如何用汇编语言实现汉字显示编程
2008 年 05 月 21 日 星期三 15:55
概述:
一般在屏幕上显示汉字的时候需要汉字系统的支持,但需要自己显示
汉字的时候,就需要自己读汉字字库文件,把字符点阵读出来,再用绘图的办法
显示到屏幕上,本文是读 UCDOS 16 点字库文件的示例。
在 UCDOS 的点阵字库 HZK16 中,字符点阵是按照汉字内码排列的,汉
字的内码从一些图形字符开始,起始编码为 A1A1H,汉字内码第一位为区码,每
区为 94 个汉字,第二位为每区内的编码,每个汉字的点阵为 16 点*16 点 共
32 字节,数据按第一行 1-8 点,9-16 点,第二行 1-8 点,9-16 点...排列,每
位数据 1 为要显示点,0 为不显示点。汉字点阵数据在字库中的偏移量为 ((区
码-A1H)*94 + (区内编码-A1H))*32。
本程序为一个简单的例子,要显示的汉字在变量 DISP_DATA 中,且没有
考虑汉字、英文混用的情况。
源程序:
.286
LINE_CHAR EQU 210 ;在屏幕上第几行显示
COL_CHAR EQU 230 ;在屏幕上第几列显示
COLOR_CHAR EQU 0EH ;显示颜色
CHARS
CODE
SEGMENT
EQU (offset disp_data_end-offset disp_data)/2
ASSUME CS:CODE,DS:CODE
ORG 100H
START:
jmp install
DB 'C:\UCDOS\HZK16',0 ;字库文件名,用 UCDOS 的 16 点阵汉字库
DW ?
;file handle
CC_FILE
HANDLE
DISP_DATA DB '罗云彬'
DISP_DATA_END EQU THIS BYTE
D_OPEN_ERROR DB 'File C:\UCDOS\HZK16 not found !',0dh,0ah,24h
install:
;要显示的汉字
;打开汉字库
mov ax,3d00h
mov dx,offset cc_file
int 21h
jnb open_ok
mov ah,9
mov dx,offset d_open_error
int 21h
int 20h
open_ok:
mov handle,ax
mov si,offset disp_data
mov di,offset zi_buffer
mov cx,chars
cld
ins2:
lodsb
mov ah,al
lodsb
call get_dots ;读出汉字点针
loop ins2
call disp_cc ;显示到屏幕
int 20h
GET_DOTS PROC
pusha
sub ax,0a1a1h ;汉字的内码从 A1 区开始
;所以绝对开始区是内码-A1
;点阵在字库中的位置为
;((汉字码 1-A1)* 94 + 汉字码 2 - A1)* 32
cwd
mov dl,al
mov al,ah
cbw
mov bl,94
mul bl
add ax,dx
mov bx,32
mul bx
mov cx,dx
mov dx,ax
mov ax,4200h ;移动读写指针到点阵数据位置
mov bx,handle
int 21h
mov ah,3fh
mov cx,32
mov dx,di
int 21h
popa
add di,32
ret
GET_DOTS ENDP
DISP_CC
PROC
mov ax,12h
;640*480 mode
int 10h
;设置 640*480/16 色显示模式
mov cx,chars
mov si,offset zi_buffer
mov bx,col_char-20 ;BX = column
dh_lop0:
add bx,20
push cx
mov cx,16
;every char column+20
;l6 lines/char
mov dx,line_char ;DX = start line
dh_lop1:
push bx
push cx
lodsb
;16 dots/line
mov ah,al
lodsb
mov cx,16
dh_lop2:
shl ax,1
push ax
push bx
push cx
jc db_color
xor al,al
jmp short db_draw
;back color is 0
db_color:
mov al,color_char
db_draw:
mov ah,0ch
mov cx,bx
xor bh,bh
int 10h
pop cx
pop bx
pop ax
inc bx
loop dh_lop2
;inc column
inc dx
;next line
pop cx
pop bx
loop dh_lop1
pop cx
loop dh_lop0
xor ah,ah
int 16h
mov ax,3
int 10h
ret
DISP_CC
ZI_BUFFER EQU THIS BYTE
ENDP
ENDS
CODE
END START