conformance requirements
9.5.5.2_F.1.4 Test description
9.5.5.2_F.1.4.1 Initial conditions
9.5.5.2_F.1.4.2 Test procedure
9.5.5.2_F.1.4.3 Message contents
9.5.5.2_F.1.5 Test requirement
9.5.5.2_F.2 TDD RI Reporting with Multiple CSI processes for CoMP
9.5.5.2_F.2.1 Test purpose
9.5.5.2_F.2.2 Test applicability
9.5.5.2_F.2.3 Minimum conformance requirements
9.5.5.2_F.2.4 Test description
9.5.5.2_F.2.4.1 Initial conditions
9.5.5.2_F.2.4.2 Test procedure
9.5.5.2_F.2.4.3 Message contents
9.5.5.2_F.2.5 Test requirement
9.6 Additional requirements for carrier aggregation
9.6.1 Periodic reporting on multiple cells (Cell-Specific Reference Symbols)
9.6.1.1_A FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA
9.6.1.1_A.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA(2DL CA)
9.6.1.1_A.1.1 Test purpose
9.6.1.1_A.1.2 Test applicability
9.6.1.1_A.1.3 Minimum conformance requirements
9.6.1.1_A.1.4 Test description
9.6.1.1_A.1.4.1 Initial conditions
9.6.1.1_A.1.4.2 Test procedure
9.6.1.1_A.1.4.3 Message contents
9.6.1.1_A.1.5 Test requirement
9.6.1.1_A.2 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (3DL CA)
9.6.1.1_A.2.1 Test purpose
9.6.1.1_A.2.2 Test applicability
9.6.1.1_A.2.3 Minimum conformance requirements
9.6.1.1_A.2.4 Test description
9.6.1.1_A.2.4.1 Initial conditions
9.6.1.1_A.2.4.2 Test procedure
9.6.1.1_A.2.4.3 Message contents
9.6.1.1_A.2.5 Test requirement
9.6.1.1_A.3 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (4DL CA)
9.6.1.1_A.3.1 Test purpose
9.6.1.1_A.3.2 Test applicability
9.6.1.1_A.3.3 Minimum conformance requirements
9.6.1.1_A.3.4 Test description
9.6.1.1_A.3.4.1 Initial conditions
9.6.1.1_A.3.4.2 Test procedure
9.6.1.1_A.3.5 Test requirement
9.6.1.1_A.4 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (5DL CA)
9.6.1.1_A.4.1 Test purpose
9.6.1.1_A.4.2 Test applicability
9.6.1.1_A.4.3 Minimum conformance requirements
9.6.1.1_A.4.4 Test description
9.6.1.1_A.4.4.1 Initial conditions
9.6.1.1_A.4.4.2 Test procedure
9.6.1.1_A.4.4.3 Message contents
9.6.1.1_A.4.5 Test requirement
9.6.1.2_A TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA
9.6.1.2_A.1 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (2DL CA)
9.6.1.2_A.1.1 Test purpose
9.6.1.2_A.1.2 Test applicability
9.6.1.2_A.1.3 Minimum conformance requirements
9.6.1.2_A.1.4 Test description
9.6.1.2_A.1.4.1 Initial conditions
9.6.1.2_A.1.4.2 Test procedure
9.6.1.2_A.1.4.3 Message contents
9.6.1.2_A.1.5 Test requirement
9.6.1.2_A.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (3DL CA)
9.6.1.2_A.2.1 Test purpose
9.6.1.2_A.2.2 Test applicability
9.6.1.2_A.2.3 Minimum conformance requirements
9.6.1.2_A.2.4 Test description
9.6.1.2_A.2.4.1 Initial conditions
9.6.1.2_A.2.4.2 Test procedure
9.6.1.2_A.2.5 Test requirement
9.6.1.2_A.3 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (4DL CA)
9.6.1.2_A.3.1 Test purpose
9.6.1.2_A.3.2 Test applicability
9.6.1.2_A.3.3 Minimum conformance requirements
9.6.1.2_A.3.4 Test description
9.6.1.2_A.3.4.1 Initial conditions
9.6.1.2_A.3.4.2 Test procedure
9.6.1.2_A.3.5 Test requirement
9.6.1.2_A.4 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for CA (5DL CA)
9.6.1.2_A.4.1 Test purpose
9.6.1.2_A.4.2 Test applicability
9.6.1.2_A.4.3 Minimum conformance requirements
9.6.1.2_A.4.4 Test description
9.6.1.2_A.4.4.1 Initial conditions
9.6.1.2_A.4.4.2 Test procedure
9.6.1.2_A.4.5 Test requirement
9.6.1.3 TDD-FDD CA for FDD PCell
9.6.1.3.1 TDD FDD CA CQI Reporting under AWGN conditions ΠPUCCH 1-0 for FDD PCell (2DL CA)
9.6.1.3.1.2 Test applicability
9.6.1.3.1.3 Minimum conformance requirements
9.6.1.3.1.4 Test description
9.6.1.3.1.4.1 Initial conditions
9.6.1.3.1.4.2 Test procedure
9.6.1.3.1.4.3 Message contents
9.6.1.3.1.5 Test requirement
9.6.1.3.2 TDD FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for FDD PCell (3DL CA)
9.6.1.3.2.1 Test purpose
9.6.1.3.2.2 Test applicability
9.6.1.3.2.3 Minimum conformance requirements
9.6.1.3.2.4 Test description
9.6.1.3.2.4.1 Initial conditions
9.6.1.3.2.4.2 Test procedure
9.6.1.3.2.5 Test requirement
9.6.1.3.3 TDD FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for FDD PCell (4DL CA)
9.6.1.3.3.1 Test purpose
9.6.1.3.3.2 Test applicability
9.6.1.3.3.3 Minimum conformance requirements
9.6.1.3.3.4 Test description
9.6.1.3.3.4.1 Initial conditions
9.6.1.3.3.4.2 Test procedure
9.6.1.3.3.5 Test requirement
9.6.1.3.4 TDD FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for FDD PCell (5DL CA)
9.6.1.3.4.1 Test purpose
9.6.1.3.4.2 Test applicability
9.6.1.3.4.3 Minimum conformance requirements
9.6.1.3.4.4 Test description
9.6.1.3.4.4.1 Initial conditions
9.6.1.3.4.4.2 Test procedure
9.6.1.3.4.5 Test requirement
9.6.1.4 TDD-FDD CA for TDD PCell
9.6.1.4.1 TDD FDD CA CQI Reporting under AWGN conditions ΠPUCCH 1-0 for TDD PCell (2DL CA)
9.6.1.4.1.2 Test applicability
9.6.1.4.1.3 Minimum conformance requirements
9.6.1.4.1.4 Test description
9.6.1.4.1.4.1 Initial conditions
9.6.1.4.1.4.2 Test procedure
9.6.1.4.1.4.3 Message contents
9.6.1.4.1.5 Test requirement
9.6.1.4.2 TDD FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for TDD PCell (3DL CA)
9.6.1.4.2.1 Test purpose
9.6.1.4.2.2 Test applicability
9.6.1.4.2.3 Minimum conformance requirements
9.6.1.4.2.4 Test description
9.6.1.4.2.4.1 Initial conditions
9.6.1.4.2.4.2 Test procedure
9.6.1.4.2.5 Test requirement
9.6.1.4.3 TDD FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for TDD PCell (4DL CA)
9.6.1.4.3.1 Test purpose
9.6.1.4.3.2 Test applicability
9.6.1.4.3.3 Minimum conformance requirements
9.6.1.4.3.4 Test description
9.6.1.4.3.4.1 Initial conditions
9.6.1.4.3.4.2 Test procedure
9.6.1.4.3.5 Test requirement
9.6.1.4.4 TDD FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 for TDD PCell (5DL CA)
9.6.1.4.4.1 Test purpose
9.6.1.4.4.2 Test applicability
9.6.1.4.4.3 Minimum conformance requirements
9.6.1.4.4.4 Test description
9.6.1.4.4.4.1 Initial conditions
9.6.1.4.4.4.2 Test procedure
9.6.1.4.4.5 Test requirement
9.7 CSI reporting for UE DL category 0
9.7.1 CQI reporting definition under AWGN conditions
9.7.1.1 FDD and Half duplex FDD CQI reporting definition under AWGN conditions for UE category 0
9.7.1.1.1 Test purpose
9.7.1.1.2 Test applicability
9.7.1.1.3 Minimum conformance requirements
9.7.1.1.4 Test description
9.7.1.1.5 Test requirement
9.7_1.1.1 FDD CQI reporting under AWGN conditions ΠPUCCH 1-0 for UE category 1bis
9.7_1.1.1.1 Test purpose
9.7_1.1.1.2 Test applicability
9.7_1.1.1.3 Minimum conformance requirements
9.7_1.1.1.4 Test description
9.7_1.1.1.5 Test requirement
9.7_1.1.2 TDD CQI reporting under AWGN conditions - PUCCH 1-0 for UE category 1bis
9.7_1.1.2.1 Test purpose
9.7_1.1.2.2 Test applicability
9.7_1.1.2.3 Minimum conformance requirements
9.7_1.1.2.4 Test description
9.7_1.1.2.5 Test requirement
9.7_1.1.3 FDD CQI reporting under fading conditions - PUSCH 3-0 for UE category 1bis
9.7_1.1.3.1 Test purpose
9.7_1.1.3.2 Test applicability
9.7_1.1.3.3 Minimum conformance requirements
9.7_1.1.3.4 Test description
9.7_1.1.3.5 Test requirement
9.7_1.1.4 TDD CQI reporting under fading conditions - PUSCH 3-0 for UE category 1bis
9.7_1.1.4.1 Test purpose
9.7_1.1.4.2 Test applicability
9.7_1.1.4.3 Minimum conformance requirements
9.7_1.1.4.4 Test description
9.7_1.1.4.5 Test requirement
9.7.1.2 TDD CQI reporting definition under AWGN conditions for UE category 0
9.7.1.2.1 Test purpose
9.7.1.2.2 Test applicability
9.7.1.2.3 Minimum conformance requirements
9.7.1.2.4 Test description
9.7.1.2.5 Test requirement
9.7_1.1.2 TDD CQI reporting under AWGN conditions - PUCCH 1-0 for UE category 1bis
9.7_1.1.2.1 Test purpose
9.7_1.1.2.2 Test applicability
9.7_1.1.2.3 Minimum conformance requirements
9.7_1.1.2.4 Test description
9.7_1.1.2.5 Test requirement
9.7.2 CQI reporting under fading conditions
9.7.2.1 FDD and Half duplex FDD CQI reporting definition under fading conditions for UE category 0
9.7.2.1.1 Test purpose
9.7.2.1.2 Test applicability
9.7.2.1.3 Minimum conformance requirements
9.7.2.1.4 Test description
9.7.2.1.5 Test requirement
9.7.2.2 TDD CQI reporting definition under fading conditions for UE category 0
9.7.2.2.1 Test purpose
9.7.2.2.2 Test applicability
9.7.2.2.3 Minimum conformance requirements
9.7.2.2.4 Test description
9.7.2.2.5 Test requirement
9.8 CSI reporting (UE supporting coverage enhancement)
9.8.1 CQI reporting definition under AWGN conditions
9.8.1.1 FDD and Half duplex FDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement
9.8.1.1.4 Test description
9.8.1.2 TDD CQI reporting definition under AWGN conditions for UE supporting coverage enhancement
9.8.1.2.4 Test description
9.8.2 UE-selected subband CQI
9.8.2.1 FDD and half-duplex FDD UE-selected subband CQI for UE supporting coverage enhancement
9.8.2.1.4 Test description
9.8.2.2 TDD UE-selected subband CQI for UE supporting coverage enhancement
9.8.2.2.4 Test description
9.9 CSI reporting for 4Rx UE
9.9.1 CQI Reporting under AWGN conditions
9.9.1.1 CQI reporting under AWGN conditions - PUCCH 1-0 with Rank 1 (Cell-Specific Reference Symbols)
9.9.1.1.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 with Rank 1 1x4
9.9.1.1.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-0 with Rank 1 1x4
9.9.1.1.2.5 Test requirement
9.9.1.2 CQI reporting under AWGN conditions - PUCCH 1-1 with Rank 2 (CSI Reference Symbols)
9.9.1.2.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 with Rank 2 4x4
9.9.1.2.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 with Rank 2 8x4
9.9.1.3 CQI Reporting under AWGN conditions - PUCCH 1-1 (Cell-Specific Reference Symbols)
9.9.1.3.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 with rank 4 4x4
9.9.1.3.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 with rank 4 4x4
9.9.1.4 CQI reporting under AWGN conditions - PUCCH 1-1 with Rank 3 (CSI Reference Symbols)
9.9.1.4.1 FDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 with Rank 3 4x4
9.9.1.4.2 TDD CQI Reporting under AWGN conditions ΠPUCCH 1-1 with Rank 3 4x4
9.9.2 CQI Reporting under fading conditions
9.9.2.1 CQI Reporting under fading conditions - PUCCH 1-0 (Cell-Specific Reference Symbols) for Enhanced Performance Requiremen
9.9.2.1.1 FDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A 1x4
9.9.2.1.2 TDD CQI Reporting under fading conditions - PUCCH 1-0 - Enhanced Performance Requirement Type A 1x4
9.9.2.2 CQI Reporting under fading conditions - PUCCH 1-1 (CSI Reference Symbol) for Enhanced Performance Requirement Type A
9.9.2.2.1 FDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A 2x4
9.9.2.2.2 TDD CQI Reporting under fading conditions - PUCCH 1-1 - Enhanced Performance Requirement Type A 2x4
9.9.3 Reporting of Precoding Matrix Indicator (PMI) for 4Rx UE
9.9.3.1 PMI Reporting ΠPUSCH 3-1 (Single PMI) (Cell-Specific Reference Symbols)
9.9.3.1.1 TDD PMI Reporting ΠPUSCH 3-1 (Single PMI) 8x4
9.9.4 Reporting of Rank Indicator (RI)
9.9.4.1 RI ReportingΠPUCCH 1-1 4x4
9.9.4.1.1 FDD RI ReportingΠPUCCH 1-1 4x4
9.9.4.1.1.1 Test purpose
9.9.4.1.1.2 Test applicability
9.9.4.1.1.3 Minimum conformance requirements
9.9.4.1.1.4 Test description
9.9.4.1.1.5 Test requirement
9.9.4.1.2 TDD RI ReportingΠPUSCH 3-1 4x4
9.9.4.1.2.1 Test purpose
9.9.4.1.2.2 Test applicability
9.9.4.1.2.3 Minimum conformance requirements
9.9.4.1.2.4 Test description
9.9.4.1.2.5 Test requirement
9.9.4.2 RI Reporting- PUCCH 1-1 for eDL-MIMO 4x4
9.9.4.2.1 FDD RI Reporting- PUCCH 1-1 for eDL-MIMO 4x4
9.9.4.2.1.1 Test purpose
9.9.4.2.1.2 Test applicability
9.9.4.2.1.3 Minimum conformance requirements
9.9.4.2.1.4 Test description
9.9.4.2.1.5 Test requirement
9.9.4.2.2 TDD RI Reporting- PUCCH 1-1 for eDL-MIMO 4x4
9.9.4.2.2.2 Test applicability
9.9.4.2.2.3 Minimum conformance requirements
9.9.4.2.2.4 Test description
9.9.4.2.2.5 Test requirement
9.10 Reporting of CSI-RS Resource Indicator (CRI)
9.10.1 CSI-RS Resource Indicator Reporting (PUSCH 3-1)
9.10.1.1 FDD CSI-RS Resource Indicator Reporting ΠPUSCH 3-1
9.10.1.1.1 Test purpose
9.10.1.1.2 Test applicability
9.10.1.1.3 Minimum conformance requirements
9.10.1.1.4 Test description
9.10.1.1.5 Test requirement
9.10.1.2 TDD CSI-RS Resource Indicator Reporting ΠPUSCH 3-1
9.10.1.2.1 Test purpose
9.10.1.2.2 Test applicability
9.10.1.2.3 Minimum conformance requirements
9.10.1.2.4 Test description
9.10.1.2.5 Test requirement
10 MBMS Performance
10.1 FDD MBMS performance (Fixed Reference Channel)
10.1.1 Test purpose
10.1.2 Test applicability
10.1.3 Minimum conformance requirements
10.1.4 Test description
10.1.4.1 Initial conditions
10.1.4.2 Test procedure
10.1.4.3 Message contents
10.1.5 Test requirement
10.1_1 FDD MBMS performance (Fixed Reference Channel) (Release 13 and forward)
10.1_1.1 Test purpose
10.1_1.2 Test applicability
10.1_1.3 Minimum conformance requirements
10.1_1.4 Test description
10.1_1.4.1 Initial conditions
10.1_1.4.2 Test procedure
10.1_1.4.3 Message contents
10.1_1.5 Test requirement
10.2 TDD MBMS performance (Fixed Reference Channel)
10.2.1 Test purpose
10.2.2 Test applicability
10.2.3 Minimum conformance requirements
10.2.4 Test description
10.2.4.1 Initial conditions
10.2.4.2 Test procedure
10.2.4.3 Message contents
10.2.5 Test requirement
10.2_1 TDD MBMS performance (Fixed Reference Channel) (Release 13 and forward)
10.2.1 Test purpose
10.2.2 Test applicability
10.2.3 Minimum conformance requirements
10.2.4 Test description
10.2.4.1 Initial conditions
10.2_1.4.2 Test procedure
10.2.4.3 Message contents
10.2_1.5 Test requirement
11 Performance Requirement (ProSe Direct Discovery)
11.1 General
11.1.1 Applicability of requirements
11.1.2 Reference DRX configuration
11.2 Demodulation of PSDCH (single link performance)
11.2.1 FDD PSDCH Single Link Performance (ProSe Direct Discovery)
11.2.1.1 Test Purpose
11.2.1.2 Test Applicability
11.2.1.3 Minimum Conformance Requirements
11.2.1.4 Test Description
11.2.1.4.1 Initial Conditions
11.2.1.4.2 Test Procedure
11.2.1.4.3 Message Contents
11.2.1.5 Test Requirement
11.2.2 TDD PSDCH Single Link Performance (ProSe Direct Discovery)
11.2.2.1 Test Purpose
11.2.2.2 Test Applicability
11.2.2.3 Minimum Conformance Requirements
11.2.2.4 Test Description
11.2.2.4.1 Initial Conditions
11.2.2.4.2 Test Procedure
11.2.2.4.3 Message Contents
11.2.2.5 Test Requirement
11.3 Power imbalance performance with two links
11.3.1 FDD Power imbalance performance with two links
11.3.1.1 Test Purpose
11.3.1.2 Test Applicability
11.3.1.3 Minimum Conformance Requirements
11.3.1.4 Test Description
11.3.1.5 Test Requirement
11.3.2 TDD Power imbalance performance with two links
11.3.2.1 Test Purpose
11.3.2.2 Test Applicability
11.3.2.3 Minimum Conformance Requirements
11.3.2.4 Test Description
11.3.2.5 Test Requirement
11.4 Multiple timing reference test
11.4.1 FDD Multiple timing reference test
11.4.1.1 Test Purpose
11.4.1.2 Test Applicability
11.4.1.3 Minimum Conformance Requirements
11.4.1.4 Test Description
11.4.1.4.1 Initial Conditions
11.4.1.4.2 Test Procedure
11.4.1.4.3 Message Contents
11.4.1.5 Test Requirement
11.5 Maximum Sidelink processes test
11.5.1 FDD maximum Sidelink processes test (ProSe Direct Discovery)
11.5.1.1 Test Purpose
11.5.1.2 Test Applicability
11.5.1.3 Minimum Conformance Requirements
11.5.1.4 Test Description
11.5.1.4.1 Initial Conditions
11.5.1.4.2 Test Procedure
11.5.1.4.3 Message Contents
11.5.1.5 Test Requirement
11.5.2 TDD maximum Sidelink processes test (ProSe Direct Discovery)
11.5.2.1 Test Purpose
11.5.2.2 Test Applicability
11.5.2.3 Minimum Conformance Requirements
11.5.2.4 Test Description
11.5.2.4.1 Initial Conditions
11.5.2.4.2 Test Procedure
11.5.2.4.3 Message Contents
11.5.2.5 Test Requirement
12 Performance requirement (ProSe Direct Communication)
12.1 General
12.1.1 Applicability of requirements
12.1.2 Reference DRX configuration
12.2 Demodulation of PSSCH
12.2.1 FDD PSSCH Single Link Performance for ProSe Direct communication
12.2.1.1 Test Purpose
12.2.1.2 Test Applicability
12.2.1.3 Minimum Conformance Requirements
12.2.1.4 Test Description
12.2.1.4.1 Initial Conditions
12.2.1.4.2 Test Procedure
12.2.1.4.3 Message Contents
12.2.1.5 Test Requirement
12.3 Demodulation of PSCCH (single link performance)
12.4 Demodulation of PSBCH (single link performance)
12.5 Power imbalance performance with two links
12.5.1 FDD Power imbalance performance with two links
12.5.1.1 Test Purpose
12.5.1.2 Test Applicability
12.5.1.3 Minimum Conformance Requirements
12.5.1.4 Test Description
12.5.1.4.1 Initial Conditions
12.5.1.4.2 Test Procedure
12.5.1.4.3 Message Contents
12.5.1.5 Test Requirement
12.6 Multiple timing reference test
12.7 Maximum Sidelink processes test
12.7.1 FDD Maximum Sidelink Processes for ProSe Direct communication
12.7.1.1 Test Purpose
12.7.1.2 Test Applicability
12.7.1.3 Minimum Conformance Requirements
12.7.1.4 Test Description
12.7.1.4.1 Initial Conditions
12.7.1.4.2 Test Procedure
12.7.1.4.3 Message Contents
12.7.1.5 Test Requirement
13 FFS
14 Performance requirement (V2X Sidelink Communication)
14.1 General
14.1.1 Applicability of requirements
14.2 Demodulation of PSSCH / Non-concurrent with E-UTRA uplink transmissions
14.2.1 Test Purpose
14.2.2 Test Applicability
14.2.3 Minimum Conformance Requirements
14.2.4 Test Description
14.2.5 Test Requirements
14.3 Demodulation of PSCCH / Non-concurrent with E-UTRA uplink transmissions
14.3.1 Test Purpose
14.3.2 Test Applicability
14.3.3 Minimum Conformance Requirements
14.3.4 Test Description
14.3.5 Test Requirements
14.4 Power imbalance performance with two links / Non-concurrent with E-UTRA uplink transmissions
14.4.1 Test Purpose
14.4.2 Test Applicability
14.4.3 Minimum Conformance Requirements
14.4.4 Test Description
14.4.5 Test Requirements
14.5 to 14.7
14.8 PSCCH/PSSCH decoding capability test / Non-concurrent with E-UTRA uplink transmissions
14.8.1 Test Purpose
14.8.2 Test Applicability
14.8.3 Minimum Conformance Requirements
14.8.4 Test Description
14.8.5 Test Requirement
Annex A (normative): Measurement Channels
A.1 General
A.2 UL reference measurement channels
A.2.1 General
A.2.1.1 Applicability and common parameters
A.2.1.2 Determination of payload size
A.2.1.3 Overview of UL reference measurement channels
A.2.2 Reference measurement channels for FDD
A.2.2.1 Full RB allocation
A.2.2.1.1 QPSK
A.2.2.1.2 16-QAM
A.2.2.1.3 64-QAM
A.2.2.1.4 256 QAM
A.2.2.2 Partial RB allocation
A.2.2.2.1 QPSK
A.2.2.2.2 16-QAM
A.2.2.2.3 64-QAM
A.2.2.2.4 256 QAM
A.2.2.3 Reference measurement channels for sustained downlink data rate provided by lower layers
A.2.3 Reference measurement channels for TDD
A.2.3.1 Full RB allocation
A.2.3.1.1 QPSK
A.2.3.1.2 16-QAM
A.2.3.1.3 64-QAM
A.2.3.1.4 256 QAM
A.2.3.2 Partial RB allocation
A.2.3.2.1 QPSK
A.2.3.2.2 16-QAM
A.2.3.2.3 64-QAM
A.2.3.2.4 256 QAM
A.2.3.3 Reference measurement channels for sustained downlink data rate provided by lower layers
A.2.4 Reference measurement channels for category NB1
A.2.5 Reference measurement channels for LAA
A.2.5.1 Full RB allocation
A.2.5.1.1 QPSK
A.2.5.1.2 16QAM
A.2.5.1.3 64QAM
A.2.5.2 Partial RB allocation
A.2.5.2.1 QPSK
A.2.5.2.2 16QAM
A.2.5.2.3 64QAM
A.3 DL reference measurement channels
A.3.1 General
A.3.1.1 Overview of DL reference measurement channels
A.3.2 Reference measurement channel for receiver characteristics
A.3.2A Downlink Reference measurement channel for TX characteristics
A.3.2B Downlink Reference measurement channel for ProSe testing
A.3.3 Reference measurement channel for PDSCH performance requirements (FDD)
A.3.3.1 Single-antenna transmission (Common Reference Symbols)
A.3.3.2 Multi-antenna transmission (Common Reference Symbols)
A.3.3.2.1 Two antenna ports
A.3.3.2.2 Four antenna ports
A.3.3.3 Reference Measurement Channel for UE-Specific Reference Symbols
A.3.3.3.0 Two antenna ports (no CSI-RS)
A.3.3.3.1 Two antenna port (CSI-RS)
A.3.3.3.2 Four antenna ports (CSI-RS)
A.3.3.3.2A Eight antenna ports (CSI-RS)
A.3.3.3.3 Twelve antenna port (CSI-RS)
A.3.4 Reference measurement channel for PDSCH performance requirements (TDD)
A.3.4.1 Single-antenna transmission (Common Reference Symbols)
A.3.4.2 Multi-antenna transmission (Common Reference Symbols)
A.3.4.2.1 Two antenna ports
A.3.4.2.2 Four antenna ports
A.3.4.3 Reference Measurement Channels for UE-Specific Reference Symbols
A.3.4.3.3 Two antenna ports (CSI-RS)
A.3.4.3.4 Four antenna ports (CSI-RS)
A.3.4.3.5 Eight antenna ports (CSI-RS)
A.3.4.3.6 Twelve antenna ports (CSI-RS)
A.3.5 Reference measurement channels for PDCCH/PCFICH performance requirements
A.3.5.1 FDD
A.3.5.2 TDD
A.3.5.3 LAA
A.3.6 Reference measurement channels for PHICH performance requirements
A.3.7 [FFS]
A.3.8 Reference measurement channels for MBMS performance requirements
A.3.8.1 FDD
A.3.8.2 TDD
A.3.9 Reference measurement channels for sustained downlink data rate provided by lower layers
A.3.9.1 FDD
A.3.9.2 TDD
A.3.9.3 FDD (EPDCCH scheduling)
A.3.9.4 TDD (EPDCCH scheduling)
A.3.10 Reference Measurement Channels for EPDCCH performance requirements
A.3.10.1 FDD
A.3.10.2 TDD
A.3.11 Reference Measurement Channels for MPDCCH performance requirements
A.3.11.1 FDD and half-duplex FDD
A.3.11.2 TDD
A.3.12 Reference measurement channels for NPDSCH performance requirements
A.3.15 Reference Measurement Channels for LAA SCell with frame structure Type-3
A.3.15.1 Multi-antenna transmission (Common Reference Symbols)
A.3.15.1.1 Four antenna ports
A.3.15.2 Reference Measurement Channel for UE-Specific Reference Symbols
A.3.15.2.1 Two antenna ports (CSI-RS)
A.4 CQI reference measurement channels
A.4.1 Additional CSI reference measurement channels
A.5 OFDMA Channel Noise Generator (OCNG)
A.5.1 OCNG Patterns for FDD
A.5.1.1 OCNG FDD pattern 1: One sided dynamic OCNG FDD pattern
A.5.1.2 OCNG FDD pattern 2: Two sided dynamic OCNG FDD pattern
A.5.1.3 OCNG FDD pattern 3: 49 RB OCNG allocation with MBSFN in 10 MHz
A.5.1.4 OCNG FDD pattern 4: One sided dynamic OCNG FDD pattern for MBMS transmission
A.5.1.5 OCNG FDD pattern 5: One sided dynamic 16QAM modulated OCNG FDD pattern
A.5.1.6 OCNG FDD pattern 6: dynamic OCNG FDD pattern when user data is in 2 non-contiguous blocks
A.5.1.8 OCNG FDD pattern 8: One sided dynamic OCNG FDD pattern for TM10 transmission
A.5.2 OCNG Patterns for TDD
A.5.2.1 OCNG TDD pattern 1: One sided dynamic OCNG TDD pattern
A.5.2.2 OCNG TDD pattern 2: Two sided dynamic OCNG TDD pattern
A.5.2.3 OCNG TDD pattern 3: 49 RB OCNG allocation with MBSFN in 10 MHz
A.5.2.4 OCNG TDD pattern 4: One sided dynamic OCNG TDD pattern for MBMS transmission
A.5.2.5 OCNG TDD pattern 5: One sided dynamic 16QAM modulated OCNG TDD pattern
A.5.2.6 OCNG TDD pattern 6: dynamic OCNG TDD pattern when user data is in 2 non-contiguous blocks
A.5.2.8 OCNG TDD pattern 8: One sided dynamic OCNG TDD pattern for TM10 transmission
A.5.3 OCNG Patterns for Narrowband IoT
A.5.3.1 Narrowband IoT OCNG pattern 1
A.5.4 OCNG Patterns for frame structure type
A.5.4.1 OCNG FS3 pattern 1: One sided dynamic OCNG frame structure type 3 pattern
A.5.4.2 OCNG FS3 pattern 2: Two sided dynamic OCNG frame structure 3 pattern
A.6 Sidelink reference measurement channels
A.6.1 General
A.6.2 Reference measurement channel for receiver characteristics
A.6.3 Reference measurement channels for PSDCH performance requirements
A.6.4 Reference measurement channels for PSCCH performance requirements
A.6.5 Reference measurement channels for PSSCH performance requirements
A.6.6 Reference measurement channels for PSBCH performance requirements
A.7 Sidelink reference resource pool configurations
A.7.1 Reference resource pool configurations for ProSe Direct Discovery demodulation tests
A.7.1.1 FDD
A.7.1.2 TDD
A.7.2 Reference resource pool configurations for ProSe Direct Communication demodulation tests
A.7.2.1 FDD
A.8 V2X reference measurement channels
A.8.1 General
A.8.2 Reference measurement channel for receiver characteristics
A.8.3 Reference measurement channel for transmitter characteristics
A.8.4 Reference measurement for PSCCH performance requirements
A.8.5 Reference measurement for PSSCH performance requirements
A.8.6 Reference measurement for PSBCH performance requirements
A.9 V2X reference resource pool configurations
Annex B (normative): Propagation Conditions
B.0 No interference
B.1 Static propagation condition
B.1.1 Definition of Additive White Gaussian Noise (AWGN) Interferer
B.2 Multi-path fading Propagation Conditions
B.2.1 Delay profiles
B.2.2 Combinations of channel model parameters
B.2.3 MIMO Channel Correlation Matrices
B.2.3.1 Definition of MIMO Correlation Matrices
B.2.3.2 MIMO Correlation Matrices at High, Medium and Low Level
B.2.3A MIMO Channel Correlation Matrices using cross polarized antennas
B.2.3A.1 Definition of MIMO Correlation Matrices using cross polarized antennas
B.2.3A.2 Spatial Correlation Matrices using cross polarized antennas at eNB and UE sides
B.2.3A.2.1 Spatial Correlation Matrices at eNB side
B.2.3A.2.2 Spatial Correlation Matrices at UE side
B.2.3A.3 MIMO Correlation Matrices using cross polarized antennas
B.2.3A.4 Beam steering approach
B.2.4 Propagation conditions for CQI tests
B.2.5 FFS
B.2.6 MBSFN Propagation Channel Profile
B.3 High speed train scenario
B.3A HST-SFN scenario
B.4 Beamforming Model
B.4.1 Single-layer random beamforming (Antenna port 5, 7 or 8)
B.4.2 Dual-layer random beamforming (antenna ports 7 and 8)
B.4.3 Generic beamforming model (antenna ports 7-14)
B.4.4 Random beamforming for EPDCCH distributed transmission (Antenna port 107 and 109)
B.4.5 Random beamforming for EPDCCH localized transmission (Antenna port 107, 108, 109 or 110)
B.4.6 Beamforming model for CRI test
B.5 Interference models for enhanced performance requirements Type-A
B.5.1 Dominant interferer proportion
B.5.2 Transmission mode 3 interference model
B.5.3 Transmission mode 4 interference model
B.5.4 Transmission mode 9 interference model
B.6 Interference models for enhanced performance requirements Type-B
B.6.1 Transmission mode 2 interference model
B.6.2 Transmission mode 3 interference model
B.6.3 Transmission mode 4 interference model
B.6.4 Transmission mode 9 interference model
B.6.5 CRS interference model
B.6.6 Random interference model
B.7 FFS
B.8 Burst transmission models for Frame structure type 3
B.8.1 Burst transmission model for one LAA SCell
Annex C (normative): Downlink Physical Channels
C.0 Downlink signal levels
C.1 General
C.2 Set-up
C.3 Connection
C.3.0 Measurement of Transmitter Characteristics
C.3.1 Measurement of Receiver Characteristics
C.3.2 Measurement of Performance requirements
C.3.3 Aggressor cell power allocation for Measurement of Performance Requirements when ABS is Configured
C.3.4 Power Allocation for Measurement of Performance Requirements when Quasi Co-location Type B: same Cell ID
C.3.5 Simplified CA testing method
Annex D (normative): Characteristics of the Interfering Signal
D.1 General
D.2 Interference signals
Annex E (normative): Global In-Channel TX-Test
E.1 General
E.2 Signals and results
E.2.1 Basic principle
E.2.2 Output signal of the TX under test
E.2.3 Reference signal
E.2.4 Measurement results
E.2.5 Measurement points
E.3 Signal processing
E.3.1 Pre FFT minimization process
E.3.2 Timing of the FFT window
E.3.3 Post FFT equalisation
E.4 Derivation of the results
E.4.1 EVM
E.4.2 Averaged EVM
E.4.3 In-band emissions measurement
E.4.4 EVM equalizer spectrum flatness
E.4.5 Frequency error and Carrier leakage
E.4.6 EVM of Demodulation reference symbols (EVMDMRS)
E.4.6.1 1st average for EVM DMRS
E.4.6.2 Final average for EVM DMRS
E.5 EVM and inband emissions for PUCCH
E.5.1 Basic principle
E.5.2 Output signal of the TX under test
E.5.3 Reference signal
E.5.4 Measurement results
E.5.5 Measurement points
E.5.6 Pre FFT minimization process
E.5.7 Timing of the FFT window
E.5.8 Post FFT equalisation
E.5.9 Derivation of the results
E.5.9.1 EVMPUCCH
E.5.9.2 Averaged EVMPUCCH
E.5.9.3 In-band emissions measurement
E.6 EVM for PRACH
E.6.1 Basic principle
E.6.2 Output signal of the TX under test
E.6.3 Reference signal
E.6.4 Measurement results
E.6.5 Measurement points
E.6.6 Pre FFT minimization process
E.6.7 Timing of the FFT window
E.6.8 Post FFT equalisation
E.6.9 Derivation of the results
E.6.9.1 EVMPRACH
E.6.9.2 Averaged EVMPRACH
E.7 EVM with exclusion period
E.7.1 General
E.7.2 The model
E.7.3 Illustration
E.7.4 Formula
E.8 EVM for category NB1
E.8.1 Averaged EVM
E.8.2 EVM of Demodulation reference symbols (EVMDMRS)
E.8.3 EVM for NPRACH
E.8.4 Window length for category NB1
E.9 EVM for V2X communication
E.9.1 EVM for PSSCH and PSCCH
E.9.2 EVM for PSBCH
Annex F (normative): Measurement uncertainties and Test Tolerances
F.1 Acceptable uncertainty of Test System (normative)
F.1.1 Measurement of test environments
F.1.2 Measurement of transmitter
F.1.3 Measurement of receiver
F.1.4 Measurement of performance requirements
F.1.5 Measurement of Channel State Information reporting
F.2 Interpretation of measurement results (normative)
F.3 Test Tolerance and Derivation of Test Requirements (informative)
F.3.1 Measurement of test environments
F.3.2 Measurement of transmitter
F.3.3 Measurement of receiver
F.3.4 Measurement of performance requirements
F.3.5 Measurement of Channel State Information reporting
Annex G (normative): Statistical Testing
G.1 General
G.2 Statistical testing of receiver characteristics
G.2.1 General
G.2.2 Mapping throughput to error ratio
G.2.3 Design of the test
G.2.4 Numerical definition of the pass fail limits
G.2.5 Pass fail decision rules
G.2.6 Test conditions for receiver tests
G.2A Statistical testing of receiver characteristics with CA
G.2A.1 General
G.2A.2 Mapping throughput to error ratio
G.2A.3
G.2A.4 Pass fail limits
G.2A.5 void
G.2A.6 Test conditions for receiver tests with CA
G.3 Statistical testing of Performance Requirements with throughput
G.3.1 General
G.3.2 Mapping throughput to error ratio
G.3.3 Design of the test
G.3.4 Pass Fail limit
G.3.5 Minimum Test time
G.3.6 Test conditions for receiver performance tests
G.3A Statistical testing of Performance Requirements with throughput for CA/DC/LAA
G.3A.1 General
G.3A.2 Mapping throughput to error ratio
G.3A.3 Design of the test
G.3A.4 Pass Fail limit
G.3A.5 Minimum test time
G.3A.6 Test conditions
G.4 Statistical testing of Performance Requirements with probability of misdetection
G.4.1 General
G.4.2 Mapping the UE reaction to error ratio
G.4.3 Design of the test
G.4.4 Numerical definition of the pass fail limits
G.4.5 Pass fail decision rules
G.4.6 Minimum Test time
G.4.7 Test conditions for receiver performance tests
G.5 Measuring throughput ratio
G.5.1 General
G.5.2 Establishing SNR
G.5.3 Measuring T-put
G.5.4 Number of samples for throughput ratios
G.6 Statistical testing of MBMS Performance
G.6.1 General
G.6.2 Mapping of MBMS Packet ratio to BLER
G.6.3 Design of the test
G.6.4 Test time for MBMS performance tests
G.7 Theory to derive the numbers in Table G.2.4-1 (Informative)
G.7.1 Error Ratio (ER)
G.7.2 Test Design
G.7.3 Confidence level
G.7.4 Introduction: Supplier Risk versus Customer Risk
G.7.5 Supplier Risk versus Customer Risk
G.7.6 Introduction: Standard test versus early decision concept
G.7.7 Standard test versus early decision concept
G.7.8 Selectivity
G.7.9 Design of the test
G.7.10 Simulation to derive the pass fail limits in Table G.2.4-1
G.8 Statistical Testing of V2V and V2X Performance Requirements ΠNon concurrent with E-UTRA
G.8.1 General
G.8.2 Test Method for Performance Test Cases
G.8.3 Test Time for V2V and V2X Performance Requirements with Throughput
G.8.4 Test Time for V2V and V2X Performance Requirements with Probability of Miss-Detection
Annex H (normative): Uplink Physical Channels
H.0 Uplink Signal Levels
H.0.1 Uplink Signal Levels for NB1
H.1 General
H.1.1 General for NB1
H.2 Set-up
H.2.1 Set-up for NB1
H.3 Connection
H.3.0 Measurement of Transmitter Characteristics
H.3.1 Measurement of Receiver Characteristics
H.3.2 Measurement of Performance Requirements
H.4 Connection for NB1
H.4.0 Measurement of Transmitter Characteristics
H.4.1 Measurement of Receiver Characteristics
H.4.2 Measurement of Performance Requirements
Annex I (informative): Handling requirements and tests for different releases and UE capabilities
I.1 General Considerations
I.2 Concrete scenarios
I.2.1 Tests for minimum requirements varying between releases, without introduction of new features
I.2.2 Tests for CA (Carrier aggregation)
I.2.2.1 CA Tx tests (Chapter 6)
I.2.2.2 CA Rx tests (Chapter 7)
I.2.2.3 CA Performance tests (Chapter 8)
I.2.3 Tests for UL-MIMO (Uplink Multiple Antenna Transmission)
I.2.3.1 UL-MIMO Tx tests (Chapter 6)
I.2.3.2 UL-MIMO Rx tests (Chapter 7)
I.2.4 Tests for eDL-MIMO (Enhanced Downlink Multiple Antenna Transmission)
I.2.4.1 eDL MIMO Performance tests (Chapter 8)
I.2.4.2 eDL MIMO CSI tests (Chapter 9)
I.2.5 Tests for eICIC (Enhanced Intercarrier Interference Cancellation / Coordination)
I.2.5.1 eICIC Performance tests (Chapter 8)
I.2.5.2 eICIC CSI tests (Chapter 9)
I.2.6 Tests for feICIC (Further Enhanced Non CA-based ICIC for LTE)
I.2.6.1 feICIC Performance tests (Chapter 8)
I.2.6.2 feICIC CSI tests (Chapter 9)
I.2.7 Tests for DL ComP (Downlink Coordinated Multipoint Transmission)
I.2.7.1 CoMP Performance tests (Chapter 8)
I.2.7.2 CoMP CSI tests (Chapter 9)
I.2.8 Tests for Further eDL-MIMO (Enhanced Downlink Multiple Antenna Transmission) Enhancement for LTE-A
I.2.8.1 eDL MIMO Enhancement CSI tests (Chapter 9)
I.2.9 Tests for UE category 0
I.2.9.1 UE category 0 Tx tests (Chapter 6)
I.2.9.2 UE category 0 Rx tests (Chapter 7)
I.2.9.3 UE category 0 Performance tests (Chapter 8)
I.2.9.4 UE category 0 CSI tests (Chapter 9)
I.2.9A Tests for UE category M1
I.2.9A.1 UE category M1 Tx tests (Chapter 6)
I.2.9A.2 UE category M1 Rx tests (Chapter 7)
I.2.9A.3 UE category M1 Performance tests (Chapter 8)
I.2.9A.4 UE category M1 CSI tests (Chapter 9)
I.2.9B Tests for UE category M2
I.2.9B.1 UE category M2 Tx tests (Chapter 6)
I.2.9B.2 UE category M2 Rx tests (Chapter 7)
I.2.9B.3 UE category M2 Performance tests (Chapter 8)
I.2.9B.4 UE category M2 CSI tests (Chapter 9)
I.2.10 Tests for SCE-L1 (Small Cell Enhancements-Physical layer)
I.2.10.1 SCE-L1 Receiver tests (Chapter 7)
I.2.10.2 SCE-L1 Performance tests (Chapter 8)
I.2.10.3 SCE-L1 CSI tests (Chapter 9)
I.2.11 Tests for ProSe
I.2.11.1 ProSe Tx tests (Chapter 6)
I.2.11.2 ProSe Rx tests (Chapter 7)
I.2.11.3 ProSe Performance tests (Chapter 8)
I.2.11.4 ProSe CSI tests (Chapter 9)
I.2.12 Tests for 4 Rx antenna ports
I.2.12.1 4 Rx antenna ports Rx tests (Chapter 7)
I.2.12.2 4 Rx antenna ports Performance tests (Chapter 8)
I.2.12.3 4 Rx antenna ports CSI tests (Chapter 9)
Annex J (normative): Modified MPR behaviour
J.1 Indication of modified MPR behaviour
Annex K (normative): NB-IoT Test Frequencies
K.1 NB-IoT Test frequencies for TRx Tests
K.1.1 Test frequencies selection criteria 1
K.1.2 Test frequencies selection criteria 2
K.1.3 Test frequencies selection criteria 3
K.2 NB-IoT Test frequencies for Demodulation Tests
K.2.1 Test frequencies selection criteria 1
Annex L (informative): Change history
History
ETSI TS 136 521-1 V15.5.0 (2019-07)
TECHNICAL SPECIFICATION
Evolved Universal Terrestrial Radio Access (E-UTRA);
User Equipment (UE) conformance specification;
LTE;
Radio transmission and reception;
Part 1: Conformance testing
(3GPP TS 36.521-1 version 15.5.0 Release 15)
3GPP TS 36.521-1 version 15.5.0 Release 15
1
ETSI TS 136 521-1 V15.5.0 (2019-07)
Reference
RTS/TSGR-0536521-1vf50
Keywords
LTE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
of the oneM2M Partners.
ETSI
3GPP TS 36.521-1 version 15.5.0 Release 15
2
ETSI TS 136 521-1 V15.5.0 (2019-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Legal Notice
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities. These shall be
interpreted as being references to the corresponding ETSI deliverables.
The cross reference between 3GPP and ETSI identities can be found under http://webapp.etsi.org/key/queryform.asp.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
3GPP TS 36.521-1 version 15.5.0 Release 15
3
ETSI TS 136 521-1 V15.5.0 (2019-07)
Contents
Intellectual Property Rights ................................................................................................................................ 2
Legal Notice ....................................................................................................................................................... 2
Modal verbs terminology .................................................................................................................................... 2
Foreword ......................................................................................................................................................... 119
Introduction .................................................................................................................................................... 119
1
2
3
3.1
3.2
3.3
4
4.1
4.2
Scope .................................................................................................................................................... 120
References ............................................................................................................................................ 121
Definitions, symbols and abbreviations ............................................................................................... 123
Definitions ...................................................................................................................................................... 123
Symbols .......................................................................................................................................................... 125
Abbreviations ................................................................................................................................................. 127
General ................................................................................................................................................. 130
Categorization of test requirements in CA, UL-MIMO, ProSe, Dual Connectivity, UE category 0, UE
category M1, UE category M2, UE category 1bis, UE category NB1, UE category NB2, V2X
Communication .............................................................................................................................................. 131
RF requirements in later releases ................................................................................................................... 132
5
5.1
5.2
5.2A
5.2B
5.2C
5.2D
5.2E
5.2F
5.2G
5.3
5.3A
5.3F
5.4
5.4.1
5.4.1A
5.4.1F
5.4.2
5.4.2.1
5.4.2A
5.4.2A.1
5.4.2B
5.4.2B.1
5.4.2C
5.4.2D
5.4.2D.1
5.4.2F
5.4.2G
5.4.2G.1
5.4.3
5.4.3A
5.4.3F
5.4.4
5.4.4F
Frequency bands and channel arrangement .......................................................................................... 133
General ........................................................................................................................................................... 133
Operating bands .............................................................................................................................................. 133
Operating bands for CA ................................................................................................................................. 135
Operating bands for UL-MIMO ..................................................................................................................... 150
Operating bands for Dual Connectivity .......................................................................................................... 150
Operating bands for ProSe.............................................................................................................................. 151
Operating bands for UE category 0, UE category M1, M2 and UE category 1bis ......................................... 152
Operating bands for UE category NB1 and NB2 ........................................................................................... 152
Operating bands for V2X Communication ..................................................................................................... 153
TX–RX frequency separation ......................................................................................................................... 153
TX–RX frequency separation for CA ............................................................................................................. 154
TX–RX frequency separation for category NB1 and NB2 ............................................................................. 154
Channel arrangement ...................................................................................................................................... 155
Channel spacing ........................................................................................................................................ 155
Channel spacing for CA ............................................................................................................................ 155
Channel spacing for UE category NB1 and NB2...................................................................................... 155
Channel bandwidth ................................................................................................................................... 155
Channel bandwidths per operating band ............................................................................................. 156
Channel bandwidth for CA ....................................................................................................................... 159
Channel bandwidths per operating band for CA ................................................................................. 161
Channel bandwidth for UL-MIMO ........................................................................................................... 247
Channel bandwidths per operating band for UL- MIMO .................................................................... 247
Channel bandwidth for Dual Connectivity ............................................................................................... 248
Channel bandwidth for ProSe ................................................................................................................... 248
Channel bandwidths per operating band for ProSe ............................................................................. 248
Channel bandwidth for category NB1 and category NB2......................................................................... 248
Channel bandwidth for V2X Communication .......................................................................................... 249
Channel bandwidths per operating band for V2X Communication .................................................... 249
Channel raster ........................................................................................................................................... 251
Channel raster for CA ............................................................................................................................... 251
Channel raster for UE category NB1 and NB2 ......................................................................................... 251
Carrier frequency and EARFCN ............................................................................................................... 251
Carrier frequency and EARFCN for category NB1 and NB2 ................................................................... 253
6
6.1
Transmitter Characteristics ................................................................................................................... 254
General ........................................................................................................................................................... 254
ETSI
3GPP TS 36.521-1 version 15.5.0 Release 15
4
ETSI TS 136 521-1 V15.5.0 (2019-07)
6.2
6.2.1
6.2.2
6.2.2.1
6.2.2.2
6.2.2.3
6.2.2.4
6.2.2.4.1
6.2.2.4.2
6.2.2.4.3
6.2.2.5
6.2.2_1
6.2.2_1.1
6.2.2_1.2
6.2.2_1.3
6.2.2_1.4
6.2.2_1.5
6.2.2A
6.2.2A.0
6.2.2A.1
6.2.2A.1.1
6.2.2A.1.2
6.2.2A.1.3
6.2.2A.1.4
6.2.2A.1.5
6.2.2A.1_3
6.2.2A.1_3.1
6.2.2A.1_3.2
6.2.2A.1_3.3
6.2.2A.1_3.4
6.2.2A.1_3.5
6.2.2A.2
6.2.2A.2.1
6.2.2A.2.2
6.2.2A.2.3
6.2.2A.2.4
6.2.2A.2.5
6.2.2A.3
6.2.2A.4
6.2.2A.4.1
6.2.2A.4.2
6.2.2A.4.3
6.2.2A.4.4
6.2.2A.4.5
6.2.2A.4.1
6.2.2A.4.2
6.2.2B
6.2.2B.1
6.2.2B.2
6.2.2B.3
6.2.2B.4
6.2.2B.4.1
6.2.2B.4.2
6.2.2B.4.3
6.2.2B.5
6.2.2B_1
6.2.2B_1.1
6.2.2B_1.2
6.2.2B_1.3
6.2.2B_1.4
6.2.2B_1.5
6.2.2C
Transmit power .............................................................................................................................................. 255
Void .......................................................................................................................................................... 255
UE Maximum Output Power .................................................................................................................... 255
Test purpose ........................................................................................................................................ 255
Test applicability ................................................................................................................................. 255
Minimum conformance requirements ................................................................................................. 255
Test description ................................................................................................................................... 257
Initial condition ............................................................................................................................. 257
Test procedure ............................................................................................................................... 258
Message contents ........................................................................................................................... 258
Test requirements ................................................................................................................................ 258
Maximum Output Power for HPUE ......................................................................................................... 260
Test purpose ........................................................................................................................................ 260
Test applicability ................................................................................................................................. 260
Minimum conformance requirements ................................................................................................. 260
Test description ................................................................................................................................... 261
Test requirements ................................................................................................................................ 262
UE Maximum Output Power for CA ........................................................................................................ 262
Minimum conformance requirements ................................................................................................. 262
UE Maximum Output Power for CA (intra-band contiguous DL CA and UL CA) ............................ 264
Test purpose .................................................................................................................................. 264
Test applicability ........................................................................................................................... 264
Minimum conformance requirements ............................................................................................ 264
Test description ............................................................................................................................. 264
Test Requirements ......................................................................................................................... 266
UE Maximum Output Power for CA and HPUE (intra-band contiguous DL CA and UL CA) .......... 267
Test purpose .................................................................................................................................. 267
Test applicability ........................................................................................................................... 267
Minimum conformance requirements ............................................................................................ 267
Test description ............................................................................................................................. 267
Test Requirements ......................................................................................................................... 267
UE Maximum Output Power for CA (inter-band DL CA and UL CA) .............................................. 268
Test purpose .................................................................................................................................. 268
Test applicability ........................................................................................................................... 268
Minimum conformance requirements ............................................................................................ 268
Test description ............................................................................................................................. 268
Test Requirements ......................................................................................................................... 270
UE Maximum Output Power for CA (intra-band non-contiguous DL CA and UL CA) .................... 272
UE Maximum Output Power for CA (3UL CA) ................................................................................. 272
Test purpose .................................................................................................................................. 272
Test applicability ........................................................................................................................... 272
Minimum conformance requirements ............................................................................................ 272
Test description ............................................................................................................................. 272
Test Requirements ......................................................................................................................... 277
Void..................................................................................................................................................... 278
Void..................................................................................................................................................... 278
UE Maximum Output Power for UL-MIMO ............................................................................................ 278
Test purpose ........................................................................................................................................ 278
Test applicability ................................................................................................................................. 278
Minimum conformance requirements ................................................................................................. 278
Test description ................................................................................................................................... 280
Initial condition ............................................................................................................................. 280
Test procedure ............................................................................................................................... 281
Message contents ........................................................................................................................... 281
Test requirements ................................................................................................................................ 281
HPUE Maximum Output Power for UL-MIMO ....................................................................................... 283
Test purpose ........................................................................................................................................ 283
Test applicability ................................................................................................................................. 283
Minimum conformance requirements ................................................................................................. 283
Test description ................................................................................................................................... 283
Test requirements ................................................................................................................................ 284
285
ETSI
3GPP TS 36.521-1 version 15.5.0 Release 15
5
ETSI TS 136 521-1 V15.5.0 (2019-07)
6.2.2D
6.2.2D.0
6.2.2D.1
6.2.2D.1.1
6.2.2D.1.2
6.2.2D.1.3
6.2.2D.1.4
6.2.2D.1.5
6.2.2D.2
6.2.2D.2.1
6.2.2D.2.2
6.2.2D.2.3
6.2.2D.2.4
6.2.2E
6.2.2E.1
6.2.2E.2
6.2.2E.3
6.2.2E.4
6.2.2E.4.3
6.2.2E.5
6.2.2EA
6.2.2EA.1
6.2.2EA.2
6.2.2EA.3
6.2.2EA.4
6.2.2EA.4.3
6.2.2EA.5
6.2.2EB
6.2.2EB.1
6.2.2EB.2
6.2.2EB.3
6.2.2EB.4
6.2.2EB.4.1
6.2.2EB.4.2
6.2.2EB.4.3
6.2.2EB.5
6.2.2EC
6.2.2EC.1
6.2.2EC.2
6.2.2EC.3
6.2.2EC.4
6.2.2EC.4.1
6.2.2EC.4.2
6.2.2EC.4.3
6.2.2EC.5
6.2.2F
6.2.2F.1
6.2.2F.2
6.2.2F.3
6.2.2F.4
6.2.2F.4.1
6.2.2F.4.2
6.2.2F.4.3
6.2.2F.5
6.2.2FA
6.2.2FA.1
6.2.2FA.2
6.2.2FA.3
6.2.2FA.4
6.2.2FA.5
6.2.2G
UE Maximum Output Power for ProSe .................................................................................................... 285
Minimum conformance requirements ................................................................................................. 285
UE Maximum Output Power for ProSe Discovery ............................................................................. 285
Test purpose .................................................................................................................................. 285
Test applicability ........................................................................................................................... 285
Minimum Conformance requirements ........................................................................................... 285
Test description ............................................................................................................................. 285
Test requirements .......................................................................................................................... 287
UE Maximum Output Power for ProSe Direct Communication ......................................................... 287
Test purpose .................................................................................................................................. 287
Test applicability ........................................................................................................................... 287
Minimum conformance requirements ............................................................................................ 287
Test description ............................................................................................................................. 287
UE Maximum Output Power for UE category 0 ....................................................................................... 288
Test purpose ........................................................................................................................................ 288
Test applicability ................................................................................................................................. 288
Minimum conformance requirements ................................................................................................. 288
Test description ................................................................................................................................... 288
Message contents ........................................................................................................................... 289
Test requirements ................................................................................................................................ 289
UE Maximum Output Power for UE category M1 ................................................................................... 291
Test purpose ........................................................................................................................................ 291
Test applicability ................................................................................................................................. 291
Minimum conformance requirements ................................................................................................. 291
Test description ................................................................................................................................... 292
Message contents ........................................................................................................................... 294
Test requirements ................................................................................................................................ 294
UE Maximum Output Power for UE category 1bis .................................................................................. 295
Test purpose ........................................................................................................................................ 295
Test applicability ................................................................................................................................. 295
Minimum conformance requirements ................................................................................................. 295
Test description ................................................................................................................................... 296
Initial conditions ............................................................................................................................ 296
Test procedure ............................................................................................................................... 296
Message contents ........................................................................................................................... 296
Test requirement ................................................................................................................................. 296
UE Maximum Output Power for UE category M2 ................................................................................... 297
Test purpose ........................................................................................................................................ 297
Test applicability ................................................................................................................................. 297
Minimum conformance requirements ................................................................................................. 297
Test description ................................................................................................................................... 297
Initial condition ............................................................................................................................. 297
Test procedure ............................................................................................................................... 298
Message contents ........................................................................................................................... 298
Test requirements ................................................................................................................................ 299
UE Maximum Output Power for category NB1 and NB2 ........................................................................ 299
Test purpose ........................................................................................................................................ 299
Test applicability ................................................................................................................................. 299
Minimum conformance requirements ................................................................................................. 299
Test description ................................................................................................................................... 300
Initial condition ............................................................................................................................. 300
Test procedure ............................................................................................................................... 300
Message contents ........................................................................................................................... 301
Test requirements ................................................................................................................................ 301
UE Maximum Output Power for category NB1 and NB2/Power Class 6 ................................................ 301
Test purpose ........................................................................................................................................ 301
Test applicability ................................................................................................................................. 301
Minimum conformance requirements ................................................................................................. 301
Test description ................................................................................................................................... 302
Test requirements ................................................................................................................................ 302
UE Maximum Output Power for V2X Communication ........................................................................... 303
ETSI
3GPP TS 36.521-1 version 15.5.0 Release 15
6
ETSI TS 136 521-1 V15.5.0 (2019-07)
6.2.2G.1
6.2.2G.1.1
6.2.2G.1.2
6.2.2G.1.3
6.2.2G.1.4
6.2.2G.1.4.1
6.2.2G.1.4.2
6.2.2G.1.4.3
6.2.2G.1.5
6.2.2G.2
6.2.2G.2.1
6.2.2G.2.2
6.2.2G.2.3
6.2.2G.2.4
6.2.2G.2.4.1
6.2.2G.2.4.2
6.2.2G.2.4.3
6.2.2G.2.5
6.2.2G.3
6.2.2G.3.1
6.2.2G.3.2
6.2.2G.3.3
6.2.2G.3.4
6.2.2G.3.4.1
6.2.2G.3.4.2
6.2.2G.3.4.3
6.2.2G.3.5
6.2.2G.4
6.2.2G.4.1
UE Maximum Output Power for V2X Communication / Non-concurrent with E-UTRA uplink
transmission ........................................................................................................................................ 303
Test purpose .................................................................................................................................. 303
Test applicability ........................................................................................................................... 303
Minimum conformance requirements ............................................................................................ 303
Test description ............................................................................................................................. 303
Initial conditions ...................................................................................................................... 303
Test procedure .......................................................................................................................... 304
Message contents ..................................................................................................................... 304
Test requirements .......................................................................................................................... 304
UE Maximum Output Power for V2X Communication / Simultaneous E-UTRA V2X sidelink
and E-UTRA uplink transmission ....................................................................................................... 305
Test purpose .................................................................................................................................. 305
Test applicability ........................................................................................................................... 305
Minimum conformance requirements ............................................................................................ 305
Test description ............................................................................................................................. 305
Initial conditions ...................................................................................................................... 305
Test procedure .......................................................................................................................... 306
Message contents ..................................................................................................................... 306
Test requirements .......................................................................................................................... 307
UE Maximum Output Power for V2X Communication / Intra-band contiguous multi-carrier
operation ............................................................................................................................................. 307
Test purpose .................................................................................................................................. 307
Test applicability ........................................................................................................................... 307
Minimum conformance requirements ............................................................................................ 307
Test description ............................................................................................................................. 308
Initial conditions ...................................................................................................................... 308
Test procedure .......................................................................................................................... 308
Message contents ..................................................................................................................... 308
Test requirements .......................................................................................................................... 309
UE Maximum Output Power for V2X Communication / Power class 2 ............................................. 309
UE Maximum Output Power for V2X Communication / Power class 2 / Non-concurrent with
E-UTRA uplink transmissions ....................................................................................................... 309
Test purpose ............................................................................................................................. 309
Test applicability ...................................................................................................................... 309
Minimum conformance requirements ...................................................................................... 309
Test description ........................................................................................................................ 309
Initial conditions ................................................................................................................. 309
Test procedure .................................................................................................................... 310
Message contents................................................................................................................ 310
Test requirements ..................................................................................................................... 310
Maximum Power Reduction (MPR) ......................................................................................................... 310
Test purpose ........................................................................................................................................ 311
Test applicability ................................................................................................................................. 311
Minimum conformance requirements ................................................................................................. 311
Test description ................................................................................................................................... 311
Initial condition ............................................................................................................................. 311
Test procedure ............................................................................................................................... 313
Message contents ........................................................................................................................... 313
Test requirements ................................................................................................................................ 313
Maximum Power Reduction (MPR) for HPUE ........................................................................................ 315
Test purpose ........................................................................................................................................ 315
Test applicability ................................................................................................................................. 315
Minimum conformance requirements ................................................................................................. 316
Test description ................................................................................................................................... 316
Test requirements ................................................................................................................................ 316
Maximum Power Reduction (MPR) for Multi-Cluster PUSCH ............................................................... 316
Test purpose ........................................................................................................................................ 316
Test applicability ................................................................................................................................. 317
Minimum conformance requirements ................................................................................................. 317
Test description ................................................................................................................................... 317
Initial condition ............................................................................................................................. 317
6.2.2G.4.1.1
6.2.2G.4.1.2
6.2.2G.4.1.3
6.2.2G.4.1.4
6.2.2G.4.1.4.1
6.2.2G.4.1.4.2
6.2.2G.4.1.4.3
6.2.2G.4.1.5
6.2.3
6.2.3.1
6.2.3.2
6.2.3.3
6.2.3.4
6.2.3.4.1
6.2.3.4.2
6.2.3.4.3
6.2.3.5
6.2.3_1
6.2.3_1.1
6.2.3_1.2
6.2.3_1.3
6.2.3_1.4
6.2.3_1.5
6.2.3_2
6.2.3_2.1
6.2.3_2.2
6.2.3_2.3
6.2.3_2.4
6.2.3_2.4.1
ETSI
3GPP TS 36.521-1 version 15.5.0 Release 15
7
ETSI TS 136 521-1 V15.5.0 (2019-07)
6.2.3_2.4.2
6.2.3_2.4.3
6.2.3_2.5
6.2.3_3
6.2.3_3.1
6.2.3_3.2
6.2.3_3.3
6.2.3_3.4
6.2.3_3.4.1
6.2.3_3.4.2
6.2.3_3.4.3
6.2.3_3.5
6.2.3_4
6.2.3_4.1
6.2.3_4.2
6.2.3_4.3
6.2.3_4.4
6.2.3_4.4.1
6.2.3_4.4.2
6.2.3_4.4.3
6.2.3_4.5
6.2.3_5
6.2.3_5.1
6.2.3_5.2
6.2.3_5.3
6.2.3_5.4
6.2.3_5.4.1
6.2.3_5.4.2
6.2.3_5.4.3
6.2.3_5.5
6.2.3_6
6.2.3_6.1
6.2.3_6.2
6.2.3_6.3
6.2.3_6.4
6.2.3_6.4.1
6.2.3_6.4.2
6.2.3_6.4.3
6.2.3_6.5
6.2.3A
6.2.3A.1
6.2.3A.1.1
6.2.3A.1.2
6.2.3A.1.3
6.2.3A.1.4
6.2.3A.1.5
6.2.3A.1_1
6.2.3A.1_1.1
6.2.3A.1_1.2
6.2.3A.1_1.3
6.2.3A.1_1.4
6.2.3A.1_1.5
6.2.3A.1_2
6.2.3A.1_2.1
6.2.3A.1_2.2
6.2.3A.1_2.3
6.2.3A.1_2.4
6.2.3A.1_2.5
6.2.3A.1_3
Test procedure ............................................................................................................................... 318
Message contents ........................................................................................................................... 318
Test requirements ................................................................................................................................ 318
Maximum Power Reduction (MPR) for UL 64QAM ............................................................................... 319
Test purpose ........................................................................................................................................ 320
Test applicability ................................................................................................................................. 320
Minimum conformance requirements ................................................................................................. 320
Test description ................................................................................................................................... 320
Initial condition ............................................................................................................................. 320
Test procedure ............................................................................................................................... 321
Message contents ........................................................................................................................... 321
Test requirements ................................................................................................................................ 322
Maximum Power Reduction (MPR) for Multi-Cluster PUSCH with UL 64QAM ................................... 324
Test purpose ........................................................................................................................................ 324
Test applicability ................................................................................................................................. 324
Minimum conformance requirements ................................................................................................. 325
Test description ................................................................................................................................... 325
Initial condition ............................................................................................................................. 325
Test procedure ............................................................................................................................... 326
Message contents ........................................................................................................................... 326
Test requirements ................................................................................................................................ 326
Maximum Power Reduction (MPR) for UL 256QAM ............................................................................. 327
Test purpose ........................................................................................................................................ 327
Test applicability ................................................................................................................................. 328
Minimum conformance requirements ................................................................................................. 328
Test description ................................................................................................................................... 328
Initial condition ............................................................................................................................. 328
Test procedure ............................................................................................................................... 329
Message contents ........................................................................................................................... 329
Test requirements ................................................................................................................................ 329
Maximum Power Reduction (MPR) for Multi-Cluster PUSCH with UL 256QAM ................................. 331
Test purpose ........................................................................................................................................ 331
Test applicability ................................................................................................................................. 331
Minimum conformance requirements ................................................................................................. 332
Test description ................................................................................................................................... 332
Initial condition ............................................................................................................................. 332
Test procedure ............................................................................................................................... 333
Message contents ........................................................................................................................... 333
Test requirements ................................................................................................................................ 333
Maximum Power Reduction (MPR) for CA ............................................................................................. 334
Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) ................. 334
Test purpose .................................................................................................................................. 334
Test applicability ........................................................................................................................... 335
Minimum conformance requirements ............................................................................................ 335
Test description ............................................................................................................................. 336
Test Requirements ......................................................................................................................... 339
Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for UL
64QAM ............................................................................................................................................... 341
Test purpose .................................................................................................................................. 342
Test applicability ........................................................................................................................... 342
Minimum conformance requirements ............................................................................................ 342
Test description ............................................................................................................................. 343
Test requirement ............................................................................................................................ 345
Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for UL
256QAM ............................................................................................................................................. 346
Test purpose .................................................................................................................................. 346
Test applicability ........................................................................................................................... 346
Minimum conformance requirements ............................................................................................ 346
Test description ............................................................................................................................. 347
Test requirement ............................................................................................................................ 348
Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA) for
HPUE .................................................................................................................................................. 349
ETSI
相关推荐
2023年江西萍乡中考道德与法治真题及答案.doc
2012年重庆南川中考生物真题及答案.doc
2013年江西师范大学地理学综合及文艺理论基础考研真题.doc
2020年四川甘孜小升初语文真题及答案I卷.doc
2020年注册岩土工程师专业基础考试真题及答案.doc
2023-2024学年福建省厦门市九年级上学期数学月考试题及答案.doc
2021-2022学年辽宁省沈阳市大东区九年级上学期语文期末试题及答案.doc
2022-2023学年北京东城区初三第一学期物理期末试卷及答案.doc
2018上半年江西教师资格初中地理学科知识与教学能力真题及答案.doc
2012年河北国家公务员申论考试真题及答案-省级.doc
2020-2021学年江苏省扬州市江都区邵樊片九年级上学期数学第一次质量检测试题及答案.doc
2022下半年黑龙江教师资格证中学综合素质真题及答案.doc
